how to install led signal relay zx9

You search Auto repair manual PDF how to install led signal relay zx9, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install led signal relay zx9 Direct Download speed 5282 Kb/s

  how to install led signal relay zx9 Full Version speed 6162 Kb/s



HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

motorcycle Turn Signal Conversion Kit Installation Instructions

0

Filed Under (Tips and Review) by admin on 09-11-2010

download
1. Place motorcycle on solid, level ground and on center stand if equipped. 2. Remove your turn signal lens. Place it upside down and clean the lens interior with the supplied alcohol wipe. Allow to completely air dry. Note: the LEDs are mounted to the inside of the turn signal lens with the LEDs making direct contact with the lens. The supplied silicone is used to secure the LED board to the lens. It remains flexible but can be removed. Test fit the board in your lens prior to using silicone. 3. Using a small screwdriver, poke a small hole in the end of the tube of silicone. Place a dab of silicone on each of the 12 LEDs on the circuit board. CAUTION : Note the position of the metal pins on the back of the LED board, They must be located 90 degrees from where the holes are that secure the lens to the housing. See attached diagram. 4. Position the round circuit board over the inside of your turn signal lens with the LEDs facing down. Get the board as centered as possible. Allow the silicone to make contact with the inside of the lens and then push down and slightly rotate the board back and forth to allow the LEDs to make contact with the lens surface. Repeat other side. NOTE : the silicone will require 30 minutes in 70 degree weather to tack up. Full cure will occur within 24 hours. We suggest not riding for several hours if possible to allow the best adhesion. 5. You will need to access the following wires; running light (license plate can be used), brake lights, right turn and left turn. Disassemble the bike as needed to gain access to the wiring. Shop Tip: we have found that on the Yamaha Star Series and the Kawasaki Cruisers that installation is much easier when you remove the turn signal bar from the fender. On the Yamahas, there are 3 bolts holding the moustache in position. The wires will unplug from behind the license plate. On the Kawasakis, unplug the signals under the seat and bend the tabs under the fender to be able to remove the wires. 6. We have provided some tubing to slide over the wires so that when you re-install the bulb socket, our wires for the LED boards will not be pinched. This tube should be slid all the way into the turn signal housing. You may have to shorten the tubing for your installation. 7. You will need to run wires through the stem of the turn signal. You can see samples of how the various manufacturers signal housings come apart on our web site. Click on “Other Lighting Products” and then “Turn Signal Conversion Kits” and follow the link. We suggest placing the removed turn signal assembly on a towel on your work area. 7. You will need to leave 2″ of slack in the wires at the turn signal housing to allow for wire connection. 8. Reinstall the turn signal housing back on the motorcycle if removed. NOTE: both of the run/brake circuits must be used. You may shorten the wires only on the run/brake circuits as needed. Do not change the circuits under the heat shrink. T-Tap instructions. Lay the “donor” wire in the slot in the burgandy connector. Close and snap together with pliars. Strip some insulation off of the wire which will be tapping into the factory wire. Crimp one of the pink connectors on the bare wire and plug it into the burgandy T-Tap 9. Connect the green wires from the run/brake circuits to the bikes running lights. The 2 greens can be connected together. 10. Connect the blue wires from the run/brake circuits to the bikes brake lights. The 2 blues can be connected together. 11. Take one of the red wires from a run/brake circuit and connect it to one of the black with white stripe wires coming from one of the LED boards using the supplied red butt connector. Connect the other run/brake circuit red wire to the remaining black with white stripe wire on the other LED board. 12. Connect the black wire from the LED board on the right side of the bike to the right turn signal positive (+) wire on the motorcycle. 13. Connect the black wire from the LED board on the left side of the bike to the left turn signal positive (+) wire on the motorcycle. 14. Plug the wires into the LED boards. If you hold the turn signal lens so that you are viewing the back of the LED board, position the connectors on the board at the 12 o’clock (top) position. The connector on the left is the positive (+) terminal. Connect the red wire to it. Connect the black wire to the remaining connector on the right side. 15. Check operation. LEDs should come on with running lights. LEDs will brighten when brake lights are applied. LEDs will shut off when the amber turn signal comes on. 16. Should you have any problems, please see the troubleshooting chart on our website.* * 17. Reassemble bike

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HARLEY DAVIDSON FLSTF TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. See Figure 1. Disconnect battery cables, negative (-) cable first. 2 1 is03242 1. Negative (-) cable 2. Tail lamp connector Figure 1. Negative Battery Cable and Tail Lamp Connector 3. See Figure 2. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 2. Remove Tail Lamp Lens 4. See Figure 3. Using a Terminal Pick Tool (1), depress locking tabs and disconnect turn signal connectors (2- place) (2, 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. 6. See Figure 4. Remove turn signal wiring (1, 2) from clips (3) under rear of fender INSTALLATION NOTE Proper installation of kit requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Route Turn Signal Wiring Through Rear Fender and Support 1. See Figure 5. Remove three rear screws (1) from fender support (2). 2. Loosen, but do not remove two front screws (3) from fender support. 1 3 2 is03285 1. Screw, rear (3) 2. Fender support 3. Screw, front (2) Figure 5. Fender Support Screws and Fender Support 3. Pull fender support away from rear fender to gain access to turn signal mount. 4. Remove stock screw and washer from turn signal mount. 5. See Figure 7. Pull turn signal (B) and turn signal mount (A) away from fender support. 6. Remove turn signal and wires from vehicle by routing turn signal wiring and connector through holes in rear fender and fender support. Gently guide wires through holes to ensure they do not get damaged. Feed Wiring and Install Relocation Bracket 1. See Figure 6. Feed turn signal wiring and connector through middle hole in turn signal relocation bracket and under rear of fender support. 1 is04635 1. Wire harness Figure 6. Wire Harness Routing 2. See Figure 7. Insert stock screw and washer through rear hole of relocation bracket (1) and turn signal mount (A). 3. Thread screw into turn signal (B). Tighten to 12-16 ft-lbs (16.3-21.7 Nm). 4. Align relocation bracket (1) with rear of fender support and install with screw (2) and nut (3) from kit. Tighten nut to 12-16 ft-lbs (16.3-21.7 Nm). Complete Turn Signal Relocation Wiring 1. See Figure 5. Install one rear screw (1) to hold fender support in place while routing wiring. Install screw snugly but do not fully tighten

Incoming search terms:

Victory Vegas Rear LED Turn Signal Assembly Installation Manual

0

Filed Under (Victory) by admin on 31-10-2010

download
Step 1 •Prior to installation it is recommended that you perform a Pre-Function check. To do so, remove the left side battery cover from the bike and expose the post terminals. Hold the positive red lead from the turn signal to the positive red lead of the battery and then place the negative black lead from the turn signal to the negative black lead of the battery. Do one side at a time and ensure that both sides light prior to installation. Step 2 •Remove seat (passenger too if installed) •Remove fender “eyelashes” (required first if passenger seat is installed) •Remove the fender mounting bolts •Disconnect the rear turn signal and taillight harness connector located in the battery box compartment •Remove the fender by gentle prying outward and upward on one side to clear the mounting points, then the other side •Set aside on a flat and smooth surface to protect the fender’s finish (you may want to wrap it in a large towel) Step 3 •Turn the rear fender assembly upside down on a stable and covered/protected surface to prevent damaging the fender/paint •Remove the rear tail assembly and disconnect the wiring harness and license plate light. THIS PART IS NO LONGER NEEDED! Victory Vegas Rear LED Turn Signal Assembly Installation Guide •Remove the stock metal spacers shown below and replace them with the ¼” rubber spacers included in your accessory/installation kit. Step 4 •Place the turn signal assembly mounting arms over the rubber spacers. Align the turn signal in place so the space between the fender and the turn signal tube is consistent. After completing this step, place a small amount of Loc-Tite to the bolt and slowly tighten the stock nuts snugly in place, (extreme over-tightening may damage turn signal or fender lip). You should not need to loosen the mounting arms which are attached to the turn signal bracket to obtain the ideal fit; they are pre-assembled to be aligned. Please also note that due to manufacturing tolerances in the production of the fender, the rolled inner lip of it may interfere with the turn signal assembly seating properly. If this is the case, the lip can be tapped down flush with a rubber mallet or other appropriate tool. Take the necessary precautions to maintain your fender’s finish should this step be necessary. Step 5 •Run the wiring of the turn signal assembly in an appropriate/desireable path to the stock wiring harness. See picture below as an example. Once the wires are run, cut any excess wire and install the bullet connectors (included in the installation/accessory package) to the end of the wires. Due to the small gauge of the wire it’s suggested that you double it over before placing it into the bullet connector and solder it in place. Wire as follows:

Incoming search terms:

HARLEY DAVIDSON SPORSTER, DYNA AND SOFTAIL LICENSE / TURN SIGNAL RELOCATOR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate mounting bracket from the fender. Remove the two screws from the tail light lens and pull the light outward, unplug the wire connector and set aside. Unplug the turn signal wire connectors from the tail light base and push them out thru the hole in the fender. Looking up underneath the rear fender remove the wires from the clips that secure them to the bottom side of the fender. Cut the wires 2″ from the plugs as shown in photo 1. 2. Unscrew the signal housings from their mounting stems while rotating the wires on the inside of the fender so as not to twist them off while unscrewing the signal from the stem. Remove the signals pushing the wires thru from the inside while pulling the signal outward. Remove the nuts from the backside of the fender that secure the stems and remove the stems. 3. Assemble the license/turn signal bracket, turn signals. Place the smaller reinforcing bracket inside the license plate bracket. Locate the two supplied 5/16″ X 1″ bolts with holes drilled thru the center and the two supplied 5/16″ long spacers. Place the bolts thru the brackets from the inside, threads facing outward followed by the spacers. Thread the wires of the signals thru the bolts and thread the bolts into the signals and snug the bolts. 4. Mounting the LED lights a. Locate the supplied LED tail/brake lights. NOTE: this license plate holder is designed for the new U.S. standardized 7″ wide license plate. If you have an old style wider plate call us at the phone number below and we will send you a separate set of chrome brackets to work with your larger plate at no charge. b. Install the lights as shown in photos 2 & 3. Thread the wires of the LED lights thru the lower holes in the license bracket, peel the adhesive backing and press them firmly in place. Cut the wires off at about 18″ long. c. Install the license plate bracket with signals and LED lights onto the rear fender as shown in photos 2 & 3. Place the two supplied 1/4″ X 1″ flat head screws thru the license plate mounting block. Notice that the thicker half of the mounting block goes toward the top of the fender. d. Next route all the wires from the right turn signal and LED into the slot or notch on the backside of the mounting block followed by the rubber mounting gasket. Install the two nuts from the underside of the fender (Removed from the original license bracket.) onto the two flat head screws and snug them being sure the wires are all in the slot of the mounting block. Run all of the signal and LED wires thru the hole in the fender to the left of the mounting block. e. Install the license plate assembly onto the mounting block using the two supplied 1/4″ X 1/2″ flat head screws. Check the slack from all the wires and again be sure the wires are not pinched between the mounting block and the fender. Tighten all four flat head screws securely. Align the turn signals and tighten their mounting bolts securely.

HARLEY DAVIDSON CUSTOM TOURING FRONT BULLET TURN SIGNAL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION Outer Fairing/Windshield and Auxiliary Lamp Bracket Removal To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2 3 1 2 is 01215 1. Six-position connector 2. Four-position connector 3. Auxiliary lamp connector Figure 1. Disconnect Signal and Auxiliary Lamp 1. Remove Maxi-Fuse. Refer to SYSTEM FUSES, MAXI- FUSE in Service Manual. NOTE Since the outer fairing screws hold the windshield in place, the windshield may fall to the floor if not removed. 2. Remove the windshield and outer fairing. Refer to UPPER FAIRING/WINDSHIELD in Service Manual for the outer fairing/windshield removal procedure. 3. Disconnect auxiliary lamp and turn signal connectors. NOTE See Figure 1. On 2005 and prior year models, the left and right turn signals plug into a 6-place connector located on the left fairing support brace. On 2006 and later models, each turn signal plugs into its own 4-place connector located toward the bottom of the inner fairing on each side. 4. Using a T40 Torx® drive head, remove and save the four bolts securing the auxiliary head lamp bracket to the chassis. 5. Remove auxiliary lamp bracket from motorcycle. Turn Signal Assembly 1 is 01217 1. Triangular opening Figure 2. Insertion of Terminals Through Triangular Opening 1. See Figure 2. Insert wire terminals through the triangular opening in the turn signal mounting bracket included in the kit. 2. Fit turn signal housing onto bracket. 3. Apply a small amount of Loctite (243) blue (99642-97) to threads of hex head cap screw. 4. Tighten cap screw to 15-20 ft-lbs (20-27 Nm) . -J03753 1 of 2 Turn Signal Installation 1 is 01218 1. Turn signal wire Figure 3. Turn Signal Wire Routing 1. See Figure 3. Insert turn signal connector and wiring between bottom of fairing and top of outer fairing skirt. 2. Route turn signal wire under cutout on mounting bracket and place bracket onto motorcycle. NOTE Care must be taken so the turn signal wire is not pinched between turn signal bracket and motorcycle chassis. 3. Install washers onto turn signal bracket mounting bolts and apply Loctite 243 (blue) (99642-97) to the bolt threads. 4. Tighten mounting bolts to 15-20 ft-lbs (20-27 Nm) . 5. Route turn signal leads toward harness connector. Secure loose wiring with tie straps so wires do not rub against any sharp objects

HARLEY DAVIDSON V-ROD CHROME REAR TURN SIGNAL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Prepare the Motorcycle 1. Remove the right cover and the maxi-fuse. 2. Follow Service Manual instructions to remove the air box cover. Remove the Existing Rear Turn Signals 1. For 2006 and Earlier Models: See Figure 1. Insert a screwdriver into middle of hole of license plate light cover. Push forward to release tail lamp housing retaining clip. 2. See Figure 3. Identify the white left [19] (1) and black right [18] (2) 2 pin rear turn signal connectors. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. To remove the rear turn signal wires from the socket terminal housing, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. 6. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 7. Repeat for the opposite turn signal. 1. For 2007 and Later Models: See Figure 2. Open seat and remove the nut and washer (3), seat post (2), passenger pillion and passenger seat (1) per the instructions in the Service Manual. 2. See Figure 4. Identify the left (1) and right (2) rear turn signal wires and 6 pin rear turn signal connector [94]. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. See Figure 5. Remove the turn signal wires from the 6 pin socket terminal housing. To remove the wires, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. Repeat for all four turn signal wires. Do not remove the license light wires from the socket terminal housing. 6. Gently pull the loose turn signal wires through the sheath toward the rear of the vehicle until completely removed from the sheath. 7. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 8. Repeat for the opposite turn signal

Incoming search terms:

HARLEY-DAVIDSON TURN SIGNAL MIRRORS WITH CONVEX GLASS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
STEP 1 Remove the stock mirrors. LEFT SIDE: STEP 2 Choose the longest Allen bolt from the hardware kit that passes through the hand control, a split lock washer, an internal tooth star washer, the turn signal mount (if applicable), and still provides maximum thread engagement in the mirror stem without bottoming out. Mount the mirror with the hardware listed above. (Place the star washer between the mirror stem and the hand control). RIGHT SIDE: STEP 3 If the turn signals are not mounted under the mirror, proceed in the same manner as the left side. STEP 4 If the turn signal is mounted under the mirror proceed as follows: Apply Red loctite to the short threaded end of the special mounting stud. Screw this end securely into the mirror stem. -cont.- 1432-22HD-0105 TURN SIGNAL MIRRORS WITH CONVEX GLASS 1432 INSTALLATION Illiana CUSTOMER SERVICE 877.370.3604 (toll free) INSTALLATION QUESTIONS techsupport@kuryakyn.com or call 715.247.2983 WARRANTY Küryakyn™warrants that any Küryakyn product sold hereunder, if properly installed, maintained and operated under normal conditions, shall be free from any defects in materials and workmanship for a period of one (1) year from the date the Küryakyn products are sold to the customer. CONSEQUENTIAL DAMAGES: Küryakyn shall not be liable for any consequential or incidental damages. ABOUTOURCA TA LOG You’ll find all our innovations for H-D, GL and Metric Cruisers in our annual catalogs. Order online today-select the “CATALOGS” icon. Each Küryakyn™ product comes with a Proof-of-Purchase good for a complimentary catalog. Details in packaging. Be sure to ask your local dealer about other Küryakynproducts, the motorcycle parts and accessories designed for riders by riders. ©2004 Küryakyn USA™All Rights reserved.
STEP 5 Remove the turn signal assembly from the stock mirror. Pay close attention to how the stock turn signal ball joint assembly comes apart as this will aid in re-assembly. STEP 6 Place a star washer over the mounting stud and insert the mirror and stud assembly into the hand control. Re-assemble the turn signal ball joint being sure the turn signal light is aimed to your liking. You may wish to consult your H-D shop manual when re-assembling this ball joint. WIRING: STEP 7 Determine where you wish to splice into the H-D turn signal wiring harness. Cut the harness or strip back an appropriate amount to vinyl wire covering and prepare the wires for splicing. Make the wire connections as follows: Wires from Turn Signal Mirror H-D Turn Signal Wire Colors Black – (Ground) Black (Ground) Red – (Running Light) Blue (Running Light) White (Turn Signal) Violet (Turn Signal) If a more pronounced flash is desired, one may eliminate the running light function and wire as follows: Black Black Red and White together Violet If these turn signal mirrors are to be used in conjunction with stock front turn signals, no load equalizer will be required. If the turn signal mirrors are REPLACING stock front turn signals, in most cases, a load equalizer is required. For easiest access we suggest installing the load equalizer under the seat; tapping into the main wiring harness that leads to the tail lights and rear turn signals.

Incoming search terms:

HARLEY DAVIDSON AUXILIARY BRAKE/RUN/TURN SIGNAL CONVERTER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery cables, negative side first. 2. Remove the seat according to the procedures in the applicable Service Manual. NOTE Federal regulations require that red turn signal lenses need to be a minimum of 4 inches from the tail or stop lamp, edge to edge. In order to ensure this spacing requirement, new directional stand-offs are provided in kit and must be used to replace the original (stock) directional stand-offs. To install the new directional stand-offs, perform the following. 3. See Figure 1. Insert a small screwdriver into middle hole (1) of license plate light cover assembly (2). Push forward to release tail lamp spring clip. -J03679 1 of 4 2 1 is01493 1. Middle hole 2. License plate lamp assembly Figure 1. Removing Tail/Stop Lamp Assembly 4. See Figure 2. Lift tail lamp assembly upward and disconnect tail lamp connector (1). Disconnect left (2) and right (3) turn signal 2-place connectors. 5. See Figure 3. Remove two left side fender support front socket head screws (1). Save hardware for installation. 6. Remove left fender support capscrew (2) (under fender) near end of support and washer (3). Remove capscrew (4) at approximate midpoint of fender support and washer (5). Save hardware for installation. 7. Remove directional lamp screw (6) and washer (7). NOTE Prior to removing turn signal wires, carefully note routing. In particular, pay close attention to the locations of cable straps which must be replaced. 8. Carefully remove fender support (8), turn signal lamp (9) and directional lamp support (10) along with wiring through elongated hole in fender (11). Discard directional lamp support and cap screw. Save turn signal lamp for installa- tion. 9. Perform Steps 5 through 8 for the right fender support and signal lamp assembly. NOTE At this point, the two turn signal pin terminals must be removed from the two-place connector in order to remove the turn signal and directional stand-off from the fender support. The pin terminals will be re-installed to the connector after routing wiring through new directional stand-off and installing stand-off and turn signal to fender support. Follow the instructions under AMP MULTILOCK CONNECTORS in the applicable Service Manual to remove the pin terminals from the two-place con- nector. 10. See Figure 3. Obtain new directional stand-off and cap- screw from kit. Route wiring from turn signal lamp (9) through new directional lamp support (10) and elongated fender support hole (11). Install capscrew (6) through fender support, new directional lamp support then into turn signal. Tighten capscrew securely. 1 3 2 is 01494 1.4-place tail/stop lamp connector 2. Left turn signal 2-place multi-lock connector 3. Right turn signal 2-place multi-lock connector Figure 2. Disconnect Tail Lamp and turn Signal Connectors 11. Perform step 10 for the right side

Incoming search terms: