how to dismantle center stand for fz16

You search Auto repair manual PDF how to dismantle center stand for fz16, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to dismantle center stand for fz16 Direct Download speed 5282 Kb/s

  how to dismantle center stand for fz16 Full Version speed 6162 Kb/s



Harley-Davidson touring bikes WHEELDOCK EZ-UP Center Stand Installation Instructions

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common problems: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter.

Incoming search terms:

Harley-Davidson The WHEELDOCK EZ-UP Center Stand Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common questions: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter

Incoming search terms:

HARLEY DAVIDSON CHROME DISPLAY STAND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and disconnect the battery negative (-) cable or remove the main fuse. NOTE Make sure that the cutout (B) of the strap (3) is oriented to the rear of the motorcycle after installation. 2. See Figure 2. Install strap (3) and weld nut (4) to the frame in the locations shown. 3. Position the center display stand over the mounting holes under the frame, oriented so that the skid plate faces for- ward. 4. Apply a small amount of Loctite 271 – Red to the two long screws (1) and secure the rear of the display stand to the frame by installing the two screw to the strap. 5. Apply a small amount of Loctite 271 – Red to the short screw (2) and secure the front of the display stand to the frame by installing the screw to the weld nut. 6. Tighten screws to 60-96 in-lbs (7-11 Nm) . 7. Refer to the service manual and connect the battery cables or install the main fuse. 1 2 is05370 1. Flange side 2. Flat side Figure 1. Chrome Display Stand Foot Orientation ADJUSTING THE DISPLAY STAND The left and right feet of the display stand are independently adjustable to vertically level the vehicle with the display stand extended. To adjust the display stand: NOTE The display stand can be adjusted with rear tire to ground contact or with rear tire off the ground. With the rear tire to ground contact adjustment, the rear wheel is on the ground but enough weight is on the display stand legs to make the motorcycle stable from side-to-side and front-to-back. Using the display stand to center the motorcycle will require effort. With the rear tire off the ground adjustment, the rear tire clears the ground so tire can be rotated for cleaning or maintenance purposes. Using the display stand to lift rear tire off the ground will require more effort. Do not center the vehicle with someone on the vehicle. To reduce effort, remove stored items from saddlebags, if equipped

Incoming search terms:

HONDA 1100 ACE, AERO AND SABRE CENTERSTAND INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-12-2010

download
Relocation of Regulator. Laying under the right side of the motorcycle, locate the voltage regulator. (finned aluminum box-approximately 3″x 4″) Note: See photo #1 – regulator already relocated. Remove the (2) 10 mm bolts attaching the regulator to the frame. Attach the bracket supplied to the regulator as shown. Using the original bolts, attach the regulator and bracket assembly to the frame as shown in photo #1 using the two 10 mm bolts supplied. Clamping Centerstand to Frame . Notice the centerstand is shipped with (2) white plastic washers. Note: See photo #2-A These are in place to overcome the spring tension or lock the stand in place and allow you to pivot the lower stand down partially to make installation easier. Pivot the upper stand about half way from the retracted to the extended (down) position. Note: This will require some force. If the stand will not stay in the position you can further tighten the two 9/16″ pivot nuts. Remove the bolts from the four band clamps. Wrap the (2) small clamps around the small upper frame tube and start the bolts so that the bolt will be at the bottom of the tube and the wrench head facing towards the rear of the motorcycle. Note: See photo #2. Center the stand on the frame from side to side so as to gain even clearance between the feet on the centerstand and the rear tire when the stand is in the retracted position. Holding the larger cradle up against the frame, tighten the (2) small clamps enough to hold the centerstand in place. Install one of the large clamps as shown in photo #3-A. Install the 2nd large clamp as shown in photo #2-C. Again retract the stand and check that the feet have even amounts of space from the side of the rear tire. Tighten the flour clamps securely 5-7 ft. lbs. Next remove the (2) 9/16″ pivot nuts and the white plastic washers as shown in photo #2-A. Re-install and tighten the 9/16″ pivot nuts securely 8-12 ft lbs. With the stand in the retracted position-adjust the stop bolt and lock nut, see photo #3-B, so that the stand is parallel with the ground and does not come in contact with any parts of the motorcycle. Using your new centerstand . To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail or grab under the bottom of the seat. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now put all of your weight onto the centerstand pedal (stand on it). Pull up and back on the grab rail or seat using a rocking motion to rock the motorcycle up onto the stand. Remember it is a matter of using your body weight and leverage not lifting!

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

Motorcycle stand Wheel chock set up and operating instructions

0

Filed Under (Tips and Review) by admin on 22-11-2010

download
1. can be adjusted to fit the wheel length. The Motorcycle Stand will fit most standard motorcycles currently on the market. However, some models with especially wide tires or custom low-profile front fenders will not fit. Mount the Support Arm (4) to the front of the Base using 2 Bolts (12), Washers 2. (5), and Nuts (6). Insert Pin (9) through the mounting holes and Cradle Stop (3); secure with Wash- 3. er (10) and R Pin (11). Insert Pin (9) through the mounting holes and Wheel Adapter (2); secure with 4. Washer (10) and R Pin (11). Securely tighten all hardware before use. 5. the Motorcycle stand must be mounted securely before use. 6. Page 5 SKU 97841 For technical questions, please call 1-800-444-3353. Mounting in concrete Choose a location to install the Motorcycle Stand that is flat, level, and capable of 1. bearing the combined weight of the Motorcycle Stand and the motorcycle being secured. The location should not obstruct walkways and provide enough room to retrieve the motorcycle after it is mounted. The surface of the location should be one suitable for the mounting of heavy equipment. Use the mounting holes in the Base (1) of the Stand as a template. Arrange the 2. Base in the chosen location and mark where the holes are to be drilled. You will need concrete anchors (not included) to secure the Base to the concrete 3. floor. Using the correct size concrete drill bit (not included), drill the mounting holes to secure the Base. Attach the concrete anchors to the floor. Secure the Base to the floor using con- 4. crete anchors.

Incoming search terms:

2008 CBR1000RR replace the clutch inner

0

Filed Under (Honda) by admin on 06-11-2011

download
Clamping Centerstand to Frame. Notice the centerstand is shipped with (2) white plastic washers. Note: See photo #2-A These are in place to overcome the spring tension or lock the stand in place and allow you to pivot the lower stand down partially to make installation easier. Pivot the upper stand about half way from the retracted to the extended (down) position. Note: This will require some force. If the stand will not stay in the position you can further tighten the two 9/16” pivot nuts. Remove the bolts from the four band clamps. Wrap the (2) small clamps around the small upper frame tube and start the bolts so that the bolt will be at the bottom of the tube and the wrench head facing towards the rear of the motorcycle. Note: See photo #2. Center the stand on the frame from side to side so as to gain even clearance between the feet on the centerstand and the rear tire when the stand is in the retracted position. Holding the larger cradle up against the frame, tighten the (2) small clamps enough to hold the centerstand in place. Install one of the large clamps as shown in photo #3-A. Install the 2 nd large clamp as shown in photo #2-C. Again retract the stand and check that the feet have even amounts of space from the side of the rear tire. Tighten the flour clamps securely 5-7 ft. lbs. Next remove the (2) 9/16” pivot nuts and the white plastic washers as shown in photo #2-A. Re-install and tighten the 9/16” pivot nuts securely 8-12 ft lbs. With the stand in the retracted position-adjust the stop bolt and lock nut, see photo #3-B, so that the stand is parallel with the ground and does not come incontact with any parts of the motorcycle

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

HONDA GL1500 Headlamp Adjustments Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
Headlamp Adjusting Procedure Tools needed • Long, slender #1 Phillips screwdriver (for adjusters behind the rubber plugs) • #2 Phillips screwdriver (for the other adjuster screw) • 12-inch square of cardboard • Flat wall or garage door • Paper, tape, marker NOTE: All adjustments are very fine. You have to turn the screws A LOT to see changes in adjustment. This procedure is best done after dark, because you will need to do some test rides. Preparation 1. Set the bike on its center stand, 10 feet away from an unobstructed wall or garage door, and square to the wall or door. 2. Remove the front fairing cover and lower vent grille to gain access to the headlamp adjusters. 3. Idle the engine or connect a battery charger to the battery, to prevent battery drain. Headlamp assembly viewed from the front, showing positions of mirrors and adjusters (pretend the lens has been removed) . Low Beam Vertical Alignment 1. With the lights on low beam, cover the right half of the lamp assembly with the cardboard square, so only the left bulb is shining on the wall. 2. Using a marker, mark the top of the left low beam on the wall (use paper taped to the wall if you don’t want to mark the wall itself) . 3. Move the cardboard so it blocks the left bulb, so only the right bulb is shining on the wall. 4. The top of the right low beam should be even with the mark you made for the left low beam. If it’s not, adjust by turning the screw behind the rubber plug at the top of the lamp assembly, using a long, slender #1 Phillips screwdriver. 5. Move the cardboard back and forth between the bulbs to verify that the low beams are at the same height. On high beam, the two hotspots should line up vertically. High Beam Vertical Adjustment 1. With the lights on high beam, note the position of the beams’ hot spots on the wall in relation to the mark you made in step 5 above. 2. Most owners complain about their low beams being too low on the roadway. To correct this, lower the high beams by turning the screw behind the rubber plug at the bottom of the headlamp assembly, using a long, slender #1 Phillips screwdriver. You can watch the high beam hot spot being lowered on the wall in relation to the mark you made. 3. Take a test ride. Get out on a dark street, and adjust the high beams using the dash knob until you like what you can see. Then switch to low beam and see how that looks. 4. Repeat these steps until you get the low beam pattern you want. Left/Right Adjustment 1. Back to the wall. Set the bike on its center stand at a distance of 25 feet from the wall and square to the wall. Center the front wheel. 2. Shine the high beams on the wall. 3. Step to the back of the bike, and level your eye with the center of the passenger backrest. Use the center of the backrest and the center of the windshield like a gunsight. The center of the hotspot of the high beam should hit the wall in this line. 4. Adjust by turning the uncovered screw at the bottom of the headlamp assembly, using a #2 Phillips screwdriver.

Incoming search terms:

HARLEY DAVIDSON FL SOFTAIL FOWARD CONTROL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
INSTALLATION Shifter Side, Left Block or jack vehicle under frame in a way that the vehicle will not fall over. Failure to properly block and/or raise the vehicle could result in death or serious injury. (00462c) 1. Block the motorcycle under the frame so that it is upright and level, with the weight off of the jiffy stand. 2. Remove footpeg. 3. Remove jiffy stand, shifter linkage and bracket per applicable Service Manual instructions, retaining hardware. 4. See Figure 5. Obtain the new left side shifter bracket (2), and three TORX® screws (3) from the kit. 5. Place washers previously removed on the screws. Apply LOCTITE® 243 (Blue) to the threads, and install the new bracket assembly to the motorcycle frame. Tighten the screws to 40 ft-lbs (54.2 Nm) . 6. See Figure 5. Install footpeg with spring washer (8), clevis pin (10) and retaining ring (9). If leg stop is incorrectly installed, excessive wear can allow vehicle to fall when rested on jiffy stand, which could result in death or serious injury. (00479b) 7. Install jiffy stand and attach the spring. When properly installed, the hook on the spring side connected to the bracket will face upward. 8. Verify that rubber bumper is in place on prong of jiffy stand. Without the bumper, the stand will make hard contact with the primary drive cover when retracted, which may result in damage to the cover. 9. Extend and retract the jiffy stand leg several times to verify proper operation. The stand should swing freely to the fully extended and fully retracted positions. 10. Refer to applicable Service Manual and re-attach the shifter linkage

Incoming search terms: