how to hook up tach for 74 shovelhead

You search Auto repair manual PDF how to hook up tach for 74 shovelhead, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to hook up tach for 74 shovelhead Direct Download speed 5282 Kb/s

  how to hook up tach for 74 shovelhead Full Version speed 6162 Kb/s



Baron Tachometer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Some models like Harley-Davidson, Kawasaki Vulcan FI models, Suzuki FI models, Honda VTX 1800 and others may require the included Tach Adapter. See separate instructions for installation of the adaptor. Wiring instructions for 7-Color LED Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire of tach to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire of tach to CHASSIS (Ground) • Red wire to of tach to POSITIVE terminal of coil (or other switched 12 volt source) • Red wire from control box to POSITIVE terminal of coil (or other switched 12 volt source) • Black wire from control box to CHASSIS (ground) • Control box plugs into tach with the 4-way connector • Button plugs into the control box. Button can be mounted on handlebar or any other convenient place Wiring instructions for White- or Black-Face Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire to CHASSIS (Ground) • Red wire to POSITIVE terminal of coil (or other switched 12 volt source) • Blue wire to POSITIVE terminal of coil (or other switched 12 volt source) General mounting instructions (1) Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off- center, you can rotate tach face back to vertical (or any position you desire) by first loosening tach unit’s set screw (found either in handlebar area of housing or underside of housing, depending on tach style), then unscrewing tach housing’s bezel, rotating tach, re-installing bezel and retightening set screw. Secure handlebar clamp by first tightening the rear, flat side of clamp all the way down, then tighten tapered front side of clamp until tach does not rotate. There should be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened. (2) Route tach’s wire harness lead to coil as necessary for simplest and cleanest installation. Feed tach harness alongside bike’s wiring harness (passing behind any plastic frame covers), then downward toward coil. (3) Make your wire connections as recommended above. Use the spade and piggyback connectors

Incoming search terms:

Kawasaki Mule Duster Adhesive Hook Strip Installation Instructions

0

Filed Under (Kawasaki) by admin on 30-04-2012

download
Use the loop on the Duster as a guide to locate the Hook Strip on the front of the bed. Clean the area and install the Adhesive Hook Strip as in Step 1. Install Adhesive Hook Strip to Front of Bed Cut the Adhesive Hook Strip into six (6) pieces to match the loop sewn to the Duster. Use the loop on the Duster as a guide to locate the Hook Strip on the sides of the bed and the tailgate. Clean the areas with a 50% Water/Alcohol Solution. Peel the backing off the hook a little at a time and press it fi rmly into place. Install Adhesive Hook Strip Allow 72 hours for the adhesive to set. Avoid unnecessary fastening and unfastening of the Duster during this period. Open Bed Open the bed of the vehicle. Tailgate Adhesive Hook Strip Allow 72 hours for the adhesive to set. Avoid unnecessary fastening and unfastening of the Duster during this period. Secure Duster to Front of Bed Fasten the loop sewn to the front of the Duster to the Adhesive Hook Strip on the front of the bed

Incoming search terms:

YAMAHA 1996-2003 Road Star BILLET TACH MOUNT KIT INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 12-01-2012

download
Remove and retain the (4) chrome caps from the handlebar clamps. Remove and retain the (4) stock allen head bolts. This hardware will be re-used with the new Billet Tach Mount Kit. Carefully remove the stock handlebar clamps while supporting the handlebars. INSTALLATION: 2. Slide the Electronic Tachometer (#6) into the Billet Tach Mount (#2) and secure with the 10-24 X 1/4″ Socket Set Screw (#10) supplied. Carefully pull the tachometer wire harness through the larger hole in the Billet Tach Cup (#3) and secure the Billet Tach Cup with the 10-24 X 1/8″ Socket Set Screw supplied. (The additional holes in the tach cup are for air circulation). Attach the Billet Tach Mount to the Billet Handlebar Clamp (#1) with the two 10-24 X 1-3/4″ Socket Head Screws (#4) supplied. Install the Billet Tach Mount assembly with the four stock allen head bolts and chrome caps removed in step 1 above. Adjust handlebars to desired height and torque bolts to factory specs. WIRING INSTRUCTIONS: 3. Refer to FIG. #1 . Remove Seat. Disconnect negative cable from battery. Remove fuel tank retaining bolts. Raise fuel tank about 3″-4″ to expose the Left Side Ignition Coil. It is not necessary to completely remove the gas tank on the Road Star. (V-Star 1100 applications use the right front coil and require fuel tank removal.) TIP: Long needle nose pliers are useful in removing and re-installing the coil wires. If desired, tach wire loom may be shortened as necessary. Using an appropriate crimping tool, connect the Tachometer wires in the following manner: Cut Shrink Tubing (#9) into two 1″ pieces

Incoming search terms:

1980-2003 HARLEY DAVIDSON BARON TACHOMETER installation manual

0

Filed Under (Harley Davidson) by admin on 12-03-2012

download
1. Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off-center, you can rotate tach face back to vertical (or any position you desire) by first loosening tach unit’s set screw (found either in handlebar area of housing or underside of housing, depending on tach style), then unscrewing tach housing’s bezel, rotating the tach internals, re-installing the bezel and retightening the set screw. 2. Secure handlebar clamp by first tightening the rear, flat side of clamp all the way down, and then tighten the tapered front side of clamp until tach does not rotate. There should be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened. 3. Route tach’s wire harness lead under dash for simplest and cleanest installation. 4. Make your wire connections as follows: a. Locate the pink wire under the speedo (sometimes has a plastic bullet end on it). Cut the plastic off and splice the pink wire with the green wire from the tachometer. b. Find the orange wire and attach the tach power wires to it (usually blue & red from tach (incandescent) or red & yellow for single color LED tachs. On 7-color LED models it is red from tach and red from LED controller box) . c. Locate a suitable ground (usually a bare frame bolt) and attach the black wires from the tachometer and the LED controller box (if equipped).

Incoming search terms:

HARLEY DAVIDSON MINI-TACH WITH SHIFT LIGHT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION Preparation For EFI models: To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) Follow the instructions found in the Service Manual to purge the fuel supply of high pressure gasoline and remove the fuel supply line. For ALL models, WITH Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the Maxi-Fuse. For ALL models, WITHOUT Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. -J04106 Gasoline can drain fr om the carb uretor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) 2. For carbureted models: Turn the fuel supply valve to OFF. Remove the fuel line from the valve. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 3. For ALL models: Follow the instructions in the Service Manual to remove the instrument console from the fuel tank. 4. See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 5. For all models EXCEPT FLHR or 1986 and later FL Softail models with Chrome Headlight Nacelle Kit (Part Number 67907-96): Follow the instructions in the Service Manual to remove the headlamp housing. For FLHR models, or Softail models WITH the Nacelle Kit: Follow the instructions in the Service Manual and the mini-tach bracket kit (purchased separately) to remove the handlebar shroud. Mini-Tach Bracket Installation 6. For all models except FLHR: Install the mini-tach bracket components per the instructions in that kit. For FLHR models: Follow the instructions in the Service Manual and the mini-tach bracket kit to install the handlebar shroud and bracket components. 7. See Figure 7. Select the rubber isolation gasket (1) from this kit.

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK WALL ORGANIZER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
This kit fits 1997 and later models equipped with King Tour- Paks INSTALLATION NOTE Maximum Wall Organizer weight capacity is 3 pounds (1.4 Kg) evenly distributed. Do not exceed tour-pak weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00401b) Tour-Paks With Molded Liner 1. Remove the two nuts that hold the pouch and liner in the Tour-Pak. Remove pouch and liner and carefully wash the inside of the Tour-Pak with warm, soapy water. Rinse and dry thoroughly. 2. Use the alcohol prep pad in the kit to thoroughly clean the interior surface of the Tour-Pak sides where fastener strips will be attached. Make sure any residue is removed, then allow Tour-Pak to dry completely. Make sure the surface is free of condensed moisture. NOTES The hook and loop fastener strips and organizer must be installed below the edge of Tour-Pak base to avoid interference with top gasket and lock. The ideal temperature range for applying the fastener strip is 70-100° F (21-38° C). Minimum application temperature is 50° F (10° C). If you attempt to apply the tape below these temperatures, the adhesive will become too firm to adhere readily. 3. See Figure 1 and Figure 2. Remove the hook and loop fastener strips from the hinged hook and loop strips. Remove the paper backing and firmly press the fastener strips into the locations (1) shown in Figure 2. The fastener strips should be located approximately 1/8 in. (3 mm) below the edge of the Tour-Pak base. 4. See Figure 1. Bend the hinged hook and loop strips (3) into shape as shown. Attach the hinged strips onto the fastener strips (2) installed in Step 3. NOTE The Tour-pak Wall Organizer installs in place of the pouch removed in Step 1, therefore the pouch will not be re-installed. 5. Reinstall the liner removed in Step 1. The hinged strips (3) will go over the top of the liner (4) as shown in Figure 1. 6. See Figure 1. Attach the organizer (5) to the hinged strips (3). Adjust the organizer’s lock cut out so that it is centered around the lock, and press the hook side of the hook and loop strips on the bottom of the organizer into place on the liner. The hook side will attach to the liner. NOTE 2006 and later Tour-Paks equipped with Passenger Backrest will have two acorn nuts at the front of the base. Remove and discard the 8 in. (200 mm) long hook and loop hinged fastener strip from the center panel. In one of the organizer pockets there will be 4 in. (100 mm) and 1-1/2 in. (38 mm) hook and loop hinged fastener strips. Install the hinged strips on the organizer center panel as shown in Figure 3. 7. Check to make sure the Tour-Pak lid closes over the organizer and the lock works without interference. Adjust as necessary. 8. Allow tape to cure (“wet-out”) for a minimum of 48 hours at 70° F (21° C) (allow extra time if temperature is below 70°). Do not place items in the Wall Organizer while adhesive is curing

1999-2003 Harley Davidson TC88 Micro Tach TM Tachometer Installation Manual

0

Filed Under (Harley Davidson) by admin on 10-03-2012

download
Installation of the Speedway Instruments microTach+TM tachometer requires some basic mechanical skills, including removing decorative covers, cutting protective tubing around wires, and using suitcase splice connectors to splice existing wiring harness. These actions may void your warranty, and if done incorrectly may cause damage to your motorcycle. Only you know your capabilities, if you do not feel capable of making modification please have a qualified motorcycle technician install it. Speedway Instruments, LLC is not responsible for damage to your motorcycle due to improper installation. The microTach+ TM tachometer designed for 1999-2003 TC88 Harley Davidson motorcycles is designed to operate when connected to a dedicated Tachometer signal from the Electronic Ignition Controller. It is not intended to run off signals going to the ignition coil unless utilizing a Speedway Instruments Tach Adapter. WARNING: Damage may occur to the microTach+ TM tachometer or your motorcycle if micro Tach+ TM tachometer is connected directly to coil signals, you must use a Speedway Instruments tach Adapter (sold seperately) ! ! 1. Turn ignition off and disconnect Battery. 2. Determine a mounting position. Each motorcycle is unique and the microTach+TM tachometer is small enough to be placed in many different locations to provide an attractive appearance and vital engine status. Possible locations are: a. Front Brake Reservoir

BULLET & MINI-BULLET TACHOMETERS INSTALLATION MANUALS

0

Filed Under (Tips and Review) by admin on 22-02-2012

download
UNDER THE HANDLEBAR MOUNTING A: Can the Tach be mounted inverted under the handlebars? A: Yes, if you have enough room to mount under the handlebars for the tach to mount and still be able to turn from lock to lock without hitting the tank or dash. See note in next paragraph for details on how to rotate the face of the Tach for appropriate positioning. BE AWARE: Chances of water intrusion are increased in this position! FACE ROTATION Q: How do I rotate the face of the Tach? A: With the Tach housing removed from the handlebar, unscrew the bezel (counterclockwise) and remove it from the housing, using a 5/32 Allen wrench loosen the the set-screw located inside the clamp area or at the rear of the clamp area. Rotate the face of the Tach to your preferred position, tighten the set screw and replace the bezel. COIL IDENTIFICATION Q: How can I tell positive from negative on my coil? A: Most motorcycles will have two wires going to each of the coils, and each coil will share one common-color wire and have one unique color wire. The common-color is the positive and the unique color is the negative. For example, a Yamaha set-up has a red/black on both coils – that is positive. The other coil wire would be orange or gray – that is the negative side. Hondas set-up is blue/yellow and yellow/blue for the negative, and black/white for the positive. Suzuki has orange/white on both coils as positive and has white or black/yellow as the negative side. COIL SELECION Q: My bike has two (or four) coils – Which one/ones do I use? A: Most multi-cylinder bikes have one coil per cylinder. You only need to connect to one of the coils – choose the one most convenient for wire routing. (Single-fire motorcycles require the Tach adapter we include with each assemble

HARLEY DAVIDSON SADDLEBAG LID COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION NOTE To avoid failure, the fastening tab adhesive must be allowed to cure for 24 hours before installing these Lid Covers. NOTE Lid Cover installation may be easier with the saddlebags removed from the motorcycle. 1. See Figure 1. Open the saddlebag lid. Remove the two T-20 TORX® screws (5) attaching the check strap (3) to the lid. 2 4 2 3 1 6 7 4 4 6 5 is02962 1. Saddlebag lid cover 2. Hook and loop fastener, 1.5 inch 3. Check strap 4. Hook and loop fastener, 4.0 inch 5. Torx screws (2) 6. Hook and loop fastener, 6.0 inch 7. Anchor tab (install first) Figure 1. Saddlebag Lid Cover Installation 2. Wash the entire saddlebag lid, inside and out, with warm, soapy water. Rinse and dry thoroughly. 3. Use the alcohol prep pad provided in the kit to further clean the inside of the lid in the areas where the hook and loop strips will be attached. NOTE The Saddlebag Lid Covers are side-specific. A Bar-and-Shield logo is stitched into the rear face of each cover. NOTE DO NOT fasten the Saddlebag Lid Cover tabs to the hook and loop strips until the adhesive has cured for 24 hours. 4. Place the correct Saddlebag Lid Cover (1) over the saddlebag lid in its proper position. Bring the cover tabs over the edge of the lid to serve as a guide in positioning the hook and loop strips on the inside of the lid. Remove the protective backing from one hook and loop strip at a time. Use the corresponding tab on the cover only as a positioning guide, then fold it back out of the

Harley-Davidson MINI-TACH GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2012

download
1. Refer to the Service Manual and follow the instructions given to remove the Maxi-Fuse. For ALL models, WITHOUT Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. -J03119 1 of Gasoline can drain fr om the carb uretor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) 2. For carbureted models: Turn the fuel supply valve to OFF. Remove the fuel line from the valve. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 3. For ALL models: Follow the instructions in the Service Manual to remove the instrument console from the fuel tank. 4. See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 5. For all models EXCEPT FLHR or 1986 and later FL Softail models with Chrome Headlight Nacelle Kit (Part Number 67907-96): Follow the instructions in the Service Manual to remove the headlamp housing. For FLHR models, or Softail models WITH the Nacelle Kit: Follow the instructions in the Service Manual and the mini-tach bracket kit (purchased separately) to remove the handlebar shroud.

Incoming search terms: