how to fix motorcycles mirror from sliding

You search Auto repair manual PDF how to fix motorcycles mirror from sliding, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to fix motorcycles mirror from sliding Direct Download speed 5282 Kb/s

  how to fix motorcycles mirror from sliding Full Version speed 6162 Kb/s



BMW R1100RT, BMW R1150RT Signal Mirror Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
1. These instructions start with the right side mirror. Grab the mirror housing as shown and slowly push down to disengage housing from motorcycle. 2. Once you have the mirror housing removed partially, twist and remove the light bulb from mirror housing. Remove mirror housing and set it on a cloth covered surface. 3. Remove the factory mirror by inserting a slotted screwdriver against each mirror mount snaps. Slowly twist and pry each snap until it releases from motor actuator. Repeat process until factory mirror disengages. NOTE: Insert the slotted screwdriver as close to each of the snaps as possible before prying out the OE mirror. Not doing so may cause the crossbar on the motor actuator to break. Connect the two mating connectors from the adapter Signal® mirror wire harness and the new Signal® mirror wire harness. Cut a slot in the foam disc to accommodate the anti-vibration prongs on the motor adapter. Place the foam disc onto the center of the Signal® mirror motor interface. Connect the Signal® mirror mating connector to the Signal® mirror wire harness. 5. Remove Cap Sheet from two-sided adhesive disc on back of Signal ® mirror. Align the anti-rotation prongs found on the top and bottom or left and right with the corresponding slots on the motor mount. Use the palm of your hand, push down on the Signal® mirror and the mirror housing until the Signal® mirror motor mount is fully engaged. Note: Push firmly on all sides of the Signal® mirror to ensure proper engagement and travel. Not doing so could result in mirror falling off. 6. Locate the light bulb and carefully disconnect the original light blue with black stripe wire [hot wire]. Connect the red wire from the Signal® mirror wire harness to the spade terminal on the light bulb. Connect the original light blue with black stripe wire to the other spade terminal located on the red wire of the Signal® mirror wire harness. Repeat the process for the original brown wire and the black wire from the Signal® mirror wire harness [ground wires]. Insert the light bulb back into the mirror housing. 7. Align the 3-pins with their corresponding snap holes and snap the mirror housing into place. 8. Insert key into the ignition and turn to the “ON” position. Activate the right hand turn indicator to verify that the new Signal® mirror is working correctly. Replace any other accessories necess

Incoming search terms:

HARLEY DAVIDSON LIGHTED MIRRORS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
REMOVAL Prepare for Service Touring Models: Remove left side saddlebag, left side cover, and maxi-fuse. Refer to SADDLEBAG and MAXI-FUSE in Service Manual. Softail and Dyna Models: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat according to the instructions in the Service Manual. 2. Disconnect battery cables, negative (-) cable first. 3. Remove fuel tank according to the instructions in the Service Manual. Sportster Models: Remove left side cover and maxi-fuse. Refer to MAXI-FUSE in Service Manual. V-Rod Models: Remove right side cover and maxi-fuse. Refer to MAXI-FUSE in Service Manual. Remove Existing Mirrors Touring and Softail (Except FXSTD, FLSTF) Models Left side: See Figure 1. Remove acorn nut (1), star washer (2), and existing mirror (3) from clutch hand control assembly. Discard star washer and mirror but save acorn nut. Right side: See Figure 2. Remove acorn nut (1), star washer (2), and existing mirror (3) from front brake hand control assembly. Discard star washer and mirror but save acorn nut. 2 1 3 is03431 1. Acorn nut 2. Star washer 3. Mirror, left Figure 1. Remove L.H. Mirror (Except Sportster) 2 1 3 is03432 1. Acorn nut 2. Star washer 3. Mirror, right Figure 2. Remove R.H. Mirror (Touring, Softail – Except FXSTD, FLSTF) Dyna, FXSTD, FLSTF, and VRSC Models 1. Left side: See Figure 1. Remove acorn nut (1), star washer (2), and existing mirror (3) from clutch hand control assembly. Discard star washer and mirror but save acorn nut. 2. Right side: See Figure 3. Loosen ball stud clamp (1) to remove directional lamp assembly (2). Remove retainer (3), star washer (4), and existing mirror (5) from front brake hand control assembly. Discard star washer and mirror but save remaining parts. 2 5 3 1 4 is03428 1. Ball stud clamp 2. Directional lamp assembly 3. Retainer 4. Star washer 5. Mirror, right Figure 3. Remove R.H. Mirror (Dyna, FXSTD, FLSTF, VRSC) Sportster Models Left side: See Figure 4. Remove locknut (1), washer (2), and existing mirror (3) from clutch hand control assembly. Discard washer and mirror but save locknut. Right side: See Figure 4. Remove locknut (1), washer (2), and existing mirror (4) from front brake hand control assembly. Discard washer and mirror but save locknut. 3 2 1 2 1 4 is03414 1. Locknut (2) 2. Washer (2) 3. Mirror, left 4. Mirror, right Figure 4. Remove Mirrors (Sportster) INSTALLATION Install Lighted Mirrors Touring and Softail (Except FXSTD, FLSTF, FXSTS, FLSTS) Models 1. Left side: See Figure 5. Install mirror stem (1) through clutch hand control assembly.

Incoming search terms:

HARLEY DAVIDSON ILLUMINATED CHROME COVER KIT FOR FAIRING MOUNT MIRRORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION Preparation Models with main fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. Models with main circuit breaker: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. Installation NOTE Cover the work surface with an H-D Service Cover or clean shop towels to prevent scratching the finish of the outer fairing. 1. Remove the outer fairing per the instructions in the service manual. Lay the fairing face down on a sturdy work sur- face. 2. See Figure 2. Remove the mirrors (2), flange nuts (3) and plastic backing plates (4) securing the mirrors to each side of the inner fairing (1), and retain all items 3. Measure one inch (25 mm) straight down (5) from the large mirror stud hole in the inner fairing, and make a mark. 4. Drill a 1/4 inch (6 mm) diameter hole (6) through the inner fairing at the mark. 5. See Figure 1. Obtain a chrome wire collar (3) from the kit, and press it into the new hole from the outside of the inner fairing. Gently tap into place with a soft-faced hammer. 6. Repeat Steps 3 through 5 on the opposite side of the inner fairing. NOTE Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the mirror cover to the mirror. 7. Clean the back surface of the mirrors with the alcohol pad (7) provided. Allow to dry thoroughly. 8. Obtain the primer tube (8) from the kit, and follow the instructions on the tube to activate the primer. When the primer is activated apply the primer to the back surface of one mirror. 3 6 2 1 4 5 is06091 1. Inner fairing 2. Fairing mount mirror 3. Flange nut (2) 4. Plastic backing plate (2) 5. Measure one inch (25 mm) down 6. Drill 1/4 inch (6 mm) hole (2) Figure 2. Fairing Drill for Illuminated Mirror NOTE The Illuminated Chrome Mirror Covers are side-specific. The covers install with the wire harness exiting from the bottom. 9. Obtain the correct mirror cover from the kit. Rub the liners on the three pads on the back surface of the mirror cover to activate the adhesive, then remove the liners. 10. Place the mirror cover over the back surface of the mirror and press into place for a minimum of 60 seconds. 11. Repeat Steps 8 through 10 for the remaining mirror and cover. NOTE The plastic backing plates (removed earlier) are identified with a letter “L” (left) or “R” (right) stamped on the post. The mirrors are marked with a letter “L” or “R” stamped on the swivel block. Use the correct backing plate for each mirror by matching the letters. 12. Position the mirror on the outer face of the inner fairing, with the rounded side of the mirror outboard and the Bar & Shield logo upright. a. Insert the mirror cover wiring harness through the chrome wire collar installed in Step 5. b. Insert the mirror post through the original mirror mounting hole. c. Place the correct plastic backing plate against the inner face of the inner fairing, engaging the two holes in the backing plate with the threaded stud and index pin on the mirror swivel block. d. Install the flange nut on the threaded stud and tighten to 30-40 in-lbs (3.4-4.5 Nm) . e. Repeat for the remaining mirror on the other side of the fairing

1988-2000 Honda Goldwing GL 1500 Signal Mirror Installation Instructions

0

Filed Under (Honda) by admin on 29-01-2011

download
Start on either the left or right side mirror. These instructions start with the right side mirror. Pull back the rubber boot covering the mirror mount. 1 2 3 Remove the accessory compartment cover. Remove the four screws on all sides of the accessory compartment. Remove the accessory compartment from the motorcycle fairing and set it aside. 4 The motorcycle’s electrical wiring for turn indicators is located forward of the accessory compartment cavity and behind the front amber turn indicator light. Disconnect the wire connected to the turn indicator light. 5 There are three screws holding the mirror housing to the mirror mount. Remove the three screws. Set the mirror housing aside.
Mirror Replacement – 2 – Remove the three screws holding the hinge to the mirror housing. Remove the hinge and remove the rubber boot surrounding the mirror housing. 1 Match the base of the hinge up to the new Signal® mirror housing. Mark the place on the hinge where the Signal® mirror wire will go through. Drill a ¼” hole in the hinge. 2 Position the rubber boot over the Signal® mirror housing. 3 Guide the Signal® mirror wire harness through the drilled hole in the hinge. Mount the hinge on the Signal® mirror housing using the original three screws.

Incoming search terms:

HARLEY DAVIDSON FLHX MIRROR COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
INSTALLATION 1. Remove the outer fairing using service manual instructions. 2. See Figure 1. Remove the mirrors (1) and retain the flange nuts (2) and plastic backing plates (3) securing the mirrors to the inner fairing. Do not heat or bake plastic parts after painting. Applying heat can damage plastic parts. (00615b) NOTE The adhesive will not bond correctly if it is applied at temperatures less than 50° F (10° C). 3. For primed/painted mirror kits: See Figure 2. Install mounting tape to the mirror covers as follows: a. Clean the tape mounting surface of the mirror cover (1) with alcohol pads provided. Allow to dry com- pletely. b. Get the primer tube and follow the instructions on the tube to activate the primer. When the primer is activated apply the primer to the tape mounting surface of the mirror cover. c. Rub the adhesive backing of the mounting tape (2 or 3) to activate the adhesive then remove the backing. d. Install mounting tape to the mirror cover in the locations shown. Press tape and hold in place for 60 seconds. e. Repeat steps c and d and attach each piece of mounting tape to the mirror cover as shown, then repeat step 3 for the opposite mirror cover. 4. Clean the backside of the mirrors with the alcohol pads provided. Allow to dry completely. 5. Get the primer tube and follow the instructions on the tube to activate the primer. When the primer is activated apply the primer to the back face of the mirror. 6. Rub the adhesive backing on the backside of the mirror cover to activate the adhesive then remove the backing. 7. Place the mirror cover over the backside of the mirror and press into place for a minimum of 60 seconds. 8. Repeat steps 4 through 6 for the opposite mirror. 9. With the mirror post on the outboard side, place the plastic backing plate against the inner fairing engaging two holes in the washer with the threaded stud and index pin. The letters “L” or “R” are stamped on the backing plate posts to differentiate between the left and right side. Repeat for opposite mirror. 10. Install the flange nut on the threaded stud and tighten to 30-40 in-lbs (3.4-4.5 Nm) . 11. Install the outer fairing using the service manual instruc- tions

1999-2002 Indian Motorcycle Mirror Housing Removal and Replacement

0

Filed Under (Indian) by admin on 31-10-2010

download
1. Remove seat. 2. Disconnect battery. 3. Remove handlebar cover on top-center of handlebar. 4. Remove left-side clutch-bracket assembly. This exposes an access hole on the underside of the handlebar. 5. Pass the end of the Signal® mirror wires through one of the small holes located on the underside of the clutch-bracket assembly housing. 6. Take piano wire/fish tape and insert at the access hole located on the underside of the handlebar to the center of the handlebar (center handlebar cover removed). 7. Fasten the end of the Signal® mirror wires to the piano wire/fish tape and pull through the handlebars to the center opening. 8. Pull excess wire through the handlebars leaving approximately 2″ of extra wire at the mirror side. 9. Re-assemble clutch-bracket assembly allowing the Signal® mirror wire to wrap around the outside edge of the cover assembly into the underside access hole. Secure Signal® mirror with enclosed 1.5″ long 5/ 16 ” – 24 Allen head bolt. 10. Loosen throttle assembly side and slide back to expose access hole. DO NOT REMOVE THROTTLE ASSEMBLY. Proceed to pass the Signal® mirror wire through the handlebar at the opposite side and re-assemble the throttle assembly. 11. Run both sets of wires under the fuel tank along the topside of the frame to the battery compartment. 12. Connect both black wires to the enclosed ring connector for connection to the battery ground terminal. 13. Locate the male/female electrical connector that is located behind the battery. This wiring assembly is for your tail lamp assembly for braking and turning (see photo). 14. Make sure the harnesses are routed securely to the wire connectors and enough slack is left for splicing or soldering. Cut the heat shrink into (4) equal pieces (approx. 2″ each). 15. Slide the heat shrink over the passenger side Signal® mirror wire. Solder the Right Signal® mirror wire to the Brown wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 16. Repeat sliding the heat shrink over the driver side Signal® mirror wire. Solder the Left Signal® mirror wire to the Purple wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 17. Connect ground and positive battery connections. 18. Re-install seat.

Incoming search terms:

1999-2005 BMW K1200LT Motorcycle Signal Mirror Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Start on either the left or right side mirror. These instructions start with the right side mirror. Remove the factory mirror by inserting the pry bar as shown. Slowly twist the pry bar to disengage the mirror. NOTE: Insert the pry bar as close to the mirror mount as possible before prying out the OE mirror. Not doing so may cause the crossbar on the motor actuator to break. 2. Grab the mirror housing as shown and slowly push down to disengage housing from motorcycle. 3. Once you have the mirror housing removed, route the Signal® mirror wire harness through the hole in the housing. Note: Leave about 6″ of slack, on the wire, for adjustment later on. 4. Use a screwdriver and remove the screw from the front turn indicator lens. 5. Disengage the lens and remove the light bulb as shown. 6. Route the Signal® mirror wire harness through the top opening in (A) and out the bottom opening in (B).

Harley Davidson Motorcycle 1982-2009 Standard Signal Mirror Kit INSTALLATION

0

Filed Under (Harley Davidson) by admin on 23-02-2012

download
Remove the 5/ 16 ” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. NOTE: Use of oil is suggested if bolts do not thread easily into stem base. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Start on either the left or right side mirror. These instructions start with the right side mirror. Remove the factory mirror. NOTE: For motorcycles with OEM forward facing indicators, please use the instructions on the last page in lieu of step 2.

HARLEY DAVIDSON SPLIT VISION MIRROR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
These kits are designed to fit all 1982 and later Harley- Davidson motorcycles. Kit Contents See Figure 1 and Table 1. INSTALLATION 1. Remove and discard the existing mirror. Discard any lockwashers and acorn nuts used to mount the original mirror. 2. For motorcycles with turn signals mounted to the underside of the hand lever housings except 2004 and later XL models: See Figure 1. Secure the left side mirror using only the flat washer (3) and the acorn nut (5) from the kit. 3. Secure the right side mirror with the flat washer (3) and acorn nut (5) from the kit and the turn signal retainer only. Do not use washer (4) on either side. For 2004 and later XL models use only the lockwasher (4), and acorn nut (5) on each side. 4. For motorcycles with turn signals mounted away from the hand lever housings: Insert the mirror studs into the holes in the hand lever housings, and secure the mirrors with the flat washers (3), lockwashers (4) and acorn nuts (5) from the kit. 5. Adjust the mirrors for proper field of vision and tighten the acorn nut to 12 ft-lbs (16 Nm). Check mirror adjustment and reposition if necessary

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

Incoming search terms: