how to connect a gl1500 cb radio installation instruction

You search Auto repair manual PDF how to connect a gl1500 cb radio installation instruction, if there are search results will appear below. If search results do not exist, please search by others keyword.

Harley-Davidson MOBILE RADIO & CONTROL UNIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-03-2012

download
Installation of the ORION mobile radio and control unit consists of: •Assembling and installing the weather resistant motorcycle case assembly, including the adapter bracket, case/antenna mounting bracket, and bottom case (previously assembled) to the motorcycle mounting bracket (user supplied). •Installing the radio in the radio mounting bracket located inside the weather-resistant case, •Installing the control unit, microphone, and speaker •Installing the antenna •Routing the power, control, and option cables •Connecting all cables including: power, control, and option cables. •Installing the Headset Option •Operational check All mounting hardware consists of stainless steel screws, locknuts, nuts, and lockwashers to resist corrosion. TOOLS REQUIRED •Socket wrench set U.S./metric with 3″ extender •Open end wrench, adjustable •Wire clippers •TORX BIT set, small metric 13
EQUIPMENT INSTALLATION Assembling & Installing The Weather Resistant Case As- sembly The motorcycle Weather Resistant Case Assembly may be installed on almost any motorcycle. Installation instructions provided here include information for the Harley-Davidson Dyna and Road King models and the Kawasaki K1000. Figure 5 illustrates installation on Harley-Davidson motorcycles while Figure 6 illustrates installation on a Kawasaki K1000. Refer to these diagrams during installation. Installation on other motorcycles is at the discretion of the installer. Harley-Davidson Installation 1. Unpack the weather resistant motorcycle case, remove the key taped to the top cover and open the case. 2. Refer to Figure 5 and verify that all components shown in the diagram are available. 3. Mount the adapter bracket onto the Dyna or Road King radio mounting bracket (user supplied) using the 1/4-20 x 5/8 screws provided

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

HARLEY DAVIDSON FLHT RADIO AND GAUGE FACEPLATE TRIM INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
This kit fits 1996 and later FLHT models. Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE The instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents Table 1. Kit Contents Part Number Description 74612-06 Radio and gauge faceplate trim There are no Service Parts available with this kit. INSTALLATION NOTE Mounting surface of faceplate trim must be above 60°F (16°C), or the trim may not stay attached. 1. Using a 50:50 isopropyl alcohol/water solution, thoroughly clean the surface where the faceplate trim will be installed. Do not clean with denatured alcohol, mineral spirits, or other solvent products, or damage to the radio may occur. (00411b) 2. Allow the surface to dry completely before continuing to install kit. 3. Test the fit of the faceplate trim prior to removing adhesive backing. 4. Remove the adhesive backing from the back of the faceplate trim. 5. See Figure 1. Install the faceplate trim, locating it upward as far as possible. This position will align the opening in the faceplate trim with the indicator lights. NOTE If you do not position the faceplate trim properly, this may prevent proper clearances between the CD door and trim for 2006 and later models. 6. Let the adhesive cure for at least 24 hours at no less than 60°F (16°C). is01435 Figure 1. Indicator lights properly aligned through faceplate NOTE For models earlier than 2006, the installation is complete after the faceplate trim is installed.

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

2001 HONDA GL1800/ A Radio Muting Improvement

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Place the faulty radio in the same box in which the exchange radio was sent. THE FAULTY RADIO (CORE) MUST BE RETURNED IN THE SAME BOX IN WHICH THE EXCHANGE RADIO WAS SHIPPED. These boxes are identified by the label shown below which is printed on the inside of the lid. 2. Fill out the pre-printed FedEx airbill that came in the box with the exchange radio. The airbill should have the following address preprinted on it: AHM Remanufactured Parts c/o NK Parts Industries Inc./West 2640 Campbell Rd. Sidney, OH 45365-8836 • Do not use an ordinary FedEx airbill. The pre- addressed airbill has a special account number on it for the exchange program. If you need more airbills, call the Radio Order Desk toll free, not your assigned Parts Center . • Write your dealer number and the warranty claim number in the area shown in the sample airbill ffix the FedEx Airbill to the outside of the box. Radios sent in a box not bearing the correct FedEx airbill will not be accepted for reimbursement under this program. 4. Enclose a copy of the HONDANET for Windows warranty claim in the box. If the claim form is incomplete or not in the box, the faulty radio will be returned to your dealership. 5. Ship the faulty radio to the preprinted address on the airbill. NOTE: Do not ship the faulty radio to the manufacturer or the Warranty Parts Inspection (WPI) Center. 6. For your records, on the repair order include the following: • warranty claim number • original part number • FedEx airbill number When the faulty radio is received, a core credit will be posted to your dealership’s Balance Forward Account. The credit can be identified by the claim number + “CORE” (e.g., 12345/CORE). REMEMBER: A copy of the HONDANET for Windows warranty claim must be included in the box. RETURNING THE FAULTY RADIO The faulty radio must be returned within 20 days of

Related Item : 2003 tacoma stereo removal (1)91734-06 (1)stereo upgrade for victory cross country (1)