how to install harley davidson inner fairing

You search Auto repair manual PDF how to install harley davidson inner fairing, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install harley davidson inner fairing Direct Download speed 5282 Kb/s

  how to install harley davidson inner fairing Full Version speed 6162 Kb/s



HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HARLEY DAVIDSON MULTI-POCKET FAIRING POUCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION 1. Remove the three outer fairing screws located just below the windshield and remove the windshield. 2. See Figure 1 or Figure 2. Apply adhesive pads to the bottom of the bracket in the locations shown. When the bracket is installed, the pads should rest on the top of the inner fairing and support the bracket. 3. Apply clear tape between the screw opening at the base of the windshield on the inside surface of the windshield. 4. See Figure 3. Pull the outer fairing away from the inner fairing to provide sufficient clearance to slide the mounting tabs of the bracket over the top lip of the inner fairing. 5. Center the fairing bracket along the top of the inner fairing. 3 1 2 is04616 1. Bracket 2. Pads 3. Bracket clips Figure 1. Bottom of 3-Pocket Fairing Pouch Over tightening windshield fasteners can crack windshield and/or fairing. (00451b) 6. Reinstall the windshield and three screws removed in Step 1. Tighten screws snugly, but be careful not to over-tighten screw or the fairing may crack. 3 1 2 is04615 1. Bracket 2. Pads 3. Bracket clips Figure 2. Bottom of 2-Pocket Fairing Pouch 4 2 6 5 1 3 is04614 1. Pouch 2. Windshield 3. Tape, clear 4. Outer fairing 5. Pouch bracket clip 6. Top of inner fairing Figure 3. Fairing Clip Attachment, Side View

Incoming search terms:

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

HARLEY DAVIDSON FAIRING BRA INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
This kit is designed for installation on 1996 and later FLHT, FLHTC, FLHTCU AND FLHTCU/I Model Motorcycles. Installation 1. Align each of the sewn-in pockets on the fairing bra with each of the outer edges of the fairing at handlebar level. 2. See Figure 1. Standing in front of the vehicle, remove the three T27 Torx screws (1) with washers securing the windshield along the front of the fairing. NOTE In the following Step, the Chrome Windshield Strip (purchased separately) , will serve as a mounting bracket for the fairing bra 3. Obtain the Chrome Windshield Strip (P/N 59213-96) and screws supplied with strip. While aligning holes in the chrome strip over the bra, install the new screws with washers through the strip and bra, then tighten securely into the windshield. 4. The six straps (three on each side near the bottom) will be captured between the inner and outer fairing. Refer to Figure 1. Remove the four screws (2) from the inner fairing. NOTE: The bottom two screws are below the fairing cap. Save screws for installation. Separate the inner and outer fairings just enough to install the straps into the fairing. Adjust the straps, then reinstall the screws and tighten securely. 5. Remove the Phillips screw located at the bottom of the headlamp trim ring. Save screw for installation 6. See Figure 2. Orient the elastic portion of the bra around the headlamp, however in front of, the retaining ring as shown. 7. Install the bottom elastic strap below the fairing seal under the headlamp. 8. Install the headlamp trim ring using the Phillips screw removed in Step 5.

HARLEY DAVIDSON ILLUMINATED CHROME COVER KIT FOR FAIRING MOUNT MIRRORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION Preparation Models with main fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. Models with main circuit breaker: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. Installation NOTE Cover the work surface with an H-D Service Cover or clean shop towels to prevent scratching the finish of the outer fairing. 1. Remove the outer fairing per the instructions in the service manual. Lay the fairing face down on a sturdy work sur- face. 2. See Figure 2. Remove the mirrors (2), flange nuts (3) and plastic backing plates (4) securing the mirrors to each side of the inner fairing (1), and retain all items 3. Measure one inch (25 mm) straight down (5) from the large mirror stud hole in the inner fairing, and make a mark. 4. Drill a 1/4 inch (6 mm) diameter hole (6) through the inner fairing at the mark. 5. See Figure 1. Obtain a chrome wire collar (3) from the kit, and press it into the new hole from the outside of the inner fairing. Gently tap into place with a soft-faced hammer. 6. Repeat Steps 3 through 5 on the opposite side of the inner fairing. NOTE Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the mirror cover to the mirror. 7. Clean the back surface of the mirrors with the alcohol pad (7) provided. Allow to dry thoroughly. 8. Obtain the primer tube (8) from the kit, and follow the instructions on the tube to activate the primer. When the primer is activated apply the primer to the back surface of one mirror. 3 6 2 1 4 5 is06091 1. Inner fairing 2. Fairing mount mirror 3. Flange nut (2) 4. Plastic backing plate (2) 5. Measure one inch (25 mm) down 6. Drill 1/4 inch (6 mm) hole (2) Figure 2. Fairing Drill for Illuminated Mirror NOTE The Illuminated Chrome Mirror Covers are side-specific. The covers install with the wire harness exiting from the bottom. 9. Obtain the correct mirror cover from the kit. Rub the liners on the three pads on the back surface of the mirror cover to activate the adhesive, then remove the liners. 10. Place the mirror cover over the back surface of the mirror and press into place for a minimum of 60 seconds. 11. Repeat Steps 8 through 10 for the remaining mirror and cover. NOTE The plastic backing plates (removed earlier) are identified with a letter “L” (left) or “R” (right) stamped on the post. The mirrors are marked with a letter “L” or “R” stamped on the swivel block. Use the correct backing plate for each mirror by matching the letters. 12. Position the mirror on the outer face of the inner fairing, with the rounded side of the mirror outboard and the Bar & Shield logo upright. a. Insert the mirror cover wiring harness through the chrome wire collar installed in Step 5. b. Insert the mirror post through the original mirror mounting hole. c. Place the correct plastic backing plate against the inner face of the inner fairing, engaging the two holes in the backing plate with the threaded stud and index pin on the mirror swivel block. d. Install the flange nut on the threaded stud and tighten to 30-40 in-lbs (3.4-4.5 Nm) . e. Repeat for the remaining mirror on the other side of the fairing

HARLEY DAVIDSON VENTED FAIRING LOWERS KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1. See Figure 1. From the kit, obtain the left side fairing lower (1), left side fairing lower cap (2), two flange locking nuts (3) and two stud clips (4). Place fairing lower cap in front of the left side engine guard and left side fairing lower behind engine fairing guard. With both pieces in place around engine guard, install the two flange locking nuts onto the studs clips and hand tighten. Repeat procedure for right side fairing lower. 2. Secure bottom of fairing lower to lower engine guard with round clamp (5) from hardware kit. Position clamp around engine guard with tabs toward rear of vehicle and flat side of clamp against fairing lower and with the rubber washer (6) between clamp and engine guard. Place Torx pan screw (7) through fairing lower, rubber washer and clamp. Secure assembly with flanged locknut (8). Repeat for right side fairing lower. Tighten to 144 in-lbs (16.3 Nm). 3. Tighten all left and right side upper flange locking nuts (3) to 72 in-lbs (8.1 Nm). 4. Install left side door assembly glovebox (9) to fairing lower using the attachment cord (10). Insert glovebox door into fairing lower. Repeat for right side fairing lower. NOTE Do not press reflector firmly into place until you have it positioned in desired location. The adhesive is very strong and once it comes in contact with a surface, it will be difficult to remove without damaging the reflector. 5. Peel adhesive strip off back of reflector from kit. Position reflector on side of front fender above chrome side trim strip and approximately 4 inches rearward from front of fender. Press reflector securely into place. Repeat for opposite side reflector

Incoming search terms:

ROAD TECH ZUMO 660 GLOBAL POSITIONING SYSTEM (GPS) FAIRING MOUNTING KIT INSTALLATION

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the outer fairing and windshield. Refer to the service manual. is05900 Figure 1. Road Tech Zumo Drilling Template Placement 3. See Figure 1. Obtain the drilling template from the kit. 4. Position the template on the back side of the inner fairing, in the upper left corner above the fuel gauge, aligning the template to the top of the inner fairing and the plastic rib as shown. 5. Drill a 5/16 inch (8 mm) diameter hole through the inner fairing per the template. 6. See Figure 4. Position the gasket (2) and GPS mount (1) onto the face of the inner fairing, aligning the upper hole in the mount with the hole drilled in the previous step. 7. Temporarily install one of the screws (4) through the upper hole to help align the GPS mount. 8. See Figure 2. Mark the location of the lower mounting hole on the face of the inner fairing, using the GPS mount and gasket as a template. Mark the location of the wire routing hole using the guide hole (3) in the gasket as a template. 9. Remove the screw, GPS mount and gasket from the inner fairing. 10. Drill a 5/16 inch (8 mm) diameter hole through the inner fairing in the lower mounting location. Drill an 11/16 (17 mm) diameter hole through the inner fairing in the wire routing location. 1 2 3 is06149 1. Gasket 2. Wire routing guide hole and ribs 3. Guide hole Figure 2. Remove Gasket Ribs and Guide Hole 11. See Figure 2. Remove the wire routing guide hole and four ribs (2) from the gasket (1). 12. See Figure 4. Install the GPS mount and gasket to the inner fairing with screws (4) flat washers (5) and locknuts (6). Tighten to 50-60 in-lbs (5.6-6.8 Nm) 13. Obtain cradle with harness from GPS system kit. NOTE The fuse holder on the harness must be opened to fit through the hole. 14. Insert harness through the 11/16 inch (17 mm) diameter hole drilled earlier. 15. Insert the split grommet into the 11/16 inch (17 mm) diameter hole around the harness. Installing the Cradle 1. See Figure 4. Install four bushings (H) from the GPS system kit and insert them into the back of the cradle mounting holes. 2. Position the cradle to the GPS mount. Direct the harness out through the slot (G) of the mount. 3. Insert a button head screw (3) through one of the holes in the cradle and into the corresponding hole in the GPS mount, but do not fully tighten

Incoming search terms:

HARLEY DAVIDSON CHROME INNER PRIMARY HOUSING INSTALLATION INSTRUCTION

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not sold separately Chrome Inner Primary Housing 786A Sealing fastener (5) INSTALLATION NOTES Whenever the sealing fasteners are loosened or removed, they must be replaced. Always replace using Harley-Davidson® Original Equipment sealing fasteners part 786A. Do not use part 786. The primary housing included in this kit installs in the same manner as the stock inner primary housing with the following exception: Use the five sealing fasteners included with this kit. Install and tighten fasteners to the torque specified below. For 2006 Dyna model motorcycles: Remove dowel pins from the chrome inner primary housing before attempting installation. Using a pair of pliers or vice grips, remove the dowel pins by carefully twisting and pulling on the pins. Be careful not to scratch or mar the chrome or sealing surfaces of the chrome inner primary housing. Remove the chain tensioner anchor plate, bolt and screws from the stock inner primary housing after it has been removed, then install it on the chrome inner primary housing. See the appropriate Service Manual for the proper tightening procedure, and torque specifications. 1. See the Drive section of the appropriate Service Manual, and remove the stock inner primary housing. Clean the internal threads in the crankcase and transmission case where the sealing fasteners were removed using a wire brush. Install the chrome inner primary housing as indicated below. Replace the five stock sealing fasteners with the five bolts included in this kit. Put a light coat of primary oil under the head of the sealing fasteners and then tighten to 23-25 ft- lbs (31-34 Nm)

Incoming search terms:

Harley Davidson Electra Glides, Ultra Vent (model LV-2,3,4) Installation Manual

0

Filed Under (Harley Davidson) by admin on 07-03-2012

download
Remove the fairing lower from the engine guard using the procedure provided in your Harley-Davidson user/service manual. Do not remove the glove box from the fairing. Vent Placement, Hole Drilling and Cut-Out: Caution: Place cloth or cushion underneath fairing lower to protect it from getting scratched during the following procedures. LV-2,3,4 Installation Copyright 2003-2004 2 3. Working inside the fairing and using the bottom of the glove box as a guide, position a closed vent parallel to and no more than 1/16″ from the rear edge of the fairing. Position the assembly so that the vent side tabs are no more than 1/8″ below the bottom of the glove box. (You want the vent assembly as close as possible to the glove box but with enough room so that the side tabs do not touch the glove box when the vent is closed! ) Mark the back two holes with a pencil then remove the vent and replace it with the cutting template in the exact same location. See photo to the right to assist in judging the cutting template orientation. 4. Lift out the glove box, steady the template with one hand and using an 11/64″ drill bit carefully drill 1 hole near the back edge of the fairing through the bottom corner hole of the cutting template. Install one screw and nut and tighten slightly to stabilize the template’s location. On the other corner (same edge) , drill the second hole. (You cannot drill the remaining holes from inside the fairing because the front edge of the fairing lower is in the way. ) 5. Remove the screw and nut and re-position the cutting template on the outside of the fairing with the three hole side of the template towards the front of the fairing (away from the edge of the fairing) . Install two screws and nuts into the open holes. Drill the remaining two corner holes and install two screws and nuts. Change drill bit size to 1/8″ to drill the final center latch hole. Next skip down to one of the two following procedures to make the vent opening using either A) Dremel tool/RotoZip router or B) coping saw/frameless hacksaw

Incoming search terms: