how to install saddlebag guards on softail deluxe

You search Auto repair manual PDF how to install saddlebag guards on softail deluxe, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install saddlebag guards on softail deluxe Direct Download speed 5282 Kb/s

  how to install saddlebag guards on softail deluxe Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL REAR SADDLEBAG GUARDS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION 1. Remove saddlebag, if equipped, from motorcycle. 2. Remove passenger footpeg or passenger footboard assembly (including footboard mount) from vehicle. 3. See Figure 1. Remove nut (1), seat strap bracket (if equipped) and 3/8 inch diameter bolt (2) from indicated position on rear fender support (immediately to the rear of the front seat) Discard the bolt, but save the nut for reinstallation. This location is where the upper part of the saddlebag guard will mount. 2 1 is03883 1. Rear fender support nut 2. Rear fender support screw Figure 1. Hardware Removal 4. See Figure 2. Install saddlebag guard (4) top flange (5) against fender support (3). Install 3/8-16 x 1-3/4 inch button head bolt with the seat strap bracket (if equipped) and hardware removed in Step 3 (if equipped) and nut in same direction as bolt removed in Step 3. Finger tighten only. 5. Position bottom flange (6) of saddlebag guard (4) against inboard surface of motorcycle frame (7) at location where passenger footpeg (2) (or passenger footboard bolt) attaches. If Heritage-Style Saddlebag relocation kit, Part Number 90238-00 is to be installed, the bracket should be positioned between the saddlebag guard flange and the motorcycle frame member. Follow installation instructions included with that kit. 6. See Figure 3. Determine your model application and follow the applicable installation procedure below: On models with passenger footpeg, but without saddlebag relocation bracket: Install 3/8-16 x 2-3/4 inch socket head cap screw (6) (For 2007 FLSTC Models, use the 3.5 inch long socket head cap screw (7) from kit) through footpeg support (B). Install support to frame. Tighten support bolt to 35-45 ft-lbs (47-61 Nm). Install lower saddlebag guard flange over bolt protruding from inboard surface of frame member. Install 3/8-16 lock nut to end of bolt. Tighten to 35-45 ft-lbs (47-61 Nm). Install footpeg (C) according to Service Manual instructions. On models with passenger footpeg and saddlebag relocation bracket: Install 3/8-16 x 2-3/4 inch socket head cap screw (6) (For 2007 FLSTC Models, use the 3.5 inch long socket head cap screw (7) from kit) through footpeg support. Install support to frame. Tighten support bolt to 35-45 ft-lbs (47-61 Nm). Position saddlebag relocation

Incoming search terms:

HARLEY DAVIDSON FLSTN SADDLEBAG GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
REMOVAL All Models 1. If equipped with saddlebags, removal may ease installation. Follow the instructions in the appropriate Service Manual or Instruction Sheet. 2. See Figure 1. Remove and discard the forwardmost fender support bolt (1). Repeat for the other side. 3. See Figure 2. On the left side, remove the footrest support mounting bolt (1) and footrest support bracket assembly (2). Discard the mounting bolt. 2005 – 2006 Models 1. Loosen the exhaust shields as necessary following the instructions in the appropriate Service Manual. Move as necessary for access. 2. Loosen the exhaust header nuts following the instructions in the appropriate Service Manual. 3. See Figure 3. Remove bolt (1) connecting the exhaust system (2) to the support bracket (3). 4. See Figure 4. Remove the two rear muffler bracket bolts (1). 5. See Figure 5. Move mufflers enough to access the rear bolt attaching the exhaust mounting bracket to the frame. Remove bolt (1) and discard. 2007 – Later Models NOTE On 2007 – later models, the frame tab (4) has a plug instead of a bolt (see Figure 6, item 1). 1. Remove plug and discard. 1 is05313 1. Fender support bolt (discard) Figure 1. Remove Docking Hardware 1 2 is05320 1. Footrest support mounting bolt 2. Footrest support bracket assembly Figure 2. Footrest Support Bracket Assembl NSTALLATION Right Side See Figure 5 or Figure 6. 1. See Figure 7. Install upper screw (7) in the fender support. Tighten screw finger-tight. 2. Install the lower screw (4 or 5) with the saddlebag guard, washer (9) and locknut (6) inside the frame. Tighten screw finger-tight. 3. Tighten the upper screw to 30 ft-lbs (41 Nm) . 4. Tighten the lower screw to 40 ft-lbs (54 Nm) . Tighten nut to 30 ft-lbs (41 Nm) . 5. 2005 – 2006 Models: a. Loosely install the exhaust header bolts. b. See Figure 4. Loosely install two rear muffler bracket bolts (1). c. See Figure 3. Loosely install bolt securing exhaust system (2) to support bracket (3). d. Tighten exhaust header bolts following the instructions in the appropriate Service Manual. e. Tighten support bracket bolt and rear muffler bracket bolts following the instructions in the appropriate Service Manual. f. Tighten exhaust shields following the instructions in the appropriate Service Manual. 6. Install saddlebag (if removed) following the instructions in the appropriate Service Manual or Instruction Sheet. 1 2 3 4 is05333 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Exhaust support bracket Figure 5. Install Saddlebag Guard – Right Side Shown (2005 Models) -J04645 2 of 4
2 1 3 4 is05332 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Frame tab Figure 6. Install Saddlebag Guard – Right Side Shown (2007-Later Models) Left Side 1. Loosely install upper screw (7) through the saddlebag guard and the fender support. NOTE Spacer (8) must be installed with the chamfer facing out. 2. See Figure 7. For 2005-2006 Models: Install lower screw (3) through the saddlebag guard, saddlebag guard spacer (8), footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . For 2007 and later Models: Install lower screw (10) through the saddlebag guard, footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . 3. Tighten upper screw to 30 ft-lbs (41 Nm)

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

HARLEY DAVIDSON NOSTALGIC SADDLEBAG GUARD RAILS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL 1. If desired, remove the saddlebags. 2. Remove screws (C) and locknuts (D). Save for installation. 3. Remove reflectors with fishing line or dental floss. Use a sawing motion to remove the adhesive. Clean the surface thoroughly with an equal mixture of isopropyl alcohol and distilled water. Allow the surface to dry thoroughly. INSTALLATION 1. See Figure 1. Position the correct saddlebag guard rail (1 or 2) over the saddlebag guard and support assembly (A). Loosely install the screw (C) through the saddlebag-to- fender support bracket (B), through the saddlebag support (A) and through the inner hole of the saddlebag guard rail bracket. Install nut (D). Tighten finger-tight. NOTE Position the saddlebag guard rail as low as possible on the stock saddlebag guard and support assembly. 2. Install screws (6) and washers (5) through the clamp end of the saddlebag guard rail. Position clamp end around the upright of the saddlebag guard and install the clamp (3 or 4). Tighten screws finger-tight. 3. Align the saddlebag guard rail (1 or 2) parallel to the bottom of the saddlebag and muffler. Tighten the cap screw (C) and locknut (D) to 15-20 ft-lb (20-27 Nm) . 4. Tighten the clamp screws (6) to 22 in-lb (2.5 Nm) . NOTE The reflectors are location-specific. There are markings on the back of the reflector – “L BOTTOM” or “R BOTTOM”. 5. Peel the backing from the base of the new reflector (7 or 8). Without touching the reflector to the saddlebag guard, position the reflector and press the reflector to the saddlebag guard above the clamp (3 or 4) and press for 30 seconds. After releasing pressure, avoid direct contact with the reflector for at least 20 minutes. 6. Repeat all steps for the other side of the motorcycle. NOTE For ease of use, move the saddlebag buckles to the highest hole on the strap. 7. Install the saddlebags, if removed

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DETACHABLE SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
Detachable Saddlebag Configurations Table 1 provides a short description of the detachable saddlebag configurations. Table 1. Softail Detachable Saddlebag Configurations Accessory Configuration (Long Description) Short Descrip- tion Kit 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Other Detachable Accessories FL Outer 88237-07 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) Without Other Detachable Accessories FL Inner 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Rigid-Mounted Accessories FL Rigid 2006-Later FX Models (Except FXSTD) With Other Detachable Accessories FX Outer 88238-07 2006-Later FX Models (Except FXSTD) Without Other Detachable Accessories FX Inner 2006-Later FX Models (Except FXSTD) With Rigid-Mounted Accessories FX Rigid 2007-Later FXSTC Models With Stock Passenger Upright FXSTC Stock NOTE Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Install Turn Signal Relocation Kit Refer to instructions included with Turn Signal Relocation Kit 69857-07. Install Docking Hardware Kit(s) Without Other Detachable Accessories: Refer to instructions included with Docking Hardware Kit 53932-03. With Other Detachable Accessories: Refer to instructions included with Docking Hardware Kits 53932-03 and 88256-07. Install Rear Docking Adapter NOTE This procedure only applies to models without detachable accessories. 1. See Figure 1. Insert rear docking adapter (1) into holes in saddlebag bracket and hold in place. 2. Install rear docking adapter using screw (2) and nut (3). Tighten snugly.

Incoming search terms:

HARLEY DAVIDSON AIR WING SADDLEBAG LID RAIL LIGHTS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
INSTALLATION 1. If saddlebag rails have not yet been installed: Perform the Air Wing Saddlebag Rail installation up to the point of final assembly of the rails to the saddlebag lids. If saddlebag rails are already installed: Open one saddlebag and remove all loose contents. Remove one saddlebag from the vehicle per service manual instructions. From the underside of the saddlebag lid, remove the fasteners retaining the saddlebag rail to the lid. Note fastener position and save all components for installation. 2. ALL installations: See Figure 3. Obtain a saddlebag rail light assembly (1) from the kit. 3. Insert the light wires through the hole (B) in the side of the saddlebag rail (A) mounting post, and out through the bottom of the post. 4. Install the light to the underside of the saddlebag rail rear cross bar with two screws (4) from the kit. Tighten the screws >securely. 5. Insert the light wires through the left rear saddlebag rail mounting pad (C) and the left rear hole (H) in the saddlebag lid (G). Assemble the saddlebag rail to the lid per the instructions in the Air Wing Saddlebag Rail Kit, feeding the wires through the left rear saddlebag rail nylon washer (D), plain washer (E) and the hex head hollow screw (F). Tighten the two Phillips head screws to 27-31 in-lbs (3.1- 3.5 Nm) . Tighten the hex head hollow screw to 30-50 in- lbs (3.4-5.6 Nm) .

Incoming search terms:

HARLEY DAVIDSON FLHRS SADDLEBAG LOCK SET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
INSTALLATION 1. Lay a clean pad or blanket on the work surface to protect the saddlebag leather surfaces. 2. Open the saddlebag lid. Remove the saddlebag from the motorcycle, leaving the lid open. See SADDLEBAG REMOVAL in the Service Manual. Lay the saddlebag flat on the pad or blanket with the inboard side facing up and the lid furthest from you. 3. See . Obtain the templates (10) from the kit. Lay the correct (left or right) template in the upper rear corner of the hard plastic inboard face of the saddlebag. Fit the template around the rear of the lid hinge and against the curve of the raised surface in the middle of the saddlebag, and tape it into place. is03044 Figure 1. Template Placement (Left Side Shown) 4. Drill four 3/16 (0.19)-inch holes in the saddlebag inboard face where indicated on the template. 5. Drill four 5/32 (0.15)-inch holes in the saddlebag inboard face as indicated on the template. 6. Remove the template. Cut out the area in between the four smaller holes to create a rectangular opening for the lock arm. Stand the saddlebag upright, with the cover open. 7. See the Figure 2. Obtain one lockset (1) and two screws (5) from the kit. Position the lockset to the saddlebag as shown, with the actuator rod protruding through the rectangular opening cut in step 6. Insert the screws through the lockset mounting holes and into the saddlebag. 8. Position a backing plate (3) over the screw threads inside the saddlebag. Fasten the lockset and backing plate to the saddlebag with two lockwashers (6) and hex nuts (7) from the kit. 9. Using a 3/16-in. hex wrench, remove the two screws holding the inside cover over the existing pushbutton lid release. Remove the cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) NOTE Make sure you are using the correct retaining-ring pliers. Verify that tips of pliers are not excessively worn or damaged. 10. Remove the retaining ring fastening the lid release cable to the pushbutton. Unhook the cable from the pushbutton lever, and pull the cable sheath out of the retaining channel on the inboard wall of the saddlebag. Remove the flat washer from the cable end. Do not discard the retaining ring and washer. 11. Trim about one inch (25 mm) from the rearmost part of the retaining channel, and re-insert the cable into the channel so the free end is at the rear of the saddlebag. 12. Insert the cable end through the hole in the backing plate, and slip the washer over the end of the cable fitting. Insert the cable into the slot in the lockset actuator rod so the ball on the end of the cable fits into the depression.

Incoming search terms:

HARLEY DAVIDSON SPORTSTER LEATHER SADDLEBAG KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
SADDLEBAG INSTALLATION 1. See Figure 3. Remove the rear shock absorber bolt (Figure 1, Item 1). Position the 0.531 x 0.75 x 0.25 inch spacer (7) and the front saddlebag bracket attachment hole over the rear shock absorber bolt location. Secure with the 1/2- 13 x 3.75 inch screw (5). 2. See Figure 3. Position the 0.325 x 0.75 x 0.25 inch spacer (8) and the rear saddlebag attachment hole over the second hole on the rear of the fender, fender support cover, and relocation pad. From the underside of the fender, insert a 5/16-18 x 3.00 inch screw (6) and secure with locknut (10). Tighten locknut (10) to 24-27 ft-lbs (32.5-36.6 Nm) . 3. Tighten the front screw (5) to 21-27 ft-lbs (28.5-36.6 Nm) . 4. See Figure 3. Assemble an isolator washer (12) onto an isolator bushing (13). Place a screw (15) through the bushing. 5. Place the screw and bushing assembly into the top hole inside the saddlebag back. 6. See Figure 3. Push a saddlebag isolator (14) over bushing with cone shape toward saddlebag. 7. Place saddlebag in position on bracket and insert the new screw (15) into the bracket. Do not tighten. 8. Repeat steps 4 through 7 for remaining holes. With all isolators in place, tighten screws to 96-120 in-lbs (10.8- 13.6 Nm) . 9. Repeat Steps 1 through 8 for the opposite saddlebag. 10. Raise rear wheel until the rear shock absorbers align with shock absorber mounting holes on the swingarm. Support the wheel to prevent it from falling during the following step. 11. See Figure 1. Attach rear shock absorber to swingarm by installing bolt (1), washer (2) and nut (4). Tighten bolt to 45-50 ft-lbs (61.1-67.9 Nm) . Repeat step on opposite side of motorcycle. INSTALL REFLECTORS Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b) 1. See Figure 3. Measure approximately 1-1/2 in. (38 mm) from the bottom edge of the saddlebag. Orient the reflector horizontally and carefully center the reflector mount between the straps of bags with straps or locate it at the rearward portion of bags without straps. Mark hole location. 2. Using appropriate tool, make two 3/16 in. holes in sad- dlebag. 3. Install reflector mount (3) on saddlebag using two pushnuts (2). 4. Remove adhesive backing from reflector (4) and install on mount. 5. Repeat steps 1 through 4 for the opposite saddlebag. INSTALL SEAT After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1. See Service Manual instruction to install the seat

HARLEY DAVIDSON SADDLEBAG GUARD RAIL KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation NOTE A Service Manual for your vehicle is available from your Harley-Davidson Dealer. 1. Remove saddlebags from motorcycle according to Service Manual instructions. 2. Remove left and right side covers (located just ahead of saddlebags) by removing Phillips head screw from bottom of side cover. Save hardware and side covers for later reassembly. 3. Remove upper and lower bolts securing left and right forward saddlebag guards to frame. Remove Phillips head screws securing saddlebag guards to muffler supports. Discard saddlebag guards, but save hardware. 4. See Figure 1. Install new left and right forward saddlebag guards (1) with upper bolts (2), lower bolts (3) and Phillips head screw (4) saved from Step 3. 5. Insert one rear guard rail mount (6) onto rounded, tubular end of one of the saddlebag side guard rails (5). 6. Insert a hex cap screw (8) through one of the front guard rail mounts (7) as shown. 7. Line up saddlebag side guard rail (5) with attached rear guard rail mount (6) from Step 5 with lower hole in forward saddlebag guard rail (1). Insert hex cap screw (8) from front guard rail mount (7) through hole in forward guard rail (1) and into side guard rail assembly. Tighten finger tight. 8. See Figure 2. Install a side guard rail (2) in lower position on rear fender support (3) with pan head screw (1). Tighten finger tight. 9. Repeat Steps 5 through 8 in upper position. 10. Repeat Steps 5 through 9 for opposite side of vehicle. NOTE Each of the four guard rail clamps vary slightly. Two fit together for the right side of the motorcycle and two fit together for the left side. The inner right and left clamps have two holes drilled through them. 11. See Figure 2. Locate four guard rail clamps (4). Match up two left side and two right side guard rail clamps. Install one piece of cushion tape to the lower inner surface of right and left inner clamps. Peel off paper from outer surface of tape. Do not apply tape to the outside clamps. NOTE Be sure that you correctly position the inner clamps on the side guard rails, as directed in Step 12, before tape on inner clamp contacts side guard rails. Tape is very sticky and will be difficult or impossible to remove once it has made contact with side guard rail surface. 12. See Figure 2. Position clamps (4) in desired position on side guard rails (2). Install clamps (4) on left and right side of vehicle side guard rails using four Torx screws (5). Torx screw heads should face inward toward motorcycle. Tighten each screw a little at a time until secure. 13. Tighten hex cap screws and pan head screws installed in Steps 7 and 8.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SADDLEBAG KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a) NOTES Maximum saddlebag weight capacity is 7 lbs (3.18 kg) for each bag. Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. 2000-2002 Models with Wide Tire Kit 1. See Figure 1. Remove and discard stock screws (1) and washers (2) from fender support. Button head screws from wide tire kit must be installed with button heads on inside of fender. Fastener contact with tire can lead to premature tire failure, which could result in death or serious injury. (00417b) 2. See Table 3. Determine appropriate screw from wide tire kit. 3. See Figure 2. Install saddlebag using screw (from wide tire kit) (1), washer (2) and nut (3). The screws are installed from inside to outside of fender. NOTE If you do not have the appropriate screw from the wide tire kit, it can be purchased from a Harley-Davidson dealer. Table 3. Wide Tire Kit Screws (3/8-16) Wide Tire Kit 44490-00, Hardware Kit 43763-00 Wide Tire Kit 44490-00, Hardware Kit 43761-00 Part Number and Length X X 4030 – 2-1/2 inch X X 4225 – 3-1/2 inch X X 4224 – 1-1/2 inch X X 4044 – 1-1/4 inch X 4215 – 2 inch X 3912 – 2-3/4 inch X X 4228 – 2-1/4 inch X X 4229 – 3-1/4 inch Failure to tighten saddlebag mounting bolts to specified torque could result in damage to saddlebags. (00406c) 4. Tighten all saddlebag hardware to 22 ft-lbs (30 Nm). NOTE Check that front screws have at least one thread exposed beyond the nut after proper torque has been applied. 5. Install reflectors on saddlebag. Refer to Install Reflectors subtopic.

Incoming search terms:

Incoming search terms: