how to check engine oil level for forklift

You search Auto repair manual PDF how to check engine oil level for forklift, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to check engine oil level for forklift Direct Download speed 5282 Kb/s

  how to check engine oil level for forklift Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL OIL COOLER KIT WITH CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models

Incoming search terms:

HARLEY DAVIDSON LCD OIL TEMPERATURE/ LEVEL DIPSTICK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
LCD DIPSTICK INSTALLATION 1. Remove the original equipment (OE) dipstick from the filler neck. 2. Non-threaded Dipsticks: Lightly oil the O-ring on the new LCD dipstick. Orient the dipstick so that the display window is horizontal and readable from left to right, with the Bar and Shield logo to the left (towards the rear of the motorcycle). Push the dipstick straight into the filler neck until it seats. 3. For threaded dipsticks: Lightly oil O-ring and screw into the transmission like OE dipstick. If the orientation of the display is unsatisfactory when fully seated, refer to Adjusting the Display Angle later in these instructions. NOTE To be sure of correct readings, the dipstick MUST seat firmly against the flange. LCD DIPSTICK USE AND CARE Removing the Dipstick The dipstick assembly must be removed from the filler neck to add oil or to service the internal battery. Displaying the Oil Temperature and Level See Figure 1. Press and release the rubber button on the front face to display the temperature of the oil in the oil tank in degrees Fahrenheit (°F), and the oil level. The display will automatically shut off after approximately ten seconds. Do not overfill oil tank. Doing so can result in oil carryover to the air cleaner leading to equipment damage and/or equipment malfunction. (00190a) NOTES Oil level cannot be accurately measured: • on a cold engine • with the motorcycle upright • with the engine running NOTE Oil level on 2000 through 2004 Softail models with the original dipstick is checked with the motorcycle standing upright (not leaning on the jiffy stand). THIS IS NOT THE CASE with the LCD oil temperature/level dipstick. For all 2000 and later Softail models, oil level inspection must be done with the motorcycle LEANING ON the jiffy stand, on level ground. For pre-ride oil level inspection: With the motorcycle on level ground, RESTING ON the jiffy stand : •The oil level should be as indicated in Figure 1, display 4 through 8 (bars showing oil level, and “COLD OIL” message followed by flashing oil temperature) when the engine is cold. DO NOT ADD OIL to bring the level to the FULL mark on the dipstick of a COLD engine. •If the oil level indicates as in display 9 (animated level bars, followed by an “888 NO SENSOR” code), the wires inside the dipstick may be disconnected or damaged. Refer to Replacing the Battery later in these instructions to separate the dipstick upper and lower assemblies. If the small plug next to the battery has become dislodged from the receptacle, plug it in. If a visible wire is damaged, a repair can be attempted. If no damage is visible, the dipstick is damaged internally and should be replaced. For oil level inspection at operating temperature: Ride the motorcycle until the engine is at normal operating temperature. Idle for 1-2 minutes with the motorcycle on level ground, RESTING ON the jiffy stand (except Softails) , turn the engine OFF.

Incoming search terms:

HONDA CT110 OWNERS MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
ENGINE OIL Engine Oil Level Check Check the engine oil level each day before riding the motorcycle. The level must be maintained between the upper (2) and lower (3) marks on the dipstick (1). 1. Start the engine and let it idle for a few minutes. 2. Stop the engine and hold the motorcycle in an upright position on firm, level ground. 3. After a few minutes, remove the oil filler cap/dipstick, wipe it clean, and reinsert the dipstick without screwing it in. The oil level should be between the upper and lower marks on the dipstick. 4. If required, add the specified oil up to the upper level mark. Do not overfill. 5. Reinstall the oil filler cap/dipstick, check for oil leaks. CAUTION Running the engine with insufficient oil can cause serious engine damage. TYRES Proper air pressure will provide maximum stability, riding comfort and tire life. Check tire pressure frequently and adjust if necessary. NOTE Tire pressure should be checked before you ride while the tyres are cold. Select the right replacement tire in accordance with the following specifications: Cold tire pressures kPa ( kg/cm2, psi ) Front: 175 ( 1.75, 25 ) Rear : 225 ( 2.25, 33 ) Tire size Front: 2.75 – 17 41P Rear : 2.75 – 17 41P Check the tires for cuts, embedded nails, ore other sharp objects. See your authorized Honda Dealer for replacement of damaged tires or punctured inner tubes OPERATION PRE-RIDE INSPECTION WARNING If the Pre-ride Inspection is not performed, serious damage or an accident may result. Inspect your motorcycle very day before you ride it. The items listed here will only take a few minutes to check, and in the long run they can save time, expense and possibly you life. 1. Engine oil level – add engine oil if required. Check for leaks. 2. Fuel level – fill the fuel tank when necessary. Check for leaks. 3. Brakes – check operation. Adjust free play if necessary. 4. Tyres – check condition and pressure. 5. Drive chain – check condition and slack. Adjust and lubricate if necessary. 6. Throttle – check for smooth opening and full closing in all steering positions. 7. Lights – check that headlight, tail/brake light, turn signals, indicators. 8. Engine stop switch – check for proper function. 9. Battery electrolyte – check the level and add if necessary Correct any discrepancy before you ride. Contact your authorized Honda dealer for assistance if you cannot correct the proble

Incoming search terms:

Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

Incoming search terms:

YAMAHA DT125RE/ X SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
OIL WARNING LIGHT CHECKING METHOD Main Switch “ON” Gears in “NEUTRAL” Oil warning indicator light does not come on Refeer to CHAPTER 8 “SIGNAL SYSTEM” Oil warning indicator light come on Shift into gear Oil warning indicator light does not come on Oil warning indicator light come on Supply engine oil Engine oil level and electrical circuit are OK 1 CHK ADJ TRANSMISSION OIL LEVEL INSPECTION/ TRANSMISSION OIL REPLACEMENT 3-11 TRANSMISSION OIL LEVEL INSPECTION 1. Inspect: •transmission oil level Oil level low **Add sufficient oil ******************************** Transmission oil level steps: •Place the machine on a level surface. •Warm up the engine for several minutes and stop it. •Visually check the oil level through the level window *. NOTE: •Check the oil level just one minute after stopping the engine. •The oil should e confirmed between maximum *and minimum *marks. •If the oil level is lower, add sufficient oil to raise it to the proper level. •Do not add any chemical additives. Transmission oil also lubricates the clutch and additives could cause clutch slippage. •Be sure no foreign material enters the crankcase. **************** **************** TRANSMISSION OIL REPLACEMENT 1. Warm up the engine for several minutes. 2. Place a container under the engine. 3. Remove: •oil filler cap * •drain pulg * drain transmission oil. NOTE: Drain the transmission oil with the motorcycle slightly inclined to the right. 4. Inspect: •gasket (Drain plug) •O-Ring (oil filter cap) Damage **Replace

Honda Ct110 Series Engine Oil Level Check

0

Filed Under (Honda) by admin on 17-09-2011

download
Engine Oil Level Check Check the engine oil level each day before riding the motorcycle. The level must be maintained between the upper (2) and lower (3) marks on the dipstick (1). 1. Start the engine and let it idle for a few minutes. 2. Stop the engine and hold the motorcycle in an upright position on firm, level ground. 3. After a few minutes, remove the oil filler cap/dipstick, wipe it clean, and reinsert the dipstick without screwing it in. The oil level should be between the upper and lower marks on the dipstick. 4. If required, add the specified oil up to the upper level mark. Do not overfill. 5. Reinstall the oil filler cap/dipstick, check for oil leaks.

Lambretta UNO50 Owners Manual

0

Filed Under (Lambretta) by admin on 25-11-2010

download
brakes: Inspect brake cables/hoses/linkage for correct mounting, chafing, leaks and damage. Check and adjust both front and rear brakes. If hydraulic, check fluid level and correct if necessary (DOT 4 fluid only). Engine: Check and correct the engine oil level. Fuel system: Check fuel tank, carburetor, fuel valve and all hoses for leaks. Throttle system: Check for correct throttle cable routing. Throttle operates smoothly and self-returns to idle from all handlebar positions. Wheels/tires: Check wheels, tires and valve stem for damage, etc. Check and adjust tire pressures. 11 Suspension: Check for smooth suspension operation. Lubricate all grease points using correct specification grease. Check for correct suspension adjustments. Inspect fork and shock seals for leaks. Steering: Check for smooth steering operation and handlebar bearings for proper adjustments. Electrical Systems: Check for correct function of all side, headlight (high/low beam) and taillights, turn indicators, brake lights, warning lights and instrument illumination. Check for correct horn operation. Check harnesses for correct routing. Check for correct function of starter lockout system. Check for correct engine stop switch operation. Check for correct function of the low oil warning light. (2 stroke only) Emission Systems: Check connections and hoses for routing and kinks.
12 Fastening hardware: Check front and rear axle nut and bolt torque. Check torque of drain plug and oil filter bolt. Check torque of all brake system nuts and bolts. Check torque of all steering system mounting hardware. Check torque of exhaust mounting hardware. Check torque of all remaining nuts, bolts & screws. Road test Front and rear brake operation. (approx. 10km): Check cold engine start performance. Evaluate performance, handling and braking. After road testing: Check hot engine starting. Check and adjust idle speed. Check for oil and fuel leaks. Make necessary adjustments and repair any defects seen or observed before, during and after test drive. Retest as necessary. Clean the vehicle prior to deliver

Incoming search terms:

HONDA CT110 OWNERS MANUAL Engine Oil Level Check

0

Filed Under (Honda) by admin on 10-11-2011

download
Check the engine oil level each day before riding the motorcycle. The level must be maintained between the upper (2) and lower (3) marks on the dipstick (1). 1. Start the engine and let it idle for a few minutes. 2. Stop the engine and hold the motorcycle in an upright position on firm, level ground. 3. After a few minutes, remove the oil filler cap/dipstick, wipe it clean, and reinsert the dipstick without screwing it in. The oil level should be between the upper and lower marks on the dipstick. 4. If required, add the specified oil up to the upper level mark. Do not overfill.
5. Reinstall the oil filler cap/dipstick, check for oil leaks

Oil Pressure Gauge Set Installation

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
7. See Figure 3-4 . Assemble banjo bolt (3), washer (4), OIL PRESSURE GAUGE (1) banjo fitting and second washer onto adapter and tighten snugly. 8. Temporarily secure oil pressure gauge and hose to motorcycle frame with cable straps. Make sure gauge and hose assembly do not interfere with normal operation of the vehicle. Start engine and ride motorcycle at least 20 miles (32 km) at or above 50 mph (80 km/h) to allow engine to reach operating temperature. a. At 2500 RPM, oil pressure will vary from 10-17 psi (69-117 kN/m2). b. At idle speed (950-1050 RPM), oil pressure will vary from 7-12 psi (48-83 kN/m2). NOTE For an accurate reading, engine oil should be at normal operating temperature: 230°F (110°C). 9. Stop engine. Remove OIL PRESSURE GAUGE assembly from oil pressure indicator lamp switch mounting hole in crankcase. Cut cable straps that you installed in step 8. above, and remove banjo bolt, gauge assembly, washers and adapter from vehicle. 10. See Figure 3-2 . Coat threads of oil pressure switch (2) with LOCTITE 565 HIGH PERFORMANCE PIPE SEALANT with TEFLON. Reinstall oil pressure switch. Using OIL PRESSURE SENDING UNIT WRENCH, tighten switch snugly. DO NOT OVERTIGHTEN. 11. Plug in connector [120] (3) by pushing elbow connector straight up onto stud on oil pressure switch. 12. Install voltage regulator caddy and attach DC output connector and neutral switch wiring harness to caddy. See 7.28 MAIN WIRING HARNESS . NOTE If an appreciable amount of oil leaked out when oil pressure switch was removed, it will have to be replaced with fresh oil. 13. Check oil level in oil tank. See 1.5 ENGINE OIL AND FILTER . Top off oil level if necessary. 14. Start engine and test oil pressure switch for proper operation. Check oil pressure switch for leaks.

Incoming search terms:

Triumph Oil Filter Mount installation

0

Filed Under (Triumph) by admin on 29-10-2010

download
The Norton filter adapter is then bolted to the rear piece, oil hoses are added, an oil filter is screwed into place, and the assembly is offered to the bike. With the bike supported by straps up on a lift, it will be easy to loosely mount the front clamp section in place and slide the whole assembly up the frame tube. In order to miss the center stand, the filter will need to be as high as possible without the grease nipple striking the top of the adapter. As it ends up, there is “sweet spot” where both the nipple and the stand miss the oil filter by about an 1/8 inch. Tighten the mount down when you find that place. I found that the Norton filter adapter is best plumbed using 5/16 ID black neoprene fuel hose. The spigots on the adapter are 3/8 inch, but it is better to stretch the hose over these that to use easier fitting 3/8 ID hose and then try to shrink it onto the Triumph’s smaller metal oil lines. There will simply be fewer oil leaks using the smaller hose. Be sure that you plumb the filter into the oil line that returns engine oil back to the oil tank. The Triumph oil pump cannot be counted on to create enough vacuum to suction highly viscous motor oil through a very fine filter during cool temperatures. Trying to place the filter on the oil line feeding the engine will quickly result in massive engine damage. It is always better to have the oil pump pushing oil through the filter, and the only way to have RF Whatley, Suwanee, GA 5 Jan 2008 that is to use the return oil line. On all “unit-construction” Triumph engines, the rear-most oil port is the engine oil return. Other Notes • It is generally considered that adding an oil filter will at least quadruple the life of a British motorcycle engine. These motors, which were for the most part perfected in the 1950′s, were designed to run on the older non-detergent oils. In the original design, the oil tank was the oil filter since all particulate debris in the oil settled to the bottom of the oil tank as sediment. All modern engine oils are high-detergent and tend to inhibit the formation of sediment. Therefore most of the fine abrasive in the engine oil continues to circulate unless a filter is added.

Incoming search terms: