how to install harley davidson boom handlebar speakers

You search Auto repair manual PDF how to install harley davidson boom handlebar speakers, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install harley davidson boom handlebar speakers Direct Download speed 5282 Kb/s

  how to install harley davidson boom handlebar speakers Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLAME HANDLEBAR GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVE AND INSTALL THE LEFT GRIP 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar 2. Using a T25 TORX® drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX® drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9 Nm) . 9. Using a T25 TORX® drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4- 5.4 Nm) . 5 3 1 1 4 2 2 is00735 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger flange Figure 1. Left Handlebar Switch Housing REMOVE AND INSTALL THE RIGHT GRIP NOTE Right handlebar switch removal requires a Service Manual for your model and year of motorcycle. A Service Manual can be purchased from your Harley-Davidson Dealer. 1. Refer to the RIGHT HANDLEBAR SWITCH section of the Service Manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLE CONTROL section of the Service Manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the Service Manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HARLEY DAVIDSON SLOTTED HANDLEBAR RISER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION NOTE Cover the fuel tank with a clean shop towel to prevent scratching. Damage to the finish could result. 1. Remove the two hex head cap screws and split lock- washers on the underside of the upper fork bracket that hold the currently installed risers in place. Discard the screws, but retain the lockwashers for re-assembly. Retain all additional hardware components that become dislodged from the riser when the screws are removed. 2. Remove and discard the four screws that fasten the currently installed handlebar upper clamp(s) to the risers. Remove and discard the clamp(s). Remove the handlebar from the risers, and carefully allow the handlebar to rest on the fuel tank. 3. Obtain the new slotted risers (1) and hex head cap screws (2) from the kit, and the split lockwashers and hardware components removed in Step 1. NOTE The upper cup washer (A) must be oriented with the flat side up , and the lower cup washer (D) with the flat side down . The ground wire (G) and internal tooth lockwasher (H) are mounted to the right-side riser. 4. Refer to Figure 1 for the correct orientation and reassembly sequence. Install the new risers onto the upper fork bracket using the saved hardware and new screws. Snug the riser screws, but do not fully tighten at this time. 5. Center the handlebar on the risers. To make sure that the handlebar is centered, verify that the knurled areas on the outboard side of each riser are equal. 6. Position the new handlebar upper clamps (3) from the kit, and install with new hex socket head screws (4). Snug the upper screws, but do not fully tighten. Improperly aligned handlebars can contact the fuel tank when turned to the left or right. Contact with the fuel tank can cause cosmetic damage. (00372a) 7. Slowly turn the front wheel to the full right fork stop and then the full left fork stop to be sure the handlebar does not contact the fuel tank. If contact occurs and the handlebars are properly centered, raise the handlebar angle as necessary until proper clearance is attained. 8. Tighten the upper handlebar-clamp screws as follows: a. Tighten the front screws to 12-15 ft-lbs (16-20 Nm) . b. Tighten the rear screws to 12-15 ft-lbs (16-20 Nm) . c. Tighten the front screws to 12-15 ft-lbs (16-20 Nm) . NOTE The gap between the upper clamps and the risers should be equal at the front and rear of the handlebar after tightening. 9. One at a time, remove the riser bolts installed in Step 4. Apply two drops of Loctite® 271 (Red) to the bolt threads and re-install. Tighten the riser bolts to 50-60 ft-lbs (68-81 Nm)

Incoming search terms:

HARLEY DAVIDSON FAT HANDLEBAR RISER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
INSTALLATION NOTES The upper cup washer (A) must be oriented with the flat side up and the lower cup washer (D) with the flat side down. See Figure 1 for the following procedure. 1. Align the components as shown, and install the risers (2) to the upper fork bracket. The ground wire (G) and the internal tooth lock washer (H) are located on the right side only. Do not tighten the riser mounting screws (I) at this time. 2. If an appropriate Harley-Davidson 1-1/4 inch handlebar has not been installed, install one according to the Instruction Sheet included with the kit, or re-install the handlebar assembly onto the risers. 3. Loosely install riser caps (1) onto the handlebars and risers using four socket head screws (3) as shown. 4. Ensure that the risers stay properly aligned with the handlebar and tighten the riser mounting screws (I) to 50-60 ft-lbs (68-81 Nm) . 5. Adjust handlebar to the desired position, ensure that it is centered on the risers, then, starting with the front screws, tighten the four socket head screws (3) to 12-15 ft-lbs (16- 20 Nm) . 6. Turn the handlebars full right and left. Check that: •The handlebars and triple tree clamps do not contact the fuel tank. •The steering stops function properly. •The wiring and brake line are not pinched or kinked in the steering assembly. •Throttle returns from full open to close at both fork stops. Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) •If you are installing different handlebars, measure the change in distance that will be required from the end of the stock brake line to the brake master cylinder. •Compare this revised length to the brake line provided in your kit. •If the line is more than 2.0 in. (50.8 mm) longer or more than 1.0 in. (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct brake line length

Incoming search terms:

HARLEY DAVIDSON CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT GENERAL Kit Number 56032-08 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only). This kit does not fit models equipped with a hydraulic clutch, handlebar mounted gauges or the Road Tech® Radio. Additional Parts or Accessories Required Separate purchase of additional parts or accessories is required for proper installation of this Handlebar Kit on this model motorcycle. Please see the P&A retail catalog or the Parts and Accessories section of for a list of required parts or accessories for this model. For Australia, Brazil, England, Europe and Japan, two special screws (Part Number 2935A) will also be required. Tools and Supplies Required Loctite® 271 Threadlocker and Sealant – Red (H-D Part Number 99671-97) is required for the proper installation of this kit. Fresh, uncontaminated DOT 4 brake fluid from a sealed container will also be needed. Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) For models that retain the original brake line, the two brake- line gaskets found at each banjo fitting must be replaced . Refer to the appropriate parts catalog or see a Harley-Davidson dealer for the correct part numbers. Motorcycles equipped with a glued left-side hand grip will also require a new grip, sold separately. Refer to the parts catalog for replacement stock hand grips. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory hand grips that are available. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for this year and model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 6 and Table 1. INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills)

Incoming search terms:

HARLEY DAVIDSON CHROME HANDLEBAR CLAMP BOLT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION Improperly aligned handlebars can contact the fuel tank when turned to the left or right. Contact with the fuel tank can cause cosmetic damage. (00372a) NOTES Check that the handlebar is centered on the risers. To make sure that the handlebar is centered, verify that the knurled areas on the outboard side of each riser are equal. Slowly turn the front wheel to the full right fork stop and then the full left fork stop to be sure the handlebar does not contact the fuel tank. If contact with the fuel tank occurs or the handlebars are not properly centered, see Figure 1. Slightly loosen the four upper clamp screws, and center the handlebar or raise the handlebar angle as necessary until proper clearance is obtained, then temporarily snug the screws, but do not fully tighten. 4 1 2 3 4 is00868 1. Upper clamp 2. Screw (4) 3. Handlebar 4. Handlebar risers (2) Figure 1. Handlebar Clamp Hardware 1. Remove and discard screws (2) that fasten upper clamps (1) to handlebar risers (4). Save washers under screw head for later use. 2. For Kit 94453-04: Select new chrome screws from the kit that match the length of the screws removed. For all other Kits: Select new chrome screws from the kit. 3. Slide washers previously removed onto screws, and thread screws through the upper clamps into risers. -J03586 1 of 2 4. If handlebar adjustments were made, snug screws but do not fully tighten. a. The bottom surfaces of upper clamps are offset, creating a gap between the clamp and riser on one side. b. Tighten clamps so the gaps appear to the rear of the handlebar, then tighten screw to 12-15 ft-lbs (16.3- 20.3 Nm). 5. If handlebar adjustments were not made, tighten screws to 12-15 ft-lbs (16.3-20.3 Nm). SERVICE PARTS

HARLEY DAVIDSON PULLBACK RISER KIT FOR 1.25-INCH HANDLEBARS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVAL NOTES Cover the fuel tank with clean shop towels to prevent scratching. If replacing the handlebar, refer to the service manual to remove controls, hand levers, handlebar and risers. If only the risers are being replaced, proceed as follows: 1. Remove the two hex head cap screws and split lock- washers on the underside of the upper fork bracket that hold the currently installed risers in place. Discard the screws, but retain the lockwashers for assembly. Retain all additional components from the riser assembly when the screws are removed. 2. Remove and discard the four screws that fasten the currently installed handlebar upper clamp(s) to the risers. Remove and discard the clamp(s). Remove the handlebar from the risers and carefully set the handlebar on the fuel tank. INSTALLATION NOTES See Figure 3. The upper cup washer (A) must be oriented with the flat side up and the lower cup washer (D) with the flat side down. 1. See Figure 3. Align the components as shown, and install the risers (2) to the upper fork bracket. The ground wire (G) and the lock washer (F) are located on the right side only. Do not tighten the riser mounting screws (4) at this time. 2. If an appropriate Harley-Davidson 1-1/4 inch handlebar has not been installed, install one according to the Instruction Sheet included with the kit, or install the handlebar assembly onto the risers. 3. Loosely install riser caps (1) onto the handlebars and risers with the Bar & Shield toward the front of the motorcycle (Figure 1, Item 1). Install four socket head screws (3) with four washers (6). 1 is05253 1. Bar & Shield (install toward front of motorcycle) Figure 1. Bar & Shield on Riser and Cap 4. Check that the risers stay properly aligned with the handlebar and tighten the riser mounting screws following the instructions in the service manual. 5. Adjust handlebar to the desired position, verify that it is centered on the risers, then tighten the front socket head screws (3) to 12-15 ft-lb (16-20 Nm) . There should be no gap at the front of the risers.

Incoming search terms:

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Incoming search terms:

HARLEY DAVIDSON BOOM! AUDIO MUSIC AND INTERCOM KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Intercom system flash (H-D Part No. 76441-06DT) Non-Ultra Overlay Harness (H-D Part No. 70169-06) NOTE For a more integrated appearance of the rider headset connector, the console may be replaced using an Ultra Classic Electra Glide console and/or console pod. See FLHTCU parts manual for applicable parts, and service manual for installation instructions. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 7 and Table 2. REMOVAL 1. Refer to the service manual and remove the following: a. Main fuse. b. Outer fairing. c. Seat. d. Fuel tank and console. e. Inner fairing cap. f. Wire trough cover. g. Left hand control. h. Left side saddlebag. INSTALLATION Install Switch Housing on Passenger Headset Harness 1. See Figure 1. Install push-to-talk switch housing (2) to passenger headset plug housing (3), included as part of passenger headset wire harness (see Figure 7, Item 6). 2. Position the switch housing so the knob is located close to the flip cap on the passenger headset connector. 3. Install self-tapping screws (1) to the switch housing but do not fully tighten at this time. Location adjustment may be required based on the motorcycle model, seats and accessories installed on the vehicle Secure Headset Connector and Switch Housing 1. 2006-2008 FLHX, FLTR, FLHT/C models: For motorcycles WITHOUT docking hardware, See Figure 7. Use the fender support cover fastener to install the smaller P-clamp (11) from the kit. For vehicles WITH docking hardware, use the front docking point fastener. Install the smaller P-clamp (11) between the outside face of the docking point behind the screw and washer. 2009-later FLHX, FLTR, FLHT/C models: For motorcycles WITHOUT docking hardware, see Figure 2. Use the threaded hole in the frame using screw (4), washer (3), spacer (2) and the smaller P-clamp (5) from the kit. For motorcycles WITH docking hardware, use the docking point shown in Figure 3. Install the smaller P-clamp from the kit to the outer end of the docking point using the docking point washer and screw. 2009-later Trike models without the Tour-Pak (FLHXXX): See Figure 4. The headset/switch assembly (1) will be secured to the frame at the location shown using the 1/2- 13 screw (3) and the larger P-clamp (2) from the kit. 2. For ALL models: Once the position of the PTT/VOL switch has been established, securely tighten the self-tapping screws installed to the switch housing earlier.

HARLEY DAVIDSON "LIVE TO RIDE" HANDLEBAR GRIPS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
installation Do not lubricate the left grip of handlebar in any way before installation. This could allow grip to come off while riding which could result in loss of control of vehicle and death or serious injury. 1. Remove existing left handlebar grip by carefully cutting it away from the handlebar using a sharp blade or knife. Remove right grip/throttle sleeve assembly following instructions in appropriate Service Manual. After removal, make sure that left and right handlebar ends are clean and smooth. 2. Check that end caps are securely fastened to grips. Tighten screw inside grip to secure end caps. 3. Assemble new throttle sleeve to handlebar. Refer to appropriate Service Manual for detailed procedure. NOTE Surfaces to be glued must be clean, dry, and free from oil. If surfaces are not clean, dry, and free from oil, then the new application may not adhere as desired. Please observe the following WARNINGS when using the adhesive contained in this kit. FLAMMABLE, INJURIOUS TO EYES, HARMFUL IF SWALLOWED, VAPOR HARMFUL. FLAMMABLE: CONTAINS METHYL ETHYL KETONE. Use only in well ventilated areas. Avoid contact with eyes, mucous membranes, and prolonged skin contact. KEEP OUT OF REACH OF CHILDREN. If swallowed, do not induce vomiting. Call a physician immediately. This product contains a chemical(s) known to the State of California to cause cancer, birth defects or other reproductive harm. 4. Liberally apply a coating of Harley-Davidson Adhesive (Part No. 99839-95) to the inside of left handlebar grip using the cotton swab. Make sure adhesive fully covers all inside surface area of the grip. Also, apply a coat of adhesive to the handlebar end. 5. Check how the rectangular pattern is oriented on the throttle (right) grip. Align pattern on left grip to match right grip and immediately push the new grip completely onto handlebar end. 6. Rotate the end caps so the “Live to Ride”text is positioned at the top of both grips. NOTE Do not hesitate when installing left grip or adhesive will dry before installation is complete. Allow 6-8 hours at 70°F to achieve full cure of the adhesive. Prior to starting engine, verify that the throttle control will snap back to the idle position when released. A throttle control that prevents the engine from automatically returning to idle can lead to a loss of control of vehicle which could result in death or serious injury. Cleaning

Incoming search terms: