how to remove a dent from a motorcycle fender

You search Auto repair manual PDF how to remove a dent from a motorcycle fender, if there are search results will appear below. If search results do not exist, please search by others keyword.





GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

HARLEY DAVIDSON FRONT AND REAR FENDER TIP TRIM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation GENERAL The original equipment (stock) fender tip lamp assemblies must be removed and the wire(s) must be unplugged or removed as specified in the following instructions. FRONT FENDER TIP REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1994 AND LATER FLT MODELS 1. Refer to the applicable FLT Service Manual. Remove headlamp assembly with housing. 2. Locate the 3-place connector [32 in wiring diagram] through which 12vdc and electrical ground are connected to the fender tip lamp assembly. The connector locations are as follows: FLTC Ultra: Under fuse and circuit breaker block FLHT/C/C-U: On bottom of left outer fairing bracket FLHR: On left front above air suspension valve NOTE Before disassembling the connector in the next step, refer to the applicable wiring diagram and check wire colors and connections to assure that connector [32] has been located. 3. Refer to the “DEUTSCH ELECTRICAL CONNECTOR” section in the FLT Service Manual and remove the leads, connected to the fender tip lamp, from the socket half, connector [32B]. 4. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 5. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wires connected to lamp assembly. 6. Reach under left side of fender and gently pull wires through rear hole in left side of fender and then through clips on left side of fender and finally through front hole and out of trim strip. REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1993 AND EARLIER FLT MODELS, FLSTC AND FLSTN 1. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 2. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wire connected to lamp assembly. 3. Unplug wire connector located about 3 in. from lamp assembly. Cover the socket half of connector (connected to motorcycle wiring) with electrical tape. INSTALLING FRONT FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in fender and guide outer ends of fender tip trim into trim strips on sides of fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs . REAR FENDER TIP REMOVAL OF STOCK REAR FENDER TIP LAMP ON ALL MODELS Follow steps 1 through 3 given above for “1993 AND EARLIER FLT MODELS, FLSTC & FLSTN” INSTALLING REAR FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in rear fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

Incoming search terms:

HARLEY DAVIDSON HERITAGE CHROME FRONT FENDER RAIL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION NOTE See Figure 1. Be careful not to crack plastic fender lamp lens (2) or chrome plate when removing lens. 1. Remove fender lamp light lens (2) by placing screwdriver in slot in top of lens and carefully prying cover loose. Retain lens and gasket for later installation. 2. Loosen four hex socket head screws (1) which attach fender (4) to fender mount. 3 2 4 1 is03805 1. Fender mount screws (4) 2. Fender lamp light lens 3. Fender Rail 4. Fender Figure 1. Installed Front fender Rail NOTE When installing fender rail (3), be sure fender rail supports are inside of fender. 3. Place fender rail (3) from kit into position, aligning the front bracket hole of rail with hole in front of fender (4). Fender rail supports will fit snugly inside fender. NOTE Be careful not to damage the fender lamp wire when securing front fender rail into place. 4. Use a magnet to place a 10-32 x 1/2 inch phillips screw through the hole in front fender and through front bracket hole of fender rail (3). 5. Loosely secure fender rail (3) to fender (4) with 1/2 inch flat washer and hex locknut. 6. On right side only, remove two hex socket head screws and nuts. Retain nuts for installation. 7. Replace original two socket head screws with 5/16-18 x 2 inch screws from kit. 8. For vehicles without caliper/rotor covers: On left side of fender (4) only, install a washer between rail (3) and fender for both screws. Replace original two hex socket head screws with 5/16-18 x 2 inch screws from kit. For vehicle with caliper/rotor covers: Do not replace hex socket head screw that supports caliper/rotor cover. On left side of fender (4), install a washer between fender (4) and rail (3) on screw that does not support the caliper/rotor cover (towards the front of the vehicle). Replace remaining hex socket head screw with 5/16-18 x 2 inch screw from kit. 9. Install four original nuts. 10. Tighten front bracket Phillips screw securely. Tighten four hex socket head screws to 14-18 ft-lbs (19-24 Nm). 11. Install gasket and fender lamp lens removed earlier

Incoming search terms:

HARLEY DAVIDSON HERITAGE REAR FENDER RAIL DISASSEMBLY AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
DISASSEMBLY NOTE See Figure 1. Saddlebags must be removed to insert spacer (1). 1. Using a small flat head screw driver, remove rear fender tip light lens cover (A) by gently prying cover away from assembly. (There is a notch at top of cover to ease removal.) Remove and retain cover (A) and gasket (C). 2. Remove fender tip light assembly (B) by removing two screws, four star washers, and two nuts (not shown) using a #2 Phillips screw driver and a 3/8 inch wrench. Retain all hardware for reassembly. 3. Remove hole plugs from rearmost fender strut holes on both sides of fender. 4. Mark fender on both sides of bike using rear most fender strut hole as a template. Do not contact tire with drill bit when drilling fender holes. Drill bit contact with tire can lead to premature tire failure, which could result in death or serious injury. (00403f) 5. Carefully remove fender strut and drill a 11/32 inch hole through each side of fender in locations marked in Step 4. 6. Loosely reinstall fender strut (D), allowing enough room to slip spacer (1) between fender (E) and strut. INSTALLATION 1. Align rear fender rail (2) from kit with rearmost fender strut (D) mounting holes, making sure lower mounting tab (3) is inside fender (E). Place large chrome washer (4) from kit next to head of button head socket bolts (5) from kit. Insert bolt through fender rail (2), fender strut (D), spacer (1) and fender (E), in that order. Install large unfinished washer (6) from kit onto end of bolt (5). Secure assembly into place by threading locknuts (7) from kit onto ends of bolts (5) from inside of fender (E). Tighten loosely at this time. 2. Install truss head screw (8) from kit through fender (E) and rear fender rail mounting tab (3). Secure into place using small washer (9) and locknut (10) from kit. Use #2 Phillips screwdriver and a 3/8 inch wrench to tighten rear mounting assembly securely. 3. Tighten fender strut bolts (5) to 21-27 ft-lbs.(28-37 Nm) 4. Reinstall fender tip light assembly (B), gasket (C) and lens (A) using original hardware (not shown)

Incoming search terms:

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

Incoming search terms:

2002-2004 TRIUMPH BONNEVILLE AMERICA/ SPEEDMASTER CARBURETOR KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-10-2010

download
A.) REAR WHEEL REMOVAL- PAGE 14-16 Triumph Motorcycle Service Manual 1.) Support motorcycle on center stand or center lift so rear wheel is suspended and there is clearance for removal. Use tie downs. 2.) If both wheels are raised chock the front wheel to prevent any weight shift when rear wheel is removed. 3.) Remove chain guard. 4.) Remove caliper and support so there is no strain on the brake line. 5.) Remove both silencers from exhaust headers. 6.) Remove axle nut and washer—support or chock rear wheel—and slide out axle. 7.) Disengage chain from sprocket and hang over swing—use soft cloth to protect swing arm from scratches that will occur if you do not cover. 8.) Lower wheel to the ground and collect spacer and caliper support arm and all fasteners for re-assembly. B.) REMOVE SEAT PAGE 15-9 Triumph Motorcycle Service Manual 1.) Remove the 12 mm bolt from rear seat section—if you have a pillion pad remove it first by removing the 8 mm bolt, slide forward and lift free of seat catch. Take a position where you can see what you are doing or you will scratch your painted surface. 2.) Lift seat from the rear and slide backwards to disengage tongue– collect all fasteners for re-assembly. C.) REMOVE REAR MUD GUARD PAGE 15-14 Triumph Motorcycle Service Manual 1.) Disconnect battery and remove from motorcycle. 2.) Disconnect electrical connectors on the underside of the mudguard. 3.) Support fender from beneath and remove the 4 side allen head mount bolts and 2 12mm hex head top front mount bolts– collect all fasteners for re-assembly. D.) REMOVE FUEL TANK PAGE 9-11 Triumph Motorcycle Service Manual 1.) Turn off fuel tap. 2.) Remove fuel line at the tap connection. 3.) Remove the 12mm rear tank-mounting bolt. 4.) With assistance from another set of hands support tank at the rear and lift so that the breather line is visible on the right side of the underside of tank—remove and plug line. 5.) With tank raised and supported at the rear slide backwards— disengaging it from the front mounting rubbers—set tank aside in a safe place to prevent any damage to the painted surface. E.) REMOVE SIDE COVERS PAGE 15-10 and 9-15 Triumph Motorcycle Service Manual 1.) Loosen and remove left side cover screws on the air filter facade— lift slightly to disengage top mounts and remove—set aside in a safe place to prevent damage to painted surface. 2.) On right side cover simply and gently pull bayonet fittings from rubber slip mounts. 3.) Secure these rubber mounts and remove for later re-assembly with the Bonneville Performance brackets.

Incoming search terms:

HARLEY DAVIDSON FLSTS MUD FLAP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
Installation For installation on rear fender with marker light: 1. Cut out Rear Fender Template. 2. Use a paper punch to punch out holes marked A and C . Holes A are the locations of the marker light screws, and hole C is the location of the marker light wiring. Cut along centerline of template from top down to hole C . 3. Remove light lens by carefully pressing down on top center of light to disengage tab. 4. Remove the two screws, washers, and nuts that hold the marker light assembly in place and carefully pull the light assembly away from the fender. Disconnect the wire connector and remove the light assembly. 5. Slip template over marker light wires, align holes marked A with marker light holes, and align lower edge of template with lower edge of fender. Tape template in place. 6. Prick punch holes marked B at indicated centers on template. 7. Carefully, and as accurately as possible, drill holes marked B in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 8. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure outer holes with buttonhead screws (3), washers (6), and locknuts (7) contained in kit. The mud flap is split to fit around light assembly wires. 9. Using the longer panhead screws provided in the kit, install fender tip light and check that light is operational. For installation on rear fender without marker light: 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Rear Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes marked B and C at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked B and C in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit. For installation on front fender (FLSTS only): 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Front Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit

Incoming search terms:

Incoming search terms: