how to install a fan switch on 2510 mule

You search Auto repair manual PDF how to install a fan switch on 2510 mule, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install a fan switch on 2510 mule Direct Download speed 5282 Kb/s

  how to install a fan switch on 2510 mule Full Version speed 6162 Kb/s



Harley-Davidson CHROME HANDLEBAR SWITCH CAP KITS installation and REMOVAL manual

0

Filed Under (Harley Davidson) by admin on 09-03-2012

download
1. Open or remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove left and right-hand switch housing assemblies. Refer to HANDLEBAR SWITCHES in Service Manual. NOTE It is not necessary to disconnect the switch wiring to replace the switch caps. 4. Remove individual switches from switch housing. Refer to SWITCH REPAIR/REPLACEMENT in Service Manual. INSTALLATION Upper Housing Switches 1. For HORN and START switch caps, release torsion spring leg from hole in switch cap tab. Take note of how the spring is installed. The other leg of the spring can remain in the switch bracket hole. 2. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on left side of switch. -J02633 1 of 5 5 2 1 1 3 4 is 01405 1. Switch cap installed correctly 2. Switch cap removal from splined shaft 3. Switch cap removal from pivot pin 4. Switch cap installation onto pivot pin 5. Switch cap installation onto spined shaft Figure 1. Switch Cap Removal and Replacement 3. Pry the switch cap up and away from pivot pin (3) on right side of switch, and remove cap. NOTE Use the clear protective cover film to protect the chrome surface of the switch caps during installation. Remove the film after the installation is complete. 4. See Figure 5. Select proper chrome replacement switch cap from kit. 5. See Figure 1. Place cap onto switch, angling the hole on right side over pivot pin (4) on switch. 6. Carefully press switch cap down onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 7. For HORN and START switch caps, insert torsion spring leg into hole in switch cap tab. 8. Toggle switch back and forth, checking for proper opera- tion. Turn Signal Switches 1. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on switch. 2. Pry the switch cap up and away from pivot pin (3) on switch, and remove cap. 3. Select proper chrome replacement switch cap from kit. Peel a clear protective installation cover from the sheet and place it over the surface of the cap. 4. See Figure 1. Place cap onto switch, angling the hole on top over pivot pin (4) on switch. 5. Carefully press switch cap onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 6. Toggle switch back and forth, checking for proper opera- tion.

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO COMMUNICATION SWITCH KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 2. Refer to the instructions included with the Advanced Audio Hands Free Phone Interface, CB Radio or Intercom Kit, and proceed with that installation until the installation of the items in this kit is called for. 3. Remove the outer fairing and windshield. Refer to OUTER FAIRING/ WINDSHIELD REMOVAL in the Service Manual. 4. On the fairing cap, remove the inner left side hole plug. See Figure 1 and the FAIRING CAP SWITCHES (FLHTC/U) section in the Service Manual. Install the fairing speaker switch (4) in the opening as follows: If a cruise control switch IS present: Follow the instructions in the Service Manual to install the speaker switch. If a cruise control switch IS NOT present: a. Obtain the speaker switch adapter wire (5) from the kit, and the butt splice connector included with the speaker switch. b. Refer to SEALED BUTT SPLICE CONNECTORS in the Service Manual. Splice the adapter wire to the black/ green speaker switch lead. c. Insert the terminated end of the adapter wire into cavity 12 of the fairing cap switch connector [105B] 5. Remove the original equipment left-hand control switch assembly per the HANDLEBAR SWITCHES, REMOVAL, LEFT HANDLEBAR CONTROLS instructions in the Service Manual. 6. Install the new left-hand control switch assembly (3) from the kit. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 7. ALL models: Install the console pod assembly (1), and route the harness forward into the fairing per the instructions packaged with the Advanced Audio Hands Free Phone Interface, CB Radio or Intercom Kit. Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a) • Be sure the wires do not pull tight when handlebars are turned fully to left or right fork stops. 8. Unless already installed, install the overlay harness per the instructions packaged with the Hands Free Phone Interface, CB Radio or Intercom Kit. 9. Refer to the Service Manual and follow the instructions given to re-install the Maxi Fuse

HARLEY DAVIDSON ENGINE GUARD-MOUNTED FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
VRSC models: See Figure 3. Place the wire harness from the kit into the area in front of the battery. Do not block the air intake opening. All models except VRSC and 2004 and later XL models: See Figure 4. Install the wire harness from the kit. Place the relay in the opening of the frame under the seat area, and route the long leg of the harness forward along the frame backbone. 2004 and later XL models: See Figure 5. Remove the nuts retaining the ignition module (1) and temporarily reposition the module as shown. Place the relay in the recessed area (2) of the oil reservoir. Install the ignition module. Route the long leg of the harness along the frame backbone. CAUTION 1 WARNING -J02798 Figure 3. Install Fog Lamp Wiring Harness (VRSC Models) Place harness into this area but do not block air intake Air intake i04372 Battery Figure 4. Install Fog Lamp Wiring Harness (All Models Except VRSC. Dyna Model Shown) i02286.eps 1. Relay 2. Ground stud 3. Long leg of harness 2 1 3 2 of 6 Figure 2. Fog Lamp Wiring Harness Figure 1. Fog Lamp Schematic Ground To low beam To main circuit breaker Fuse N.O. Contact Switch Coil Fog lamp Fog lamp i01360a Relay 1. Fuse block 2. Relay 3. Connector to power 4. Ring terminals (Ground) 5. To fog lamps 6. Unterminated wire to low beam 7. Switch with boot and bracket 4 2 5 6 7 1 3 i05708 5. All 2003 and earlier models and VRSC: Cut the connector from the white power lead, and replace it with the ring terminal supplied in the kit. 6. All 2003 and earlier models, except VRSC: Connect the white wire with the ring terminal to the copper stud (BAT) terminal of the main circuit breaker. All 2004 and later models, except VRSC: Connect the white wire with connector to the B+ connector on the harness. All VRSC: Connect the white power lead to the battery positive terminal. 7. See Service Part illustration. Connect the black ground wires with the two ring terminals to the ground stud under the seat, or at any good electrical ground point. Secure the kit harness to the adjacent harnesses with cable straps (item 6) from the kit. When routing wires through the front fork, make sure the wires are clear of moving parts, to avoid pinching and possible short circuits. 8. Route the forward end of the harness past the steering head, and route the lamp switch leg of the harness along the left side of the handlebar to the clutch control. 9. See the Service Parts illustration. Obtain the switch mounting bracket (item 11) from the kit. Unscrew the boot from the lamp switch, and install the switch into the bracket. Replace the boot on the switch. NOTE If the boot becomes worn or damaged, or is lost, replace the boot to prevent moisture from entering the switch. See the Service Parts illustration (Item 12). 10. See Figure 6. Remove the lower screw (1) and washer from the clutch control clamp (3), and install the lamp switch and bracket assembly (2). Install the screw and washer and tighten to 60-80 in-lbs (7-9 Nm). 11. See the Service Parts illustration. Secure the lamp switch leg of the harness to the handlebar using the wire harness retainers already on the bike. Snap the retainers into the holes in the handlebar. 12. Remove the headlamp assembly. See HEADLAMP – REMOVAL instructions for the correct model in the Service Manual. CAUTION 3 of 6 -J02798 Figure 6. Install the Lamp Switch on the Clutch Control Clamp i04370 3 1 1. Lower clamp screw 2. Lamp switch and bracket assembly 3. Clutch control clamp 2 Figure 5. Install the Wiring Harness (2004 and Later Models) i05712 3

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

HARLEY DAVIDSON VRSC FUEL TANK SIDE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Note the left and right areas on frame where the covers will be installed. Using a 50/50 mixture of isopropyl alcohol and water, thoroughly clean the frame tubes surrounding the fuel cell on the left and right sides. Let dry completely. 2. Unlock and open seat. NOTE Loosening the ignition/light switch screw (in the following step) will allow much easier alignment of the ignition/light switch cover and ignition/light switch during installation. 3. See Figure 1. At area inside of frame rail just above the ignition/light switch housing, loosen the ignition/light switch screw just enough to allow the ignition/switch switch to move slightly from side to side and up and down. Do not completely remove screw 4. See Figure 4. Obtain the right side cover bracket (ignition/light switch side) from kit. 5. Remove the strips protecting the adhesive at all of the raised sections on the cover. 1 2 is 02045 1. Ignition/Light Switch Screw 2. Ignition/Light Switch Figure 1. Loosen Ignition Switch Assembly 6. See Figure 2. Carefully align the right side cover between the three frame tubes. Beginning with the left portion of the cover, press the cover between the upper and lower frame tubes until the raised portions of cover (with adhesive) begin to snap into place. While carefully aligning the right portion of the cover, move the ignition/light switch as necessary until centered within hole in cover, then firmly press into place. Adjust ignition/light switch until the switch is centered within cover. Make sure all raised locations (with adhesive) are firmly contacting the upper and lower frame tubes and that cushion rests against front vertical frame tube. 7. See Figure 1. Tighten the ignition switch screw to 6-10 Nm (53-88 in-lbs ) . NOTE The right side (ignition/light) switch cover surface can be damaged by the key fob (from vibration) when the key is in the ignition and the bike is running. You can either remove the key fob so it does not damage the cover surface, or you can install the plastic clear sheet (included in kit) onto the side cover for protection. 8. If desired, perform the following to install the plastic clear cover onto the ignition/light switch cover. a. Obtain the plastic (rhino) sheet and hold up to the switch cover to determine proper orientation and spacing. b. Carefully peel the adhesive backing from the plastic sheet and position onto the cover. Use a wet sponge, and working out from the center, rub out any bubbles or overlapped areas under the sheet. Allow to dry completely.

2000-2010 KTM X2 SWITCH WIRING HARNESS Removal and Installation Manual

0

Filed Under (KTM) by admin on 25-01-2012

download
The included 3600-SWHA switch harness is intended for use with offroad models that do not come with a Hi/Low beam switch from the factory. The harness is compatable with stock AC lighting electrical systems as well as high output DC electrical systems. 1. Remove the stock numberplate or headlight. Remove the stock kill switch from handlebars and replace with the 3600-SWHA switch. 2. Remove the gas tank. Route the white and black leads from the 3600-SWHA under the tank following the wires from the stock kill switch. Disconnect the stock kill switch bullet and connect the white wire of the 3600-SWHA to the wiring harness. Disconnect the stock kill switch ring terminal and connect the ring terminal of the 3600-SWHA. Fully remove the stock kill switch. Be sure all the wires are safe from being burned or pinched and re-install the gas tank. 3. Disconnect the two female spade terminals from the stock headlight switch (if present). Connect the terminal with the yellow wire to the red power lead from the switch. Connect the white wire to the blue accessory output from the switch. Be sure the clear silicone sleeves are covering the stock plastic housings. 4. Connect the X2 headlight to the switch headlight plug. Note: The stock headlight plug will not be used for the X2 installation, but is still functional for connecting the stock headlight. The stock plug will turn on and off with the new headlight switch, and will be powered in either of the Low or High Beam positions

2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

2008 SUZUKI GSX 1300 RK IGNITION SWITCH INSPECTION/ REPLACEMENT

0

Filed Under (Suzuki) by admin on 29-11-2010

download
INSPECT ROUTING 1. Remove the upper and lower meter panels (refer to Service Manual page 9D-15). 2. Check if the ignition switch lead wire is clamped and routed correctly. Incorrect positions are shown in Figures 1 and 2. Correct routing and clamping is shown in Figures 3 and 4 on page 5. REROUTING 1. Reroute the ignition switch lead wire correctly (Figure 3 and Figure 4). The ignition switch lead wire should not be covered by the other wire harnesses. 2. Turn the handlebars back and forth to verify that the steering operates smoothly and the wiring harness does not become kinked or pinched. 3. Proceed to PUNCH MARK AT VIN on page 8. from the motorcycle (refer to Service Manual page 1H-12). Remove the two black plastic covers to access the cylinder cap mounting bolts (Figure 5). Note: The black plastic covers will not be reused. Secure the mount area (bottom) of the ignition switch in a vise (Figure 6). NOTE: Turn the ignition switch to the OFF position and remove the key from the ignition switch before disassembling the switch. Remove the two “break-off” screws from the ignition switch using the special screwdriver. Set the stepped end of the sleeve on the special screwdriver facing toward the “break-off” screws (Figure 7). Strike the special screwdriver 5 to 7 times with a hammer to produce a deep enough groove on the screw head for the screwdriver to work properly (Figure 6). Pay attention not to hit other parts with the hammer. Turn to remove the “break-off” screws in a counterclockwise direction. If the groove becomes damaged, make another groove at a 90o angle to the original groove. Remove the ignition switch from the vise and hold it upright over the workbench and carefully remove the cylinder cap (Figure 8). NOTE: Pay close attention to the order and orientation of the ignition switch parts during disassembly. REPLACEMENT OF IGNITION SWITCH (Customer Sold Units/Dealer Demo Units- Only If Inspection Shows Incorrect Routing And Unit Has Been Ridden) New Ignition Switch Disassembly 2.

YAMAHA FZR 400 ELECTRICAL CIRCUIT DIAGRAM

0

Filed Under (Yamaha) by admin on 29-11-2010

download
CHECKING OF SWITCHES Check the switches for the continuity between the terminals to determine correct connection. Read the following for switch inspection. SWITCH CONNECTION AS SHOWN IN MANUAL The manual contains a connection chart as shown left showing the terminal connections of the switches (e.g., main switch, handlebar switch, brake switch, lighting switch, etc.) The extreme left column indicates the switch positions and the top line indicates the colors of leads connected with the terminals in the switch component. “C’&-0″ indicates the terminals between which there is a continuity of electricity; i.e., a cl.osed circuit at the respective switch positions. In this chart: “R and Br” and “L/W and L/R” are continuous with the “ON” switch position. “B and B/W” is continuous with the “OFF” switch position. “B and B/W” is continuous with the “LOCK” switch position. “B and B/W” and “R and L/R” are continuous with the “P” switch position. CHECKING SWITCH FOR TERMINAL CONNECTION Before checking the switch, refer to the connection chart as shown above and check for the correct terminal connection (closed circuit) by the color combination. To explain how to check the switch, the main switch is taken for example in the following

Incoming search terms: