how to install a chrome exhaust tip in a tacoma

You search Auto repair manual PDF how to install a chrome exhaust tip in a tacoma, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install a chrome exhaust tip in a tacoma Direct Download speed 5282 Kb/s

  how to install a chrome exhaust tip in a tacoma Full Version speed 6162 Kb/s



HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

2007 Yamaha V-Star 1300 Classic Straights Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install Nut strip into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install Nut strip into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks. NOTE: To achieve optimum performance from your Hard-Krome exhaust system we suggest installing the Dynojet jet kit for carbureted models

SUZUKI M109 1800 cc EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 10-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System. 6. Remove the dust cover from the solenoid to expose the rotating cam and cables. DO NOT TRY TO ROTATE THE CAM RELATIVE TO THE ACTUATOR SELENOID TO REMOVE THE CABLES; DOING SO MAY DAMAGE THE INTERNAL COMPONENTS OF THE SOLENOID. To remove the cables from the cam, use the slack in the cables obtained in Step 5 to disengage the cable barrels from the cam, see Figure 1. THE DUST COVER WILL NOT BE REINSTALLED. 7. Now prepare the exhaust valve actuator solenoid for reuse. SECURELY HOLD THE CAM TO PREVENT IT FROM ROTATING IN THE SOLENOID. WHILE PREVENTING THE CAM FROM ROTATING, remove the 10 – 32 flange bolt securing it, see Figure 2. Replace the cam with the Cobra supplied cam, BE SURE TO PREVENT THE CAM FROM ROTATING WHEN REINSTALLING THE BOLT, OTHERWISE DAMAGE MAY OCCUR TO THE SOLENOID , see Figure 3. Torque to factory specifications.

Incoming search terms:

SUZUKI M109 1800 cc FRONT/REAR EXHAUST / HEATSHIELD INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 15-11-2010

download
1. Remove the seat and right side fairing cover (with M109 insignia), behind the fuel tank. To remove the fairing, release the plastic peg on top by pushing the center inward and pulling the fairing upwards until the peg releases, remove the M6 button head bolt at the bottom of the fairing. Pull the fairing outward from the rear and upward near the plastic peg to release it. Once it is free from all plastic pegs pull it forward to release it from the bottom of the fuel tank. 2. Remove the right side cover above the exhaust-mounting bracket secured by one M6 button head bolt, retain bolt for later. Remove the chrome steel cover above the exhaust secured by two remaining bolts, (this chrome piece will no longer be used.) Remove the large left rear rubber grommet and flanged steel collar from this chrome piece, to do this press the steel collar out of the rubber grommet first, once the collar is removed push the rubber grommet out of the wire loop on the chrome piece, set collar and grommet aside for later use. 3. Locate the exhaust valve actuator solenoid and harness and disconnect the black 3-prong electrical connector and white 2-prong electrical connector. 4. Remove the socket head bolts securing exhaust flanges to cylinder heads, set these fasteners aside for later use in reassembly. Support the weight of the exhaust system and remove the 2, 8 mm bolts and one 8 mm nut securing the exhaust mounting bracket and exhaust assembly. Keep these fasteners for use later. Remove the stock exhaust system as one complete unit; this includes the stock exhaust bracket, headpipes and muffler, exhaust valve actuator solenoid and cables. 5. The exhaust valve actuator solenoid must now be removed from the stock exhaust-mounting bracket. To perform this, loosen the two nuts securing each cable to the exhaust valve cable-mounting tab, Position A in Figure 1. Make enough slack in the cables so that the ends of the cables’ threaded sheath may be disengaged from the end of the mounting tab. Now remove the two M6 hex head bolts securing the solenoid to the stock exhaust bracket. The stock exhaust mounting bracket, headpipes and muffler and exhaust valve solenoid cables will not be used anymore with the your new Cobra Exhaust System

Harley davidson American Classic Straights on a 1988-2001 VLX 600 Shadow Installation Instructions

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system.
1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install nut strip into slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — DO NOT TIGHTEN NUTS! 8. Install nut strip into slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks.

HARLEY DAVIDSON FRONT AND REAR FENDER TIP TRIM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation GENERAL The original equipment (stock) fender tip lamp assemblies must be removed and the wire(s) must be unplugged or removed as specified in the following instructions. FRONT FENDER TIP REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1994 AND LATER FLT MODELS 1. Refer to the applicable FLT Service Manual. Remove headlamp assembly with housing. 2. Locate the 3-place connector [32 in wiring diagram] through which 12vdc and electrical ground are connected to the fender tip lamp assembly. The connector locations are as follows: FLTC Ultra: Under fuse and circuit breaker block FLHT/C/C-U: On bottom of left outer fairing bracket FLHR: On left front above air suspension valve NOTE Before disassembling the connector in the next step, refer to the applicable wiring diagram and check wire colors and connections to assure that connector [32] has been located. 3. Refer to the “DEUTSCH ELECTRICAL CONNECTOR” section in the FLT Service Manual and remove the leads, connected to the fender tip lamp, from the socket half, connector [32B]. 4. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 5. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wires connected to lamp assembly. 6. Reach under left side of fender and gently pull wires through rear hole in left side of fender and then through clips on left side of fender and finally through front hole and out of trim strip. REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1993 AND EARLIER FLT MODELS, FLSTC AND FLSTN 1. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 2. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wire connected to lamp assembly. 3. Unplug wire connector located about 3 in. from lamp assembly. Cover the socket half of connector (connected to motorcycle wiring) with electrical tape. INSTALLING FRONT FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in fender and guide outer ends of fender tip trim into trim strips on sides of fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs . REAR FENDER TIP REMOVAL OF STOCK REAR FENDER TIP LAMP ON ALL MODELS Follow steps 1 through 3 given above for “1993 AND EARLIER FLT MODELS, FLSTC & FLSTN” INSTALLING REAR FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in rear fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs

Incoming search terms:

BMW K1200 RS/ GT Full Exhaust System Full Exhaust System Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Remove the lower fairing. 3. Unscrew the O 2 sensor. Remove the stock exhaust system at the rear canister support bracket and where it bolts to the engine. CAUTION -the stock exhaust is very heavy, be careful not to drop it! Also, be careful not to damage the engine sensor located near the front header pipe. 4. Pry out the old exhaust port gaskets and replace with new BMW OE (x4) exhaust port gaskets. Adab of grease will help hold the gaskets in place while you work. 5. Coat the exhaust studs and O 2 sensor threads with high temperature anti-seize compound. 6. Install the TBR headers into the exhaust ports making sure to get a good seat onto the exhaust port gaskets. Next, install the header nuts starting at the rear/outside stud and working your way forward on the outside set of studs. Once that is finished repeat along the inside set of studs. Tighten header nuts only finger tight at this point. 7. Be sure to coat the threads of the sensor with the included packet of hi-temp anti-seize. Install the O 2 sensor into the TBR headers. Turning the sensor in the counterclockwise direction a few times then screwing it clockwise to install will help make it easier to install and prevent the wire from binding. 8. Place a bead of the hi-temp sealant on the outside edge of the headers that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 9. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) Attach it to the canister support bracket using the stock BMWhardware. Both tabs of the canister clamp should be located on the inside of the canister support bracket. Leave loose for the moment. 10. Make sure everything is lined up and start to evenly tighten up the header nuts to BMWfactory torque specification. Tighten the canister support hardware and install the springs as well. 11. Start the bike and check for leaks around the exhaust ports and the header/canister junction. 12. Reinstall the lower fairing

1999-2007 Yamaha V Star 1100 3" Res-Tec Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove O2 sensors from each muffler and cover with supplied cap plug. 3. Loosen clamps at mufflers. 4. Remove bolts that are holding mufflers at rear mounting bracket. 5. Remove mufflers. 6. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 7. Remove rear pipe assembly. 8. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 9. Remove front pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks

Yamaha Stratoliner 2006 3" Big Straights REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 02-01-2012

download
1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding muffler at rear mounting bracket. 3. Remove Cables from exhaust valve. 4. Remove O2 Sensor from pipe. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 7. Remove complete pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install O2 Sensor onto front pipe and install front pipe onto front cylinder, taking care to not scratch chrome surfaces on pipe, engine or motorcycle. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe onto rear cylinder. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — (Remove chrome plastic valve cover to access top nut) — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration.

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

Incoming search terms: