how to decat head pipe on harley

You search Auto repair manual PDF how to decat head pipe on harley, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to decat head pipe on harley Direct Download speed 5282 Kb/s

  how to decat head pipe on harley Full Version speed 6162 Kb/s



YAMAHA VIRAGO 700/ 1100 2 into 2 EXHAUST SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the slip joint clamp on the front and rear head pipe, which are located at the muffler box. 2. Remove the two nuts that hold the front head pipe to the engine. Slip the head pipe out of the muffler box and set it aside. Note: Do not remove the rear head pipe, it has been incorporated in the design of the new exhaust system. 3. Remove the muffler box mounting bolt located in front of the passenger foot rest on the left side. 4. Remove two bolts from the right passenger foot rest assembly and set the foot rest aside. 5. Slide the muffler box off of the rear head pipe and set it aside. 6. Replace the muffler box mounting bolt (from step #3) using the washer and nut (supplied) on the back side. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Attach the mounting bar to the motorcycle frame behind the right passenger foot rest. Align the two holes in the largest bracket on the mounting bar with the two holes on the frame, be sure the bend in the mounting bar is pointing to the center of the motorcycle. 2. Install the round steel spacer (supplied) to the rear most hole in the bracket. 3. Attach the foot rest using the two 8mm x 1.25 x 25mm bolts (supplied). 4. Slide the new exhaust flange (supplied) onto the front head pipe. 5. Install the two heat shields to the front head pipe using the four hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the heat shields onto the front head pipe. Note: Be sure the bend in the heat shield matches the bend in the head pipe exactly. Wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 6. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 7. Slide a chrome pinch clamp (supplied) onto the expanded end of the new rear head pipe. Install a 3/8″ x 1″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Repeat this step on the inlet end of each muffler using the two muffler clamps with 5/16″ x 1 1/4″ bolts (hardware supplied) but leave the clamp loose at this time. 8. Slip the new rear head pipe with the heat shield attached, over the stock rear pipe and gasket, but leave the clamp loose at this time. 9. Install the front head pipe, with the heat shield attached and stock gasket in place, to the front cylinder using the stock nuts, leave them loose at this time

Incoming search terms:

HARLEY DAVIDSON DYNA LongShot Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove both front and rear head pipe clamp bolts. 4. Remove the entire exhaust system and set it aside. 5. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips. 6. Remove the rear head pipe clamp bracket from the transmission cover. Save the bolts, two will be reused. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Locate the muffler mounting bracket (stamped 239). Mount the bracket to the engine case, to the rear of the transmission cover using the two stock bolts. Refer to figure 1. Tighten the bolts at this time. Install the mounting bar (supplied) to the transmission housing using the stock hardware. Refer to figure 1 . Note: The mounting bracket should mount flatagainst the transmission housing. Some motorcycles use a stud to mount the stock rear head pipe clamp, be sure to remove the stud from the transmission housing and replace it when mounting the bracket, this will insure that the bracket is flat against the housing. 2. Locate the muffler clamp bracket (stamped 240). Install the bracket to the outside of bracket 239, using the 5/16″x 1 1/4″ bolt and 5/16″ flat washer (supplied). Refer to figure 1. Leave the bracket loose, it will be adjusted later. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the circlips and flanges from the stock system onto both the new head pipes. 5. Slide the new pipe clamp (supplied) onto the muffler end of the front head pipe. Position the clamp in the approximate mounting location on the pipe. 6. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the rear head pipe.

Incoming search terms:

Yamaha Road Star 1600/ 1700 Exhaust kit bill of materials Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove left side cover, by removing allen bolt as shown (Fig 1). Once bolt is removed, push cover to motor and push back carefully to your upper body. Figure 1 2. Once left side cover is removed, remove 6mm bolt to opposite side cover as shown (Fig. 2). Also remove allen bolt on right side as shown (Fig 3) and remove carefully . Figure 2 Figure 3 . Remove two allen bolts to the muffler bracket, and also loosen hose clamp to bottom head pipe. (Fig 4 & 5) Figure 4 Figure 5 4. Remove bolt next to rear O/2 sensor bracket as shown (Fig 6), also remove Phillips head bolt from O/2 bracket and slide O/2 sensor off bracket as shown (Fig 7). Once bracket is removed mount just bracket on with Phillips head bolt back on. Figure Figure 7 5. Disconnect O/2 by using a pick on inside switch on opposite side of O/2 bracket. With pick on inside push to you and unplug. (Fig 8 & 9) Figure 8 Figure 9 6. Remove two socket cap nuts from rear head pipe flange as shown (Fig 10). Once removed, remove both mufflers and rear head pipe carefully. Slide muffler back and shift rear head pipe to you. (Fig 11) Figure 10 Figure 11 7. Slide wire off bracket from the front O/2 sensor as shown (Fig 12). Also use pick to remove O/2 sensor, push to you and unplug. Figure 12 Figure 13
8. Remove two allen bolts from foot rest/ brake to give you access to head pipe. (Fig 14) Figure 14 9. Remove two allen socket cap nuts off front head flange and remove head pipe. (Fig 15) Figure 15 10. Remove stock muffler bracket by removing two alien bolts as shown (Fig 16). Also remove bolt that holds stock bracket to the brake line (Fig 17). Once that is done remove brake line from caliper and slide though muffler bracket and re-install. Figure 16 Figure 17
Assembly 11. Remove O/2 sensor from stock pipe and install O/2 sensor in Roadhouse front head pipe and mount front head pipe with stock socket cap nuts on bike as shown. (Fig 18 & 19) Figure 18 Figure 19 12. Mount rear head pipe as shown (Fig 20), including stock socket cap nuts. Also mount y-collector with rear head pipe. Y-collector must slide into front head pipe in one. Install Roadhouse O/2 sensor wire lead from hardware kit into y-collector. (Fig 21) Figure 20 Figure 21

Incoming search terms:

HARLEY DAVIDSON Dresser 2-1 Pro Pipe HS Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place motorcycle on side stand. Remove both left and right saddlebags. 2. Loosen pinch clamp bolt on front end of each muffler. Note : On older model Dresser exhaust, spread clamps just enough to remove them. 3. Remove two 5/16″ bolts holding the left and right mufflers to the saddlebag supports. 4. Remove stock mufflers and set them aside. Note : It may be necessary to use a penetrating lubricant on slip joint between muffler and head pipe. 5. Loosen heatshield clamps on both front and rear head pipes. 6. Loosen the left rear head pipe mounting clamp located behind the rear cylinder. Remove the section of head pipe that connects to left side muffler. 7. Remove 3/8″ bolt from the head pipe clamp that secures front head pipe to the transmission bracket. 8. Remove right hand floor board. 9. Remove flange nuts that secure each head pipe to cylinder head. Carefully remove the head pipes and set them aside. 10. Carefully remove flanges and circlips (save) from the stock exhaust system using snapring pliers. Note: Replace bent or damaged circlips. 11. Remove stock transmission bracket. To access standard transmission bracket, first remove oil dip stick cover and clutch release cover. Refer to figure 1. Note : If motorcycle is resting in a near vertical position, engine/transmission oil must be drained completely before removing covers. Loosen and remove four allen bolts and stock transmission bracket. (save)

Harley davidson American Classic Straights on a 1988-2001 VLX 600 Shadow Installation Instructions

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system.
1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install nut strip into slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — DO NOT TIGHTEN NUTS! 8. Install nut strip into slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks.

Incoming search terms:

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

Incoming search terms:

Harley-Davidson DYNA Straightshot Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove both front and rear head pipe clamp bolts. 4. Remove the entire exhaust system and set it aside. 5. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips. 6. Remove the rear head pipe clamp bracket from the transmission cover. Remove any studs and bolts necessary and set aside to use when installing the new muffler mounting bar to the transmission housing. Refer to figure 1. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the mounting bar (supplied) to the transmission housing using the stock hardware. Refer to figure 1 . Note: The mounting bracket should mount flatagainst the transmission housing. Some motorcycles use a stud to mount the stock rear head pipe clamp, be sure to remove the stud from the transmission housing and replace it when mounting the bracket, this will insure that the bracket is flat against the housing. 2. Check condition of stock exhaust gaskets. Replace if worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets, part number 17048-98. 3. Install the circlips and flanges from the stock system onto both new head pipes. 4. Slide one pipe clamp (supplied) onto the front head pipe. Position the clamp in the approximate location on the tube where it mounts to the engine. 5. Slide one pipe clamp (supplied) onto the rear head pipe. Position the clamp in the approximate location on the tube where it mounts to the top hole in the mounting bar bracket. Refer to figure 1. 6. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DUALS AND SLIP ONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
1. Attach mounting brackets 430-P on the left side and 431-P on the right side of the frame using two 3/8″ x 3/4″ fl ange head bolts on each one (supplied)(Figure 1). If equipped, plastic plugs must be removed. 2. Remove left foot peg and attach support bracket 428-P (Figure 1) using the stock bolt. Discard spacer if equipped. Do not tighten at this time. NOTE: On FLSTN models the passenger footpeg bracket should be removed. 3. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 2). 4. Lay front head pipe, rear head pipe and muffl ers into their heat shields. 5. Install #20 hose clamps on heat shields and #28 on muffl er heat shields by feeding tail end of clamps into heat shield clips (Figure 2). Take note of clamp screw head direction (Figure 3). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 6. Install exhaust port fl anges and circlips from stock system onto head pipes (Figure 4). 7. Apply a small amount of anti-seize compound to the threads of one of the oxygen sensors and install it into front head pipe. NOTE: Be careful not to get anti-seize on sensor tip, it may affect sensor function. Do not install rear sensor at this time. 8. Disconnect front mount on shift lever rod to allow installation of rear head pipe (Figure 7). 9. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 10. Remove ignition coil cover to have open access to install rear sensor. 11. Install rear sensor using same instructions as step 7. Feed connector for rear oxygen sensor through frame and under the oil tank. Plug the sensor into stock wiring connector. 12. Slide a #59 T-bolt clamp (supplied) onto slotted end of left pipe. Slide slotted end onto head pipe tail (Figure 5). Align pipe with bracket 428-P previously installed in step 2. Install a #60 T-bolt clamp (supplied) by removing the nut and feeding the tail end through bracket hole (Figures 1 and 5). NOTE: Orient the clamp so that you can

Incoming search terms:

Harley-Davidson V-Rod Destroyer Indy Series Exhaust REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
STOCK EXHAUST SYSTEM REMOVAL (DESTROYER) 1. Remove both collector bolts. 2. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 3. If the Racepak is installed, remove both O2 and EGT sensors from the front and rear head pipes. 4. Carefully remove complete exhaust from the motorcycle. STOCK EXHAUST SYSTEM REMOVAL (V-ROD) 5. Loosen clamp bolt at front of the collector using a 13mm socket. 6. Remove muffler bracket bolt using a 13mm wrench. 7. Carefully remove muffler and collector assembly from motorcycle. 8. Remove nuts from both front and rear exhaust cylinder head flanges using a 13mm socket. 9. Carefully remove head pipes from motorcycle. 10. Remove the stock exhaust flanges and circlips from both the front and rear head pipes. If the circlips are bent or twisted they should be replaced, Harley-Davidson part number #65045-01 We also recommend replacing the stock exhaust gaskets, Harley-Davidson part number #65109-01 INDY SERIES EXHAUST SYSTEM INSTALLATION 1. Identify front head pipe #7-8002. Install the stock flange and circlip. Install the exhaust gasket and front header pipe, leaving the flange nuts hand tight. 2. Repeat the above step for the rear head pipe #7-8006. 3. Slip the megaphone/collector assembly onto the head pipes, secure with the four springs supplied using the spring puller tool. 4. Rotate the exhaust so there is adequate clearance in all places. 5. Tighten the cylinder head flange nuts for both the front and rear head pipes. 6. Tighten both the EGT and O2 plugs on the front and rear head pipes. 7. Clean all fingerprints from the exhaust using a contact cleaner (or other non flammable cleaner). Fingerprints will leave stains on the pipe once the motorcycle is started. 8. You are now ready to start the motorcycle.

Incoming search terms:

Harley Davidson Sportster Straightshots HS Slip-on Exhaust system

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Loosen, but do not remove, the two head pipe mounting nuts from each flange located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Loosen the clamp holding the mufflers onto the head pipes. Page 1 of 4 D480IN Rev. 1.0 Sportster Straightshots HS Slip-on Exhaust system Part #16819 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 1/2″ combination wrench 3/8″ drive ratchet and 9″ extension 9/16″ and 1/2″ sockets 5/16″ Nutdriver/flat blade screwdriver 5. Remove the two bolts from each muffler which attach the mufflers to the mounting bar. 6. Remove the mufflers by sliding them off the head pipes. 7. Remove the clamp from the nose of each muffler (these will be re-used when installing the new mufflers). 8. Remove the gaskets from the crossover ports on the stock mufflers. Inspect the gaskets and replace if damaged or worn (H-D part #65927-00). 9. Install crossover gaskets onto mounting bar on motorcycle. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Remove mufflers and heat shields from protective packaging. 2. Slide the nut plate inside the bracket that is welded to the backside of each muffler body and attach the muffler bodies to the mounting brackets (stamped 379-P) using four 5/16″ x 5/8″ flange head bolts (supplied). Leave them loose at this time (Figure 1). 3. Slide stock exhaust clamp onto nose of each muffler. 4. Slide mufflers onto head pipes and align crossover port with gasket on mounting bar (Figure 2). Press into place on gasket. 5. Attach the muffler brackets to the stock mounting bar using four 5/16″ x 3/4″ hex head bolts, washers, and nuts (supplied). Leave them loose at this time (Figure 3). 6. Tighten cylinder port exhaust flange nuts on front and rear cylinders. 7. Install and tighten the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 8. Align muffler and bracket so they sit level. Tighten the muffler mounting bolts and the bracket mounting bolts. 9. Tighten the clamp holding the muffler onto the head pipe.

Incoming search terms:

Incoming search terms: