how to hotwire a kawasaki vulcan 1996

You search Auto repair manual PDF how to hotwire a kawasaki vulcan 1996, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to hotwire a kawasaki vulcan 1996 Direct Download speed 5282 Kb/s

  how to hotwire a kawasaki vulcan 1996 Full Version speed 6162 Kb/s



Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

CHANGING OIL IN THE KAWASAKI VULCAN VN 2000

0

Filed Under (Kawasaki) by admin on 16-12-2010

download
CHANGING OIL IN THE KAWASAKI VULCAN VN2000 ( based on a 2005 model) by tensm an1 Preparing the motorcycle: 1. To start, level the motorcycle – my preference is to put a spacer blocks under the kickstand on the left side of the motorcycle and under the frame on the right side of the bike just under the frame member. These blocks are made from scrap lumber. I find it is easier to set the right side block first as shown and tilt the motorcycle until the frame contacts the block, then, holding the handlebars, kick the left side block under the kickstand. 6″ NOTE: This dimension may not be correct for 2004 models as the 2005 models have a different kickstand – the 2004 model will likely be thicker. To be sure your blocks are the correct thickness the first time, lay a level across the luggage rack as shown. You may need to shim them slightly to hold the bike dead level. 2 7/8″”
Or, in the absence of a luggage rack, the seat will do: 2. Get the necessary tools ready: Oil filter wrench – I like the band type shown, but a metal strap type will work. 14 mm box wrench

KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 23-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove right side frame cover. 2. If motorcycle is oxygen sensor equipped, remove passenger seat. Remove two bolts securing operator seat and set seat aside. Locate and unplug oxygen sensor connector from wiring harness (Figure 1).(Note wire routing for reassembly). 3. Remove right side floorboard assembly held in place by two bolts (Figure 2). 4. Remove exhaust port flange nuts. 5. Remove flange bolts securing rear muffler to exhaust system mounting bracket. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). Page 1of 4 K400IN Rev. 1.1 KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM Part #18311 Tools required for installations 6mm Allen wrench 8mm 12mm 14mm sockets 3/8″ Ratchet & Extensions 19mm Wrench 9/16 Wrench Brake bleeder & fluid
7. Check condition of stock exhaust gaskets. Replace if damaged or worn. 8. Remove plastic hose clamp securing rear brake hose to swingarm.Save for re-use. 9. Remove brake hose banjo bolt from rear caliper. 10. Slide hose out of loops in swingarm. 11. Remove three bolts holding stock exhaust mounting bracket and slide bracket off end of brake hose. 12. Slide brake hose through loop on new bracket (stamped 357-P) and install to the original mounting bracket location, using three 8mm x 16mm Allen bolts (supplied) (Figure 3). 13. Check condition of sealing washers on banjo bolt and replace if damaged or worn. 14. Slide brake hose through loops on swingarm and reconnect brake hose to caliper. 15. Reinstall plastic clip onto swingarm. 16. Brake system must be bled or brake will not operate correctly.

Incoming search terms:

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

KAWASAKI VULCAN 900 SLASH CUT STAGGEREDS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Attach mounting bracket 440-P to frame using two stock fl ange head bolts used on stock upper bracket (Figures 1 and 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 3). 3. Lay front header, and rear header into their head heat shields and muffl er body heat shields. 4. Install #20 hose clamps (supplied) on heat shields and #36 (supplied) on muffl er body heat shields by feeding tail end of clamps into heat shield clips (fi gure 3). Take note of clamp screw head direction (Figure 4). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 5. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 6. Slide nut plates inside bracket that is welded to backside of muffl er bodies (Figure 5). While holding nut plates in place, attach muffl er bodies to mounting bracket 440-P using two 5/16″x 5/8″ fl ange head bolts (supplied). Leave them loose at this time. 7. Align muffl er bodies so they are level and parallel when viewing from the right side of the bike. Tighten cylinder port exhaust fl ange nuts on front and rear cylinders. 8. Tighten the fl ange bolts on both muffl ers. 9. Tighten all heat shield clamps. 10. Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. NOTE: For models with fl oorboards, two Spacer washers are supplied to space out the fl oorboard bracket enough to allow the fl oorboard to fold up without hitting the heat shield. 11. Be sure to tighten all hardware before starting your motorcycle. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up

Incoming search terms:

Kawasaki Vulcan 400/ 800 Preload Improvement Kit Installation Instructions

0

Filed Under (Kawasaki) by admin on 01-12-2010

download
1. Begin by removing both side compartment covers. The RH compartment cover requires the use of the ignition key for removal; the LH compartment cover is secured by a large Phillips screw. Once you’ve removed the LH cover, place the Phillips screw back into the hole in the frame (so you don’t misplace it) and set both covers aside. In many applications, you must remove the upper exhaust pipe (from the rear cylinder), and loosen the other pipe, to remove the inner parts of the RH side compartment cover (see below). Before attempting step #2 below, try step #3 first… depending on the brand of exhaust pipes you have, you may be able to avoid removal in step #2, if you are successful with step #3 first. Some brands of exhaust pipes provide access to the fasteners securing the RH side covers, eliminating the requirement to remove pipes for rear suspension access. 2. Remove the rear cylinder’s exhaust pipe. To do so, remove the two Allen nuts on the exhaust header, where it attaches to the engine, using an 8mm Allen wrench. Most often, this goes much more smoothly if you first spray the inside of the allen nut with a penetrating lubricant like WD-40. Remove the black acorn nut from the discharge end of the exhaust pipe (under the upper exhaust pipe, near the discharge end of the pipe) using a 12mm open-end wrench or socket. You’ll find a black metal spacer, through which the bolt goes, that is pressed through the rubber grommet. To avoid the potential of having it fall out unnoticed, remove it and place it aside with the nut. Remove the black bolt from the pipe just aft (to the rear) of where the pipe enlarges and above the pipe. This is actually a bracket that holds the two pipes together at a joint. Loosen the bolt using a 12mm socket, then slide it back onto the pipe you’re removing. Once you have the pipe off of the bike, the clamp will be loose. Be sure to keep it with the pipe, along with the rest of the removed parts. Loosen the pipe from the front cylinder BEFORE trying to remove the pipe from the rear cylinder. By loosening the header nuts on the pipe from the front cylinder, and removing the two black Allen bolts (6mm Allen wrench) under the forward pipe that attach it to the frame, you will be able to remove the rear pipe. There are more spacers in grommets where the 6mm Allen bolts secure the lower pipe to the frame (like those used in the rearmost connection o

Incoming search terms:

Kawasaki Vulcan 1600 Classic Exhaust Serrated Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Loosen both top and bottom muffler hose clamps as shown. (Fig.1&2) Figure 1 Figure 2 2. Remove 10mm bolt with 10mm nut on back side of bracket as shown. (Fig. 3&4) Figure 3 Figure 4 3. Loosen 6mm bolt on passenger foot peg bracket as shown. Once loose remove top muffler 10mm nut and 10mm bolt. Slide bolt out of rubber grommet. (Fig.5&6) Figure 5 Figure 4. Carefully remove top and bottom stock mufflers, by sliding both mufflers out by rear fender. (Fig. 7) Figure 7 5. Use Phillips screw driver and remove bolt as shown. Remove side cover carefully by pulling towards your body. (Fig.8&9) Figure 8 Figure 9 6. Remove rear head pipe by removing two stock socket cap nuts as shown. Once nuts are removed pull rear head pipe away from bike and set aside. (Fig.10) Figure 107. Remove stock front head pipe by removing two stock socket cap nuts as shown. Once nuts are removed pull front head pipe away from the bike and set aside. (Fig.11&12) Figure 11 Figure 12

KAWASAKI VULCAN 800 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two header flange nuts from the front and rear head pipes. 2. Remove the acorn nut located under the rear muffler. 3. Remove the two allen bolts located under the front muffler. 4. Remove the stock exhaust system from the motorcycle and set it aside. 5. Remove the two hex head bolts that attach the stock muffler mounting bracket to the frame of the motorcycle. Remove the muffler bracket and set it aside. 6. Remove the two rubber grommets and spacers from the stock muffler and the one grommet and spacer from the muffler mounting bracket. Set them aside with the the two mounting bolts, they will be reused during installation. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install the heat shield to the front head pipe using the three hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 3. Install the stock rubbber grommets and spacers into the three large holes on the V&H mounting bar (See figure 1). 4. Be sure the steel spacers are in place in the center of the grommets. Install the two allen bolts (from removal step #3) through the mounting bracket and into the frame. Leave them loose at this time. 5. Install the front head pipe with the heat shield attached, to the front cylinder using the stock nuts. Leave them loose at this time.

Kawasaki Vulcan 500 Receiver Hitch Installation Manual

0

Filed Under (Kawasaki) by admin on 06-05-2012

download
1) Place motorcycle on its side stand on a firm level surface. 2) Remove saddlebags if any. 3) Remove rear riders pegs. 4) Attach front of bracket A (left side) and bracket B (right side) between rear footpeg motorcycle bracket and rear footpeg. Use new bolt provided (Bolt assortment included to accommodate some accessories) 5) Attach bracket E (left side) and bracket F (right side) to two rear fender attachment bolts. Use new bolts provided. (Bolt assortment included to accommodate some accessories) 6) Attach bracket C (left side) and bracket D (right side) to brackets E and F and to second holes on rear of hitch. 7) Attach rear of brackets A and B to BOTTOM of hitch arms 8) Tighten all bolts. Receiver hitch diagram Leveling stand screw jack installation After hitch is installed, install leveling stand screw jacks to hold motorcycle in an upright and level position in order to install or remove InstaTrike. 1) Thread right side screw jack into leveling stand bracket on bracket B and adjust leveling jack bolt out until motorcycle will be level against it. 2) Push motorcycle over from left side until right screw jack is touching floor.

KAWASAKI VULCAN 800 STRAIGHT SHOT EXHAUST SYSTEM INSTALATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two header flange nuts from the front and rear head pipes. 2. Remove the acorn nut located under the rear muffler. 3. Remove the two allen bolts located under the front muffler. 4. Remove the stock exhaust system from the motorcycle and set it aside. 5. Remove the two hex head bolts that attach the stock muffler mounting bracket to the frame of the motorcycle. Remove the muffler bracket and set it aside. 6. Remove the two rubber grommets and spacers from the stock muffler and the one grommet and spacer from the muffler mounting bracket. Set them aside with the the two mounting bolts, they will be reused during installation. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install a chrome header flange onto the front and rear head pipes. 3. Install the heat shield to the front head pipe using the two hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe with the heat shield attached, to the front cylinder using the stock nuts. Leave them loose at this time. 5. Install the rear head pipe, with the heat shield attached, to the rear cylinder using the stock nuts. Leave them loose at this time. 6. Install the stock rubbber grommets and spacers into the three large holes on the V&H mounting bar (See figure 1). 7. Slide one dog bone shaped nut plate under the bracket that is welded to each muffler. 8. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Do this to each muffler but leave the clamp loose at this time. 9. Install one muffler to the four hole bracket welded to the V&H mounting bar using the two 5/16″ flange bolts (supplied) and leave them loose. (See figure 1) 10. Slip the muffler and mounting bar assembly onto the front head pipe while aligning the grommet holes in the mounting bar with the holes in the frame.

Incoming search terms: