how to check the timing on 93 harley ultra classic

You search Auto repair manual PDF how to check the timing on 93 harley ultra classic, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to check the timing on 93 harley ultra classic Direct Download speed 5282 Kb/s

  how to check the timing on 93 harley ultra classic Full Version speed 6162 Kb/s



POLINI X1 GENERAL INFORMATION AND SPECIFICATIONS

0

Filed Under (Polini) by admin on 02-12-2010

download
Air cleaner – Clean and reoil daily or after each moto to prevent motor failure and reduced performance. Transmission oil – change after every race, or at end of riding day. Chain – check tension and lubricate before every ride, adjust or replace as needed. Reoil after riding in damp conditions. Clutch – disassemble and clean clutch assembly frequently, every 2-3 races at least. Inspect kickstarter gears at this time. Ignition cover – remove cover and wipe dry after each ride or after washing bike to remove condensation. Piston rings – replace as often as every 3-5 races with expert rider, less often with less aggressive riders. Piston, pin, rod bearing & circlips – replace as often as every 8-10 races with expert rider, less often with less aggressive riders. Coolant – change yearly, make sure there is at least a 50/50 mixture of antifreeze if freezing temperatures are possible. Steering bearings – Check daily for looseness or play. Adjust and regrease as needed. Swingarm – Check often for looseness. Regrease several times a year. Replace bushings if any play is evident. Sprockets – check for worn or curved teeth each time chain is adjusted. Chain roller& wear pads – check roller for free rotation when checking chain. Make sure roller is not bent or damaged. Check chain wear strips on swingarm and chain guide frequently. Replace as needed to prevent chain from damaging motorcycle. Spokes – Check after each race or after each day of riding for looseness or damage. Wheels & tires – check wheels after each race for dents, cracks or other damage. Check tires for cuts, damage or wear. Check tire pressure daily and adjust for riding conditions. Shock – Check shaft area daily for signs of oil leakage or damage. Check swingarm and shock bushings for looseness. Forks – Check forks daily for leaking oil or damage to tubes. Make sure forks are not twisted check for smooth operation. Spark plug – check sparkplug color and condition after each race or end of riding day. Adjust jetting to keep plug from fouling or overheating. Silencer – If bike seems to be getting louder, replace packing and decarbonize inner tube. Expansion pipe – check daily for large dents, damage or leakage. Remove carbon from headpipe when pipe is removed. Have large dents fixed, or any dents within 8″ of the cylinder. Replace o-rings on pipe as needed to maintain a good seal. Footpegs – check daily for proper operation, pegs should spring back into place. Make sure pegs are not bent or overly dull. Handlebars – check bars after any crash for bending. Look for cracks near bar clamps. Replace bars that have been straightened more than 2 or three times, or if bar is badly bent. Aweakened bar can snap suddenly causing injury to rider. Throttle – check throttle for proper operation each time before bike is started. Remove and clean inside of grip and bar as needed. Grips – check grips daily for wear or looseness. Replace as needed. Use grip glue & safety wire to help hold grips in position. Calipers & pads – check pad wear and caliper function daily or after each race. Replace pads and clean calipers as needed. Brake lever – check lever daily for damage or wear. Make sure lever is at proper angle for both seated and standing positions. Leave lever clamp loose enough to allow clamp to rotate during crash rather than breaking lever. Check and adjust freeplay as needed. Brake pedal – Check pedal daily for damage and proper freeplay. Adjust rear caliper as needed. Reeds – Remove and inspect reed block during every ring change. Check reeds for signs of wear, fraying and cracking. Make sure reeds sit flat and seal well. Replace at any sign of wear or damage or at least once a year, more often for expert riders. Nuts & bolts – Check all nuts and bolts regularly. Make sure to check engine mounting bolts and swingarm bolt frequently

Incoming search terms:

Lambretta UNO50 Owners Manual

0

Filed Under (Lambretta) by admin on 25-11-2010

download
brakes: Inspect brake cables/hoses/linkage for correct mounting, chafing, leaks and damage. Check and adjust both front and rear brakes. If hydraulic, check fluid level and correct if necessary (DOT 4 fluid only). Engine: Check and correct the engine oil level. Fuel system: Check fuel tank, carburetor, fuel valve and all hoses for leaks. Throttle system: Check for correct throttle cable routing. Throttle operates smoothly and self-returns to idle from all handlebar positions. Wheels/tires: Check wheels, tires and valve stem for damage, etc. Check and adjust tire pressures. 11 Suspension: Check for smooth suspension operation. Lubricate all grease points using correct specification grease. Check for correct suspension adjustments. Inspect fork and shock seals for leaks. Steering: Check for smooth steering operation and handlebar bearings for proper adjustments. Electrical Systems: Check for correct function of all side, headlight (high/low beam) and taillights, turn indicators, brake lights, warning lights and instrument illumination. Check for correct horn operation. Check harnesses for correct routing. Check for correct function of starter lockout system. Check for correct engine stop switch operation. Check for correct function of the low oil warning light. (2 stroke only) Emission Systems: Check connections and hoses for routing and kinks.
12 Fastening hardware: Check front and rear axle nut and bolt torque. Check torque of drain plug and oil filter bolt. Check torque of all brake system nuts and bolts. Check torque of all steering system mounting hardware. Check torque of exhaust mounting hardware. Check torque of all remaining nuts, bolts & screws. Road test Front and rear brake operation. (approx. 10km): Check cold engine start performance. Evaluate performance, handling and braking. After road testing: Check hot engine starting. Check and adjust idle speed. Check for oil and fuel leaks. Make necessary adjustments and repair any defects seen or observed before, during and after test drive. Retest as necessary. Clean the vehicle prior to deliver

HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

HONDA CT110 OWNERS MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
ENGINE OIL Engine Oil Level Check Check the engine oil level each day before riding the motorcycle. The level must be maintained between the upper (2) and lower (3) marks on the dipstick (1). 1. Start the engine and let it idle for a few minutes. 2. Stop the engine and hold the motorcycle in an upright position on firm, level ground. 3. After a few minutes, remove the oil filler cap/dipstick, wipe it clean, and reinsert the dipstick without screwing it in. The oil level should be between the upper and lower marks on the dipstick. 4. If required, add the specified oil up to the upper level mark. Do not overfill. 5. Reinstall the oil filler cap/dipstick, check for oil leaks. CAUTION Running the engine with insufficient oil can cause serious engine damage. TYRES Proper air pressure will provide maximum stability, riding comfort and tire life. Check tire pressure frequently and adjust if necessary. NOTE Tire pressure should be checked before you ride while the tyres are cold. Select the right replacement tire in accordance with the following specifications: Cold tire pressures kPa ( kg/cm2, psi ) Front: 175 ( 1.75, 25 ) Rear : 225 ( 2.25, 33 ) Tire size Front: 2.75 – 17 41P Rear : 2.75 – 17 41P Check the tires for cuts, embedded nails, ore other sharp objects. See your authorized Honda Dealer for replacement of damaged tires or punctured inner tubes OPERATION PRE-RIDE INSPECTION WARNING If the Pre-ride Inspection is not performed, serious damage or an accident may result. Inspect your motorcycle very day before you ride it. The items listed here will only take a few minutes to check, and in the long run they can save time, expense and possibly you life. 1. Engine oil level – add engine oil if required. Check for leaks. 2. Fuel level – fill the fuel tank when necessary. Check for leaks. 3. Brakes – check operation. Adjust free play if necessary. 4. Tyres – check condition and pressure. 5. Drive chain – check condition and slack. Adjust and lubricate if necessary. 6. Throttle – check for smooth opening and full closing in all steering positions. 7. Lights – check that headlight, tail/brake light, turn signals, indicators. 8. Engine stop switch – check for proper function. 9. Battery electrolyte – check the level and add if necessary Correct any discrepancy before you ride. Contact your authorized Honda dealer for assistance if you cannot correct the proble

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

Incoming search terms:

2000 Harley-Davidson FLHRCI Road King Classic

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
the Road King® Classic is a motorcycle with enough traditional styling to drop jaws throughout the continent. The Road King® Classic boasts laced wheels, fat white-walls and gorgeous leather saddlebags with hard inserts so they keep their shape across the long miles. Slightly narrower new handlebars provide improved ergonomics. Fender tips, tank and seat valance all boast a metal emblem. The model is available with a fuel-injected, chrome-and-black Harley- Davidson® Twin Cam 88 engine. Specifications: Engine Type: 1449 cc, 4-Stroke, Air Cooled, V-Twin Engine Bore and Stroke: 95.3 mm x 101.6 mm Valves 2 valves/cylinder Claimed Horsepower: 67 hp (50 kW) @ 5200 rpm Maximum Torque: 110 Nm (81.1 ft. lbs) @ 3100 rpm Transmission type: 5 speed Final Drive: Belt Tire – Front: 130/90-16 Tire – Rear: 130/90-16 Brakes – Front: dual 292 mm discs with 4-piston calipers Brakes – Rear: single 292 mm disc with 4-piston calipers

Incoming search terms: