download
1. PRELIMINARY: 1.1 Remove the six 6 mm. screws and plastic skid / splash shield from the bottom front of the vehicle frame. (These bolts and plastic skid / splash shield will not be reused snow plow mounting frame installed onto the vehicle.) 1.2 If the vehicle has the Kawasaki optional brush guard installed, it will have to be removed and then reinstalled after the snow plow mounting frame is installed. (The brush guard will fit with the snow plow mounting frame installed first.) 2. VEHICLE MOUNTING FRAME 2.1 Position the vehicle mounting frame (13) under the front of the vehicle so that the six holes (with pipe spacers) line up with the six 6 mm. threaded holes that the plastic skid / splash shield was attached with and the upper plate is through the large oval hole in the vehicle plastic fascia. Fasten loosely using 6mm. x 1.0mm. x 30mm. bolts (33) , 6mm. lock washers (35) and 6mm. flat washers (34). 2.2 Place a 5/16″-18 “U” bolt (36) around the front cross tube behind the plastic fascia and through each set of holes in the flange of the upper plate of the vehicle mounting frame (total of two “U” bolts). Fasten loosely using 5/16″flat washers (41), 5/16″ lock washers (40), and 5/16″-18 nuts (42). 2.3 Install a 5/16″-18 “U” bolt (36) around the lower frame tubes and through each set of slotted holes in the lower plate of the vehicle mounting frame (total of four “U” bolts). Fasten loosely using 5/16″ flat washers (41), 5/16″ lock washers (40), and 5/16″-18 nuts (42). 2.4 Tighten all the fasteners holding the vehicle mounting frame to the vehicle starting with the 6mm. bolts

download
Prior to installing the plow mount the vehicle must be prepped. If not already done so, install a WARN winch kit. Roller fairlead that comes with the winch kit does not need to be installed. This kit comes with a special fairlead to be used with plow. 2. Begin by locating and removing the two rear bumper mounting bolts. See Figure 1 and 2. Figure 1 Location of bumper bolts to remove Figure 2 Remove bumper bolts, both sides Location of bolt to remove WARN® INDUSTRIES PAGE 5 72171 Rev A0 4. Loosely install the mounting brackets to the vehicle using the 7/16″ hardware in the rear replacing the bumper mounting hardware removed in step 2. Do not tighten. See Figure 4 and 5

download
Mount Installation Note: There are different hole locations on the plow mount depending on the bike model. For Prairie 360 use the middle hole locations (B), for Prairie 650 and Twin Peaks 700 use hole locations (A) on mounting plate, as shown in Figure 1. Figure 1 Hole Locations WARN INDUSTRIES PAGE 3 67954 Rev A3 To install the plow mount to the underside of the vehicle install the front two U-bolts PN 60869, and loosely tighten the 5/16″ nuts. Pull the plow mount back in the furthest position and then fully tighten, as shown in Figure 2. For the Kawasaki Prairie 360 use the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (B) . For Kawasaki Prairie 650 and Suzuki Twin Peaks 700 drill a 3/8″ hole through the aluminum skid plate, using the plow mount as a template, as shown in Figure 3. Repeat the same process on the other side. After both holes are drilled attach the mounting plate with the second set of U-bolts PN 61262 and securely tighten around the frame in hole location (A) . Tighten all fasteners securely. Torque 5/16″ Bolts: 20ft. lb.

download
INSTALLTION INSTRUCTIONS – Mule 600/610 (4010 Trans skip to pg 4) 1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figure 1 Below – place UTV Roof Mounting Brackets around roll cage bar and using a marker, mark the position of the holes needed in the roof for each Roof Mounting bracket . Figure 1 Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in where mounting brackets are positioned to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figures 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 2. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

download
Remove the main seat and the passenger seat 2. Remove the tail cover by removing the two bolts. 3 Place the Power Commander in the tail section and route the wiring harness on the inside of the tail section towards the front of the bike (Fig. A). 4. Remove the fuel tank. 5. Remove the air box lid by removing the 8 screws around the outer edge (Fig. B). 6. Remove the bolts shown in Fig. C. This will allow you to remove the air box. Fig. A Fig. B Fig. C i212-411 2004-2005 Kawasaki ZX10R – PCIII USB – 2 i212-411 www.powercommander.com Remove these bolts Remove screws Remove bolts 7. Locate the Throttle Position Sensor connector. This connector is located above the left hand side of the engine. This is a white 3 pin connector. Unplug this connector (Fig. D). 8. Plug the white connectors from the PCIII in-line of the stock TPS connector (Fig. E). 9. Locate the fuel rail connector behind the injector bodies (Fig. F). This connector is brown in color