how to lower my 1970 flh

You search Auto repair manual PDF how to lower my 1970 flh, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to lower my 1970 flh Direct Download speed 5282 Kb/s

  how to lower my 1970 flh Full Version speed 6162 Kb/s



HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

HARLEY DAVIDSON VENTED FAIRING LOWERS KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1. See Figure 1. From the kit, obtain the left side fairing lower (1), left side fairing lower cap (2), two flange locking nuts (3) and two stud clips (4). Place fairing lower cap in front of the left side engine guard and left side fairing lower behind engine fairing guard. With both pieces in place around engine guard, install the two flange locking nuts onto the studs clips and hand tighten. Repeat procedure for right side fairing lower. 2. Secure bottom of fairing lower to lower engine guard with round clamp (5) from hardware kit. Position clamp around engine guard with tabs toward rear of vehicle and flat side of clamp against fairing lower and with the rubber washer (6) between clamp and engine guard. Place Torx pan screw (7) through fairing lower, rubber washer and clamp. Secure assembly with flanged locknut (8). Repeat for right side fairing lower. Tighten to 144 in-lbs (16.3 Nm). 3. Tighten all left and right side upper flange locking nuts (3) to 72 in-lbs (8.1 Nm). 4. Install left side door assembly glovebox (9) to fairing lower using the attachment cord (10). Insert glovebox door into fairing lower. Repeat for right side fairing lower. NOTE Do not press reflector firmly into place until you have it positioned in desired location. The adhesive is very strong and once it comes in contact with a surface, it will be difficult to remove without damaging the reflector. 5. Peel adhesive strip off back of reflector from kit. Position reflector on side of front fender above chrome side trim strip and approximately 4 inches rearward from front of fender. Press reflector securely into place. Repeat for opposite side reflector

Incoming search terms:

HARLEY DAVIDSON CHROME LOWER BELT GUARD INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the Maxi® Fuse. 2. See Figure 1. Remove the three screws with captive washers (3) securing the original equipment (O.E.) lower belt guard (debris deflector, Item 1) to the underside of the rear fork (2), and set them aside for re-use. Remove and discard the lower belt guard. 3. Position the new chrome lower belt guard in place on the underside of the rear fork, lining up the three holes in the belt guard with the mounting holes in the fork. Insert the three screws saved earlier through the holes in the belt guard, and thread them into the fork. Tighten the screws to 36-60 in-lbs (4.1-6.8 Nm) . 4. Verify that the Ignition/Light Key Switch is turned to the OFF position. Refer to the Owner’s Manual and follow the instructions given to re-install the Maxi® Fuse. 2 1 3 is04766 1. Lower belt guard (debris deflector) 2. Rear fork (swingarm) 3. Screw with washer (3) Figure 1. Lower Belt Guard Installation

HARLEY DAVIDSON FXSTD DETACHABLE WINDSHIELD AND DOCKING HARDWARE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
INSTALLATION NOTE Use the Docking Hardware Kit to assemble two upper and two lower clamps. See the Service Parts illustration. The upper clamps use a mounting pin (4) and the lower clamps use a button head screw (5) to fasten the windshield mounting bushing. 1. Assemble the windshield docking hardware as follows: a. Install a larger chrome washer (6) and bushing (7) onto a button head screw (5). Thread the screw into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. b. Install a larger chrome washer (6) and bushing (7) onto a mounting pin (4). Thread the pin into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. 2 1 3 4 4 5 is 02187 1. Upper clamp 2. Lower clamp 3. Fork tubes 4.1/8 inch (3 mm) approximately 5.3.0 inch (76 mm) Figure 1. Installing Clamps NOTE Place shop rags on the headlamp, front fender and front of the fuel tank to prevent scratches to these components. Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts. 2. See Figure 1. Install a lower clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the top of the lower triple clamp, then finger tighten the lock nut. Repeat with the second lower clamp and fork tube. NOTE Keep front wheel straight to prevent brackets from scratching fuel tanks. See Figure 1. Install the clamps on the fork tubes so the bushing center lines are 3 inches (76 mm) apart. 3. Install an upper clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the bottom of the upper triple clamp. Ensure that the center lines of the upper and lower bushings are 3 inches (76 mm) apart, then finger tighten the lock nut. Repeat with the second upper clamp and fork tube

2007 KTM SX-F 250- 450 Kickstand Installation and Removal Manual Instructions

0

Filed Under (KTM) by admin on 26-01-2012

download
Remove the lower d bolt making sure you keep track of the order of the small parts for re-assembly. 2) Remove the lower in-frame bolt. 3) Install the supplied lower kickstand mounting bracket onto the frame at the lower chain roller boss. The counter bore should slide over and onto the frame boss. The chain roller should go back into place just how it came e supplied lower kickstand mounting bracket between it and the frame. Do not is bracket needs to pivot to align with the lower hole in the main . 4) Install the kickstand onto the bike using one of the provided M8x30mm flat head sub-frame to main-frame bolt location. Do not tighten yet. 5) Line up and install the other provided ad bolt thru the lower kickstand mounting hole into the supplied lower kickstand mounting bracket. 6) Now tighten all three bolts, two mounting bolts (front) and one lower kickstand mounting bracket 7) Periodically check the kickstand and all mounting bolts for tightness. Maintenance: Clean and lubricate the kickstand pivot area after each ride! We recommend using a heavy-duty chain lube. If necessary, you can remove the back cover plate for additional cleaning. Never remove the kickstand leg pivot bolt!

Incoming search terms:

HARLEY DAVIDSON FLSTS MUD FLAP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
Installation For installation on rear fender with marker light: 1. Cut out Rear Fender Template. 2. Use a paper punch to punch out holes marked A and C . Holes A are the locations of the marker light screws, and hole C is the location of the marker light wiring. Cut along centerline of template from top down to hole C . 3. Remove light lens by carefully pressing down on top center of light to disengage tab. 4. Remove the two screws, washers, and nuts that hold the marker light assembly in place and carefully pull the light assembly away from the fender. Disconnect the wire connector and remove the light assembly. 5. Slip template over marker light wires, align holes marked A with marker light holes, and align lower edge of template with lower edge of fender. Tape template in place. 6. Prick punch holes marked B at indicated centers on template. 7. Carefully, and as accurately as possible, drill holes marked B in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 8. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure outer holes with buttonhead screws (3), washers (6), and locknuts (7) contained in kit. The mud flap is split to fit around light assembly wires. 9. Using the longer panhead screws provided in the kit, install fender tip light and check that light is operational. For installation on rear fender without marker light: 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Rear Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes marked B and C at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked B and C in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit. For installation on front fender (FLSTS only): 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Front Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit

Incoming search terms:

Yamaha Road Star EZ-Steer Installation Manual

0

Filed Under (Yamaha) by admin on 17-02-2011

download
Champion Yamaha Road Star EZ-Steer Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamp of your Yamaha Road Star Motorcycle. Much of the OEM hardware is retained and reused. It is assumed that the installer has advanced and/or professional skills in motorcycle servicing. We recommend that you use an OEM service manual and follow the prescribed disassembly, installation and torque specifications for the upper and lower clamp assembly. Recommended Procedures • Remove headlight, windscreen (if so equipped) and brackets from motorcycle. • The wheel and fork assembly can be removed as one complete unit. Disconnect the master cylinder brake line from the tee fitting below the lower triple clamp. The caliper brake lines may be left in place on the tee fitting. • Install supplied extensions to fork tubes the supplied o-rings. Apply lubricant to o-rings and extensions prior to installing to fork tubes. • Install the lower fork tube covers to the lower clamp prior to installation to motorcycle using the longer screws supplied. The two longest screws are used in the outboard holes. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 30 lb. ft. • Slide fork tubes up through bottom of lower clamp approximately 6-8 inches. Install the OEM gaskets, washers and upper fork tube covers. Do not reinstall brake line holders at this time. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of extension is flush with top surface of clamp. • Torque dome nut to 85 lb. ft. • Ensure that fork tube extensions are flush with top of upper clamp. Torque upper and lower clamp bolts to 35lb. ft. • Install handle bars to upper clamp using OEM bolt with supplied flat washers. One washer on top, two on bottom, both sides. • Reinstall brake line holders to the bottom of the lower triple clamp using the supplied M6 NyLoc nuts. • Reinstall all other OEM parts as removed. • Bleed brakes. EZ-Steer Maintenance

Incoming search terms:

Harley Davidson FLH EZ-Steer Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2012

download
Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamp of your Harley Davidson FLH Motorcycle. We recommend that you use an OEM service manual and follow the prescribed disassembly, installation and torque specifications for the upper and lower clamp assembly. Before Installing Kit (2008 & Prior) The wiring bracket of the OEM upper triple clamp needs to be modified to fit the Champion upper triple clamp. After removing / disassembling the OEM parts from your motorcycle, position the OEM wiring bracket onto the Champion upper clamp as shown. Scribe the ID of the steering stem hole onto the wiring bracket and enlarge the hole to scribe line. This will allow the wiring bracket to fit over the new Stem Lock-Nut. Install OEM handle bar mount assemblies to Champion upper clamp using Item #5 (Handle Bar Mount Spacer). The spacers are used on top of the upper clamp. Installation Notes • Be sure to use the correct fork extension. Yellow 2002 and newer (non adjustable air pressure). Black for 2001 and older (adjustable air pressure). Be sure to double check the fork cap (Fork Tube Plug) being removed. • Reinstall the OEM O-rings on Item #7 (Fork Extensions) prior to installing in the fork tubes. • On some of the Road King models with chrome headlight Nacelle, Item #9 must be mounted underneath upper clamp Item #2 to ensure enough room for air fittings. • Be sure to replace fork covers in proper order, during installation of the fork tubes. • Thoroughly clean sides of steering neck and install self adhering rubber stops where steering stop screws contact frame. • Secure wires and cables clear of steering stop bolts. • Do not torque Item # 1 (½-20 x 1-1/4″ Hex Head Bolt) until fork tubes have been installed to assembly. • Note the torque specification for the items listed in the table below.

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

HARLEY DAVIDSON SOFTAIL CHROME LOWER BELT GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVING STOCK PLASTIC LOWER BELT GUARD 1. See Figure 1. Remove the hex head bolt (2), washer (3), acorn nut (5), hex head screw (4) and acorn bolt (8) attaching plastic belt guard to rear fork. 2. Remove the plastic belt guard. Save fasteners (2), and (4), washer (3), acorn nut (5) and acorn bolt (8) for installing new chrome belt guard. INSTALLING CHROME LOWER BELT GUARD 1. See Figure 2. Position the new chrome belt guard from kit over belt. Align the holes in guard with mounting lugs on rear fork. Install acorn bolt (9) through mounting lug and fasten to belt guard. Finger tighten only. 2. Install screw (4) with washer (5, from kit) through belt guard and fasten to threaded mounting lug. Position the guard for adequate clearance and finger tighten screw. 3. At the upper belt guard, install the original forward hex bolt (2) and original washer (3) through the upper guard (1), then through the upper hole in chrome belt guard and through mounting lug on rear fork. Secure with original acorn nut. 4. Tighten all hardware to 110 in-lbs (12.4 Nm)

Incoming search terms: