how to remove antenna connector from tour pack

You search Auto repair manual PDF how to remove antenna connector from tour pack, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to remove antenna connector from tour pack Direct Download speed 5282 Kb/s

  how to remove antenna connector from tour pack Full Version speed 6162 Kb/s



GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

HARLEY DAVIDSON BOOM! AUDIO BASS BOOSTER TOUR-PAK PORT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
PREPARATION NOTE For vehicles equipped with security siren: • Verify that the Hands-Free Fob is present. • Turn the ignition key switch to IGNITION. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the owner’s manual and follow the instructions to remove the main fuse. INSTALLATION NOTE The Tour-Pak does not need to be removed from the vehicle to perform this installation. 1. Open the Tour-Pak lid and remove all items from the Tour- Pak base. 2. Models equipped with mat: Remove the mat. Models equipped with liner: Open the map pocket, and remove the acorn nuts with flat washers. Remove the map pocket and liner. 3. Remove four screws from the left-side speaker grille on the Tour-Pak. Remove the speaker grille from the speaker pod. 4. Remove the speaker from the speaker pod. Carefully pull the two socket terminals from the speaker spade contacts. 5. Remove the grommet, and draw the rear speaker/passenger controls connector out of the speaker pod. Separate the connector halves. 6. Repeat Steps 3 through 5 for the right-side speaker. 7. See Figure 1. Get the drill template (3) from the kit. If NOT equipped with power port: a. Remove one speaker pod mounting screw and flat washer. b. Align the drill template on the inside of the Tour-Pak with the speaker pod holes, and hold in place with the mounting screw and washer. c. Repeat for the remaining template mounting holes. If equipped with power port: a. Remove the two screws and flat washers to free the power port from the Tour-Pak. b. Align the drill template on the inside of the Tour-Pak with the power port holes, and hold in place with the mounting screws and washers. c. Repeat with the top speaker pod mounting screw and flat washer. NOTE Tighten the screws enough to hold the speaker pod in place as the pilot hole is drilled. 8. Where indicated on the template, drill a 3/16 inch (5 mm) diameter pilot hole through the Tour-Pak wall and speaker pod. 9. Remove the screws and speaker pod, and set aside. Turn the template over, and repeat Steps 7 and 8 on the left side of the Tour-Pak. NOTE Hole size will affect the fitment of the ports. The hole saw needs to be sharp. 10. Carefully drill a two inch (51 mm) diameter hole with a sharp hole saw, at the pilot location, through each speaker pod and in both locations on the Tour-Pak wall. 11. Temporarily install the Tour-Pak liner (if equipped), and mark the location of the two inch (51 mm) diameter holes on the outside of the liner. Remove the liner, and carefully cut the two holes in the liner front wall

Incoming search terms:

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

Incoming search terms:

HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

HARLEY DAVIDSON AM/FM ANTENNA RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Owner’s Manual and follow the instructions given to remove the left-side saddlebag. Gently pull the left-side cover from the frame downtubes (no tools are required), and remove the main fuse. 2. See Figure 1. Disconnect the antenna cable from the antenna base assembly (1). 3. Unscrew the antenna mast (2) from the antenna base, and set it aside for later installation. 4. Remove the lower locknut (3), and remove the antenna base from the mounting bracket (5). Save both locknuts, but discard the lockwasher (4). 5. Remove the two TORX® head screws (6) and lockwashers (7) retaining the antenna mounting bracket to the saddlebag rear support bracket (8). Discard the bracket and fasteners. 6. Carefully remove and discard any cable straps securing the antenna cable to the fender support and saddlebag rear support brackets. 8 9 6 3 2 5 7 4 3 1 is05436 1. Antenna base assembly 2. Antenna mast 3. Locknut (2) 4. Lockwasher 5. Original antenna mounting bracket 6. TORX head screw (2) 7. Split lockwasher (2) 8. Saddlebag rear support bracket 9. TORX Pan head screw and flanged locknut Figure 1. Original Antenna Mount 7. Remove and discard the TORX head screw and nut (9) that fastens the lower saddlebag support bar to the rear fender support bracket. 8. See Figure 2. Obtain the new antenna bracket (1), button head screw (2), flat washers (3 and 4) and flange nut (5) from the kit. NOTE If V-Logo Rear Fender Trim Rail Kit 91100-09 has been installed, the thick washer (4) is not used, and can be dis- carded.

HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-Pak®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

Incoming search terms:

HARLEY DAVIDSON FXD (Dyna Super Glide) TACHOMETER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
1995 Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1.1995 MODELS, REMOVAL OF ELECTRONIC SPEEDOMETER AND BRACKET 1a. Refer to applicable Service Manual procedure and remove seat. 1b. Refer to applicable Service Manual procedure and remove fuel tank. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 1c. Remove speedometer sensor cable from mounting clips under tank. See Figure 1. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Cut cable tie holding sensor wires to right rear frame tube. 1d. Refer to applicable Service Manual procedure and remove headlamp, for work clearance. 1e Remove handlebar clamp screws securing speedometer bracket. Remove speedometer, bracket, and harness. 2.1995 MODELS, DISCONNECT MAIN WIRING HARNESS 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 2a. Disconnect the battery, negative cable first. Refer to applicable Service Manual procedure and disconnect main wiring harness 8-place connector [21A, B], at the front of the motorcycle. 3.1995 MODELS, REMOVE SPEEDOMETER LEADS FROM 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 3a. See Figure 2 and Service Manual wiring schematic. Pull the following wires and terminals out of connector [21B]. Wire Color Cavity Number Orange/white 5 White/green 1 Black 2 3b. Remove the large female connector from the fuel gauge black wire. 3c. Slide the wires removed in step 2a out of the plastic conduit covering the wires connected to the 8-place connector. 1 WARNING 1 WARNING 1 WARNING Figure 1. Speedometer Sensor Connection [65] 4973 Speedometer sensor connector [65] Figure 2. Tachometer/Speedometer Wire Splices and Terminal Connections [21B, A] i00240-.tif Splices 4.1995 MODELS, REMOVE INDICATOR LAMPS FROM BRACKET 4a. Remove the screws that secure the indicator lamps assembly to the speedometer bracket. Retain screws and indicator lamps assembly for installation on speedometer/tachometer bracket later. 5.1995 MODELS, REMOVE SPEEDOMETER FROM BRACKET 5a. Unscrew boot from speedometer reset switch. Remove cover screws and rear cover. 5b. See Figure 3. Note position of rear speedometer gasket and remove it. Push on rear of speedometer while simultaneously pulling speedometer and front gasket from bracket. Do not remove front gasket from the speedometer. 6.1995 MODELS, INSTALL SPEEDOMETER IN KIT BRACKET 6a. See Figure 5. Place wires from speedometer through front of left opening in double bracket. Lubricate the front and rear gaskets with isopropyl alcohol or glass cleaner to ease installation. 6b. Insert speedometer into the front of the double bracket. Be sure wire guides are aligned with opening at bottom of bracket. 6c. Place rear gasket in position and align gasket tabs. Work gasket into space between speedometer and bracket by pushing speedometer against one side of bracket while pushing gasket into position at the opposite side. 6d. Add amber bulb assembly from kit to speedometer in order for tachometer and speedometer backlighting to match. 6e. Replace cover and boot from reset switch.

Incoming search terms:

HARLEY DAVIDSON KING TOUR-PAK WRAP AROUND LIGHT UNIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the negative battery cable (-) following the instructions in the owner’s manual. 2. Locate the two-sided template (part number 50002-01) printed on a 11 x 17 inch sheet of poster board. Cut out the template as indicated. 3. If the motorcycle is radio equipped, separate the antenna cable from terminal at antenna base. Remove the nut, lockwasher and ground ring terminal from antenna terminal. Remove phillips head screw threaded into antenna base. Remove mast and antenna base. Detach mast from antenna base by turning counterclockwise with adjustable wrench across flats. 4. See Figure 10. Shield threads of antenna terminal stud with strip of light cardboard. Remove terminal with pliers across cardboard strip. Save terminal and mast for later installation. 5. See Figure 1. Open Tour-Pak top and remove all loose contents. Remove Tour-Pak. Align the template as follows: a. Place center line template (4) along rear top edge of Tour-Pak (1) with curved end against one corner. b. Mark centerline at top edge of Tour-Pak. c. Reverse center line template and mark center with curved end against opposite corner. d. If centerlines overlap, mark center one half the distance between the two lines. e. Place a square against lip at top of Tour-Pak and draw a 3 in (76 mm) line down from the center mark

Incoming search terms: