how to change gear of pulsar 150

You search Auto repair manual PDF how to change gear of pulsar 150, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to change gear of pulsar 150 Direct Download speed 5282 Kb/s

  how to change gear of pulsar 150 Full Version speed 6162 Kb/s



2003 – 2008 4Runner AND 2007 – 2008 FJ Cruiser FRONT AND REAR DIFFERENTIAL GEAR OIL SPECIFICATION CHANGE

0

Filed Under (Toyota Manuals) by admin on 14-11-2011

download
75W-85 GL5 synthetic gear oil beginning with the 2008 model year. This new synthetic gear oil is compatible with 2003 – 2007 model year 4Runner and 2007 model year FJ Cruiser differentials. Please refer to the Parts Information section below for information about this gear oil and use this gear oil (or equivalent) when filling front or rear differentials with oil. 2003 – 2008 model year 4Runner vehicles. 2007 – 2008 model year FJ Cruiser vehicles. PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME TYPE QTY N/A 08885-02606 Toyota Genuine Differential Gear Oil LX 75W-85 API GL-5 SAE 75W-85 LSD As Needed N/A 08885-02506 Toyota Genuine Differential Gear Oil LT 75W-85 API GL-5 SAE 75W-85 w/o LSD As Needed Refer to the diagram below to identify if LSD or non-LSD gear oil is used on the vehicle. For applicable vehicles, there is a caution label above the filler plug, as shown below

Incoming search terms:

2007 Ural Models Gear Up Patrol Tourist Installation Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Font Brake Control Lever Clutch control lever: When the clutch lever is squeezed, the engine is disengaged from the gearbox. When the lever is released, the engine and gearbox are engaged. WARNING: MAKE SURE FINGERS ARE NOT POSITIONED BETWEEN HAND CONTROL LEVERS AND HANDLEBAR GRIPS OR OPERATION OF VEHICLE COULD BE IMPAIRED . WARNING: B EFORE STARTING ENGINE , ALWAYS SHIFT TRANSMISSION TO NEUTRAL TO PREVENT ACCIDENTAL MOVEMENT WHICH COULD CAUSE POSSIBLE DAMAGE TO MOTORCYCLE AND PERSONAL INJURY . Caution: Always engage the clutch release lever when shifting. Serious internal damage may result to the transmission if the clutch release lever is not engaged. Front brake control lever: When the lever is squeezed, the front wheel brake is actuated. The front brake should be used together with rear brake. When the brake lever is squeezed, the stop signal lights are switched on. 19 Kickstart lever : Designed to start the engine. Upon kicking the lever the crankshaft is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift lever: This is a heal shift type of lever. To shift up from a low gear to a high gear the rear arm(heal shift) is pressed. To shift down from a high gear to a low gear the from arm is depressed. Since the heel-toe shift lever is short-coupled, it is much easier to shift up using the heal shift, and to shift down using the toe shift with the ball of your foot. The neutral gear is between the 1st and 2nd gears. It is important to shift smoothly with a constant force, and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pressed. NOTE: The neutral lamp will illuminate when the transmission is in neutral. (see “Starting the Engine”). Gear Shift Foot Pedal Kick Lever 20 Parking Brake Sidecar Drive Lever Rear Brake Pedal Parking Brake: Used to hold the bike when parked. To engage, press the rear brake pedal, push down and twist the parking brake lever counter clockwise. Sidecar drive engagement lever: Used to engage the drive axle to the sidecar wheel on the Patrol and Gear Up model motorcycles. WARNING: Never engage sidecar drive on concrete or hard surface. Severe damage to drivetrain will result if the sidecar drive is engaged on pavement. Rear brake lever: Actuates the rear brakes on both the motorcycle and sidecar. WARNING: DO NOT APPLY EITHER BRAKE STRONGLY ENOUGH TO LOCK THE WHEELS BECAUSE THIS MAY CAUSE POSSIBLE LOSS OF CONTROL OF THE MOTORCYCLE . ALWAYS USE BOTH BRAKES . NEVER STOP WITH FRONT OR REAR BRAKE ONLY . WARNING: AN IMPROPERLY ADJUSTED REAR BRAKE PEDAL COULD INTERFERE WITH PROPER REAR BRAKE OPERATION RESULTING IN POOR BRAKE ACTION

Incoming search terms:

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

Moto Guzzi Sport 1100i Owners Manual

0

Filed Under (Moto Guzzi) by admin on 29-11-2010

download
General features Identification data Instruments and controls Riding your motorcycle Break-in Maintenance and adjustments Wheel removal Service schedule Cleaning – Storing Cleaning the windscreen Lubrication Valve gear WEBER injectionignition system (I.A.W.) Electrical equipment Wiring diagram Illustrations Lubrication Pressure fed by gear pump. Oil filters: wire mesh inside sump and replaceable cartridge filter outside sump. Normal lubrication pressure 3.8Ö 4.2 [5] kg/cm2, pressure valve, thermostat and cooler. Low oil pressure sensor (electrical) on crankcase. Generator/Alternator On front of crankshaft (1 4V – 25A). Ignition “WEBER MARELLI” electronic digital induced discharge, with high efficiency coil. Spark plugs: Spark plug gap: 0,7 mm. SPORT 1100 DAYTONA R NGK BPR 6 ESI NGK DR9 E IMS Starting Electric starter (12V-1,2 kW) with solenoid engagement. Ring gear bolted on flywheel. Starter button (START) on right of handlebars. Driveline data Clutch Twin driven plates, dry type, on flywheel. Hand controlled by lever on left of handlebars. Primary drive By gears. Ratio: 1 to 1.3529 (tooth ratio 17/23). Gearbox 5-speed, with constantly meshed gears with front dog clutch. Incorporated cush drive. Pedal operated on the left side of the motorcycle. Gear ratios: Low gear = 1 to 1,812 (tooth ratio 16/29) 2nd gear = 1 to 1,250 (tooth ratio 20/25) 3rd gear = 1 to 1 (tooth ratio 23/23) 4th gear = 1 to 0,833 (tooth ratio 24/20) 5th gear = 1 to 0,730 (tooth ratio 26/19) Ratio: 1:4,125 (tooth ratio 8/33) Overall gear ratios (Engine-wheel): Low gear = 1 to 10,1150 2nd gear = 1 to 6,9761 3rd gear = I to 5,5809 4th gear = 1 to 4,6507 5th gear = 1 to 4,0783 Frame Rectangular section single-beam in NiCrMo steel. Semisupporting engine base. Suspensions Front: White Power upside-down hydraulic telescopic fork with individually adjustable rebound and compression; Rear: steel swing arm with oval cross section. Single shock absorber White Power with separate adjustment of spring preload and of hydraulic rebound and compression damping. Wheels Light alloy castings with 3 hollow spokes (rear wheel with cush drive unit). Rim sizes: – front: 3,50x 17 MT H2 – rear: 4,50×17 MT H2 Tires -front: 120/70 ZR 17 – rear: 160/70 ZR 17 [160/60 ZR 17] Type: Tubeless Front: two Brembo drilled semi-floating disc brakes in stainless steel for SPORT I 100; [two Brembo drilled floating discs, Racing type for DAYTONA RS] with fixed 4 differential piston calipers. Adjustable manual control lever on the right side of the handle-bar; – disc 320 mm;

Incoming search terms:

HARLEY-DAVIDSON BIG TWINS COMPUFIRE 1084 GEAR SETS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 26-11-2010

download
1. Remove the seat and disconnect the cables at the battery. Remove the ground cable first and then the positive (+) cable. 2. Drain the oil in the outer primary case and remove the outer primary cover following instructions in the Factory Shop manual. 3. Bend the tab on the jackshaft bolt away from the bolt head. Remove the starter pinion gear with the jackshaft bolt, lock plate and washer. 4. Remove the clutch assembly using the procedure found in the Factory Shop manual. 5. Remove the original equipment ring gear from the clutch basket by drilling out the rivets with a 5/16-inch drill bit. Drill through the rivet head and tap the ring gear off the clutch basket using a hammer. 6. Drill out the six holes in the clutch basket with the 5/16-inch drill bit. RING AND STARTER PINION GEAR INSTALLATION 1. Attach the new 84-tooth ring gear to the clutch basket using the six 5/16×24 socket head cap screws supplied. NOTE… The bevel side of the ring gear (identified by the three dots) faces away from the starter motor. Torque the socket head cap screws to 29 ft lbs. 2. Assemble and install the primary drive assembly following the instructions in the factory Shop manual. 3. Install the new 10-tooth pinion gear with the jackshaft bolt, lock plate and thrust washer. Torque the jackshaft bolt to 7 – 9 ft lbs. Bend the lock tab on the lock plate against a flat on the jackshaft bolt head. 4. Measure and adjust the air gap between the ring gear and the pinion gear. See Fig-1 . The correct gap is .075 – .125 inch. If the gap is larger than .125 inch, use the supplied shim washers inside the jackshaft coupler. See Fig-2 . If the air gap is smaller than .075 inch, the jackshaft must be shortened by removing material from the splined end of the shaft. See Fig-3 . 5. Install the outer primary cover following instructions in the Factory Shop manual and refill the primary case with the proper amount of primary oil. 6. Re-install the battery cables in the reverse order they were removed. Re-install the seat

Incoming search terms:

COMPUFIRE 1084 GEAR SETS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
1. Remove the seat and disconnect the cables at the battery. Remove the ground cable first and then the positive (+) cable. 2. Drain the oil in the outer primary case and remove the outer primary cover following instructions in the Factory Shop manual. 3. Bend the tab on the jackshaft bolt away from the bolt head. Remove the starter pinion gear with the jackshaft bolt, lock plate and washer. 4. Remove the clutch assembly using the procedure found in the Factory Shop manual. 5. Remove the original equipment ring gear from the clutch basket by drilling out the rivets with a 5/16-inch drill bit. Drill through the rivet head and tap the ring gear off the clutch basket using a hammer. 6. Drill out the six holes in the clutch basket with the 5/16-inch drill bit. RING AND STARTER PINION GEAR INSTALLATION 1. Attach the new 84-tooth ring gear to the clutch basket using the six 5/16×24 socket head cap screws supplied. NOTE… The bevel side of the ring gear (identified by the three dots) faces away from the starter motor. Torque the socket head cap screws to 29 ft lbs. 2. Assemble and install the primary drive assembly following the instructions in the factory Shop manual. 3. Install the new 10-tooth pinion gear with the jackshaft bolt, lock plate and thrust washer. Torque the jackshaft bolt to 7 – 9 ft lbs. Bend the lock tab on the lock plate against a flat on the jackshaft bolt head. 4. Measure and adjust the air gap between the ring gear and the pinion gear. See Fig-1 . The correct gap is .075 – .125 inch. If the gap is larger than .125 inch, use the supplied shim washers inside the jackshaft coupler. See Fig-2 . If the air gap is smaller than .075 inch, the jackshaft must be shortened by removing material from the splined end of the shaft. See Fig-3 . 5. Install the outer primary cover following instructions in the Factory Shop manual and refill the primary case with the proper amount of primary oil. 6. Re-install the battery cables in the reverse order they were removed. Re-install the seat

Incoming search terms:

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

Harley-Davidson Six Speed Transmissions FLH 2009 Up Champion Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
Preparation Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the clutch release cover (right side). 2.6 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.7 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.8 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Snap-On Part No: FWA62121 Snap-On Part No: FWA62121 Champion Part No: RG-100-100 Reverse Gear Installation Instructions Harley-Davidson Six Speed Transmission HD FLH 2009 Up Page 3 of 5 Revision 2 Boring Tool 3 Installation 3.1 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.2 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 1 3.3 Install the supplied (ear)plug into the main shaft hole. To be removed later. 3.4 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 2 3.5 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.6 Remove torque wrench from special tool. Do not remove special tool from small gear. 3.7 Using the supplied boring tool and the special tool as a guide, drill the main shaft through two holes of the special tool as shown. Stop when cutter contacts bearing race. Figure 3 3.8 Remove special tool, leaving main shaft plug in place, and thoroughly clean out the holes. Use care to ensure debris does not enter transmission. 3.9 Remove plug from main shaft hole. Figure 1 Figure 2 Figure 3 Note: To prevent gears from rotating during torque procedures, engage transmission into 1st gear and apply brakes Note: Frequently stop cutting and remove bit from hole to clean bit and vacuum debris from hole

Incoming search terms:

2003 Model Ural Gear Up, Patrol, Tourist Owners Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
19 Kick lever Is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift foot pedal Is a two-arm type. When the front arm is depressed, shifting from higher to lower gear takes place. When the rear arm is depressed, shifting from lower to higher gear takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift into a higher gear if you do not use your heel to shift, rather the ball of your foot. The neutral position is fixed between the 1st and 2nd gears. It is important to shift smoothly with a constant force and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pushed. IMPORTANT! The green pilot lamp will illuminate when either the transmission is in neutral or when the reverse gear is engaged (see “Starting the Engine”). Turn indicator pilot lamp indicates that the turn signals are activated. Alternator fault indicator lamp , indicates that the charging system is malfunctioning and needs immediate attention. Gearbox neutral and reverse gear engagement , indicates that the gearbox is either in neutral or in reverse. Head lamp high beam indicator , indicates that the headlight high beam is activated. Speedometer is on the dash board, with trip and total odometer. The trip odometer is reset to zero by rotating knob (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers not miles.

Incoming search terms:

MACHINE SPECIFICATION FOR 115cc (UNDERBONE) (4-stroke horizontal layout engine)

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
(This is for clarification only. Other parts not listed in Art. 2.5 & 2.6 can be altered or replaced. Change of specification means modification, changes or removal of the parts.) 2.6.1 Change of compression ratio is allowed. 2.6.2 Setting of carburetor, attachment or size change of air funnel. 2.6.3 Inlet opening of fuel tank for fuel charge may be modified but cannot be relocated. 2.6.4 Change of fuel pipe and fuel cork. 2.6.5 Change of exhaust pipe and muffler, but must have silencer. 2.6.6 Material of clutch discs and specifications of spring. Hand clutch is allowed. 2.6.7 Gear ratios are free. 2.6.8 Starting device and parts relative to this device may be removed. 2.6.9 Modification or removal of air cleaner box, wire harness and control wires. 2.6.10 Removal of speedometer (including meter gearbox and cable.) 2.6.11 Removal of drive chain case and cover. Change of drive chain is allowed. 2.6.12 Change of final gear ratio is allowed. 2.6.13 Attachment of bead stopper and balance weight to tyre. 2.6.14 Modification and change of rear brake part is allowed. 2.6.15 Frame body may be strengthened. 2.6.16 Modification and change to brackets and pedals including footrest. 2.6.17 Front suspension unit must remain as originally produced by the manufacturer. However, the following internal parts of the fork can be modified: Shims, hydraulic piston, oil passages, springs and spacers. 2.6.18 Attachment of stabilizer to strengthen or reinforcing rear swing arm is allowed. 2.6.19 Removal of dust seals. 2.6.20 Rear suspension unit must remain as originally produced by the manufacturer. However rear suspension unit is free. The rear linkage must remain as originally produced by the manufacturer. 2.6.21 Handle bars, clutch and front brake lever may be changed by an after market copy. Clutch springs may be changed. 2.6.22 Steering dampers may be fitted. They must not act in any way as a steering lock limiting device. 2.6.23 Materials of streamlining and material of seat cowling. (However, expensive materials such as carbon fibre and kevlar are not allowed). 2.6.24 Removal of rear mudguard and side cover. Front mudguard may be cut but not less than 6 inches from the front fork on original part. 2.6.25 All lubricants are free 2.6.26 Adjusting and polishing any parts are allowed. Adjusting is defined as : “To select each part or assembly complete with-in the limit of single or total tolerance” (i.e. that of valve clearance, ignition timing etc.) 2.6.27 Cutting unnecessary stays is

Incoming search terms:

Incoming search terms: