how to change headlight bulb of hero mastro

You search Auto repair manual PDF how to change headlight bulb of hero mastro, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to change headlight bulb of hero mastro Direct Download speed 5282 Kb/s

  how to change headlight bulb of hero mastro Full Version speed 6162 Kb/s



YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

Ducati SPORT TOURING HEADLIGHT UPGRADE INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
1. Remove the following fairing components per the instructions in the Ducati owners manual: • Instrument surrounds • Headlight fairing • Chin fairing (under headlight/air intake) • Right-side middle fairing (covers battery) 2. Disconnect the speedometer cable from the speedometer. Unthread the ring nut at the top of the speedometer cable and retract the cable downward about 4-6 inches. 3. Disconnect the headlight wiring from the headlight bulbs. Retract the rubber boots at the rear of the headlight assembly to gain access to the wire terminals. Note that the two ¼ inch terminals at the high- beam bulb have locking clips that should be depressed before pulling the terminal away from the bulb. 4. Unplug the parking light from the headlight body by grasping the wires and carefully pulling it out. 5. Remove the two rubber plugs covering the lower headlight mounting screw access holes beneath the air intake horn. 6. Using an 8mm hex socket inserted through the lower access holes remove the two hex-head bolts securing the bottom of the headlight to the frame. 7. Using the same socket wrench, remove the two 8mm hex-head bolts securing the top of the headlight assembly to the frame. 8. Remove the headlight assembly from the frame. 9. Remove the two rubber grommets and steel reducing sleeves from the frame at the top mounting locations for the headlight. Leave the lower pair in place; these will be re-used, as shown in Figure 6

Incoming search terms:

YAMAHA FJR1300N PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 17-12-2010

download
Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant- voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. EAU04076* Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuel injection system fuse 2. Spare fuel injection system fuse 1. Headlight fuse 2. Signaling system fuse 3. Ignition fuse 4. Windshield motor fuse 5. Radiator fan fuse 6. Backup fuse (odometer and clock) 7. Spare fuse (〈 4)
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 6 EC000103 CAUTION: Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU04099 Replacing a headlight bulb This motorcycle is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B (if replacing the left headlight bulb) or panel C (if replacing the right headlight bulb). (See page 6-7 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the headlight bulb cove

Incoming search terms:

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

Ducati streetfighter HID headlight system installation Manual

0

Filed Under (Ducati) by admin on 26-10-2010

download
The installation of this kit requires the removal of the Helmholtz air box between the air intakes, located directly in front of the main air box. You will also need to run a wire from the front of the bike to the back of the bike where the battery is located. 1. Remove the seat, tail section, and fuel tank. 2. Remove the headlight assembly. 3. Replace the headlight bulb with the included HID bulb. You will need to modify the cap for the back of the headlight to allow the wires to pass through. 4. You will need to mount the Ballast, igniter, and the relay for the switch box in the area where the Helmholtz was. (see image) 5. Run the red power wire to the back of the bike and connect directly to the positive lead on the battery terminal. 6. Connect the ground wire the frame where the Helmholtz was previously bolted. 7. Plug the HID bulb into the ballast. There are 3 plugs. They can only be connected one way. 8. Connect the main wire harness to the ballast. 9. Turn the key on and turn the ignition on and check that the headlight comes on. 10. Switch on the brights to make sure this is working as well. 11. Once everything is confirmed to be working make sure the wirings are well attached won’t interfere with the fan or with any of the steering components. 12. Re-install the tank, tail section, and seat

2008-2009 KAWASAKI TERYX HEADLAMPS HIDTERYX HID KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
a. Remove rubber boot from the back of the headlamp housing assembly. b. Push down on metal latch and pull away from lip to release halogen bulb. Pull out halogen bulb. c. Insert HID bulb, line up bulb to fit into the bulb holder, lower latch to lock bulb in place. d. Replace Rubber boot on the back headlamp assembly. (Make sure to pull wires through the center of the rubber boot first before you start to pull down boot on the back of the headlamp assembly.) e. Make sure that the wiring, coming from the HID bulb, clears the black plastic housing that encases the headlamp assembly so connection from the bulb to the ballast is possible. If installed correctly there is no need for drilling or modifications of any type. 2. Ballast a. Mount ballast in location of your choice – recommended near the headlight. 3. Wiring Note: DO NOT modify the wiring that runs from the HID bulb to the ballast. It will cause the system to work improperly. It will void the warranty . a. Once ballast is installed connect corresponding wires from HID bulb to corresponding male / female plugs on ballast. b. To connect wiring from ballast to Teryx primary system i. Find wire extension with white triangular head with black, yellow & green wires at opposite end ii. Connect black off extension to black wire coming off ballast iii. Connect Yellow / Green wire to red wire coming off ballast iv. Connect triangular head to corresponding plug on Teryx Factory Wiring End

Incoming search terms:

MACHINE SPECIFICATION FOR 115cc (UNDERBONE) (4-stroke horizontal layout engine)

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
(This is for clarification only. Other parts not listed in Art. 2.5 & 2.6 can be altered or replaced. Change of specification means modification, changes or removal of the parts.) 2.6.1 Change of compression ratio is allowed. 2.6.2 Setting of carburetor, attachment or size change of air funnel. 2.6.3 Inlet opening of fuel tank for fuel charge may be modified but cannot be relocated. 2.6.4 Change of fuel pipe and fuel cork. 2.6.5 Change of exhaust pipe and muffler, but must have silencer. 2.6.6 Material of clutch discs and specifications of spring. Hand clutch is allowed. 2.6.7 Gear ratios are free. 2.6.8 Starting device and parts relative to this device may be removed. 2.6.9 Modification or removal of air cleaner box, wire harness and control wires. 2.6.10 Removal of speedometer (including meter gearbox and cable.) 2.6.11 Removal of drive chain case and cover. Change of drive chain is allowed. 2.6.12 Change of final gear ratio is allowed. 2.6.13 Attachment of bead stopper and balance weight to tyre. 2.6.14 Modification and change of rear brake part is allowed. 2.6.15 Frame body may be strengthened. 2.6.16 Modification and change to brackets and pedals including footrest. 2.6.17 Front suspension unit must remain as originally produced by the manufacturer. However, the following internal parts of the fork can be modified: Shims, hydraulic piston, oil passages, springs and spacers. 2.6.18 Attachment of stabilizer to strengthen or reinforcing rear swing arm is allowed. 2.6.19 Removal of dust seals. 2.6.20 Rear suspension unit must remain as originally produced by the manufacturer. However rear suspension unit is free. The rear linkage must remain as originally produced by the manufacturer. 2.6.21 Handle bars, clutch and front brake lever may be changed by an after market copy. Clutch springs may be changed. 2.6.22 Steering dampers may be fitted. They must not act in any way as a steering lock limiting device. 2.6.23 Materials of streamlining and material of seat cowling. (However, expensive materials such as carbon fibre and kevlar are not allowed). 2.6.24 Removal of rear mudguard and side cover. Front mudguard may be cut but not less than 6 inches from the front fork on original part. 2.6.25 All lubricants are free 2.6.26 Adjusting and polishing any parts are allowed. Adjusting is defined as : “To select each part or assembly complete with-in the limit of single or total tolerance” (i.e. that of valve clearance, ignition timing etc.) 2.6.27 Cutting unnecessary stays is

YAMAHA V-STAR 650/ 1100 CLASSIC F ATS/ SLIMS MOUNTING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1. Cover gas tank and front fender with towels to avoid damage during installation. 2. Install the two mounting plates onto the windshield, using the bottom and third bolt up. Leave the nylon washers off. The small tab goes to the bottom, big one at the top. (see Figure 1) Tabs face out away from the headlight when installed correctly. 3. Remove the headlight lens and chrome Turn Signal Bar cover and set them in a safe place. (see figure 2) 4. Remove the (3) socket head cap screws that hold the Headlight housing and let it rest carefully so that it does not fall. 5. Remove the turn signal bar by extracting the two socket head cap screws and let it dangle. (see figure 2) 6. Loosely install the throttle-side Bracket and Headlight using one of the (3) new longer 6mm x 30mm socket head cap screws. The nylon washer goes in between Headlight Housing and Headlight Bracket. (see figure 3) Install one of the (2) new 8mm x 45mm SS flat head screw and spacer in the lower hole to mount the turn signal bar. Insert the bolt in this order: bolt – windshield bracket – spacer – turn signal bar, and loosely tighten . (see Figure 3) Repeat these steps for the Clutch side. (See figure 4 for optional Cobra Light Bar installation, or to move Turn Signals forward to mount Lowers closer to the windshield.) 7. Once both windshield brackets are in place and all the new bolts are in place, Tighten all bolts. Re-install the chrome Turn Signal Bar cover. (Leave the chrome cover off if you use the alternate installation for Light Bar or Lowers). Re-Install the Headlight lens. 8. Loosen the (4) anchor bolts on the side of the windshield brackets. Slip the windshield mounting plates onto the brackets starting with the upper slot first then slip the bottom slot in. Adjust height, angle and tighten all bolts. This is a quick change kit. ALWAYS tighten all mounting bolts after removing or installing the windshield

Incoming search terms:

HARLEY DAVIDSON CHROME FORK COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
INSTALLATION OF KIT 66440-05 1. Kit 66440-05 , Loosen the fuel tank. Refer to FUEL TANK- PARTIAL REMOVAL in the appropriate section (carbureted or EFI Engine) of the Service Manual. 2. Disconnect the headlight connector from the main harness. 3. Start with one side and remove the screws fastening the trim strip and rear triple clamp cover. Remove trim strip and rear triple clamp cover. Repeat procedure for other side. 4. Remove the nut, washers, lockwashers and bolt holding the headlight housing to the tripletree. Retain all hardware for future use. Remove headlight housing. 5. Remove front panel. 6. See Figure 2. From kit, place front panel (1) into position. 7. Install headlight using the bolt, washer, lockwasher and nut removed earlier. Tighten fastener. Refer to your service manual for torque specifications and headlight alignment procedures. 8. Insert headlight wiring through hole (2) in front panel and connect wiring to main electrical harness. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 9. Install fuel tank. Refer to FUEL TANK-PARTIAL REMOVAL in the appropriate section (carbureted or EFI Engine) of your Service Manual. 10. Start with the left side and install the chrome rear triple clamp cover (4), and trim strip using screws removed earlier. Tighten fasteners. 11. Install the headlight switch thru switch hole (5) removed earlier. 12. Install the chrome right side rear triple clamp cover (3) and trim strip and tighten fasteners

2000 YAMAHA YZF-R1 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
CABLE ROUTING SPEC AProperly insert the meter assembly coupler and rubber boot into the meter assembly. BRoute the meter assembly lead through the left side of the headlight housing. CThe speedometer lead with not be tighten. DInstall the headlight relays onto the headlight housing bridge. EConnect to the right front turn signal connectors. FRoute the turn signal leads upper the headlight housing boss. 1 Clutch cable 2 Left handlebar switch lead 3 Starter cable 4 Main switch lead 5 Steering cover EB206000 CABLE ROUTING -21- NRoute the thermo switch/temperature sender sub- wire harness to the outside of the radiator cap. ORoute the right handlebar switch lead behind the throttle cables. Do not cross the throttle cables and the right handlebar switch lead. PRoute the right handlebar switch lead in front of the throttle cables. GFasten the headlight lead with a plastic clamp at white tape mark. HFasten the wire harness to the headlight housing boss with a plastic locking tie. IRoute the headlight lead through the plastic guide. JRoute the throttle cable to the front side of the brake hose. KRoute the clutch cable behind the front fork leg. LMake sure that the horn leads face out. MRoute the throttle cables and right handlebar switch lead between the lower bracket and steering cover. CABLE ROUTING SPEC -22- CRoute the rollover-valve-to-fuel-tank hose to the inside of the fuel hose (California only). DRoute the coolant reservoir breather hose over the timing chain tensioner. EInsert the plastic clip through the hole in the plastic frame panel and then fasten the wire harness and coolant reservoir breather hose with it. FRoute the clutch cable between the radiator bracket and frame and in front of the thermostat assembly breather hose. GRoute the clutch cable to the inside of the radiator inlet hose. HInsert the plastic clamp into the hole in the coolant reservoir’s tab

Incoming search terms: