how to remove breaker points on 2003 harley davidson

You search Auto repair manual PDF how to remove breaker points on 2003 harley davidson, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to remove breaker points on 2003 harley davidson Direct Download speed 5282 Kb/s

  how to remove breaker points on 2003 harley davidson Full Version speed 6162 Kb/s



1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

HARLEY DAVIDSON BILLET HEADLAMP WITH SHORT/ TALL MOUNTS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Kit 68593-06 is a 5-3/4 inch headlamp and kit 69851-06 is a 4-1/2 inch headlamp. Both kits will fit the models listed in Table 1. Table 1. Short and Tall Mount Kits Models Kits 1984-1999 FXSTC, 1998- Later FXST/B, and 2000-Later FXSTD; 1994-2005 FXDWG Short Mount Kit 68595-06 1996-Later XL 1200C and 1998-Later XL 883C; All 2006 Dyna Models; 1999-2000 FXR2/3/4 Tall Mount Kit 69611-06 Additional Parts Required This kit also requires the separate purchase of a Short or Tall Mounting Kit 68595-06 or 69611-06 for your model motorcycle, and can be purchased from a Harley-Davidson dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 21, Table 2 and Figure 22, Table 3. REMOVAL Remove Headlamp and Mounting Bracket for Softail Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. 2. Remove fuel tank. Refer to FUEL TANK in Service Manual. 3. Disconnect 4-place headlamp connector [38] from main wire harness. Headlamp connector is located under fuel tank on left side. 8 5 7 5 6 2 1 3 4 is01835 1. Screw 2. Washer 3. Nut 4. Lockwasher 5. Washer (2) 6. Screw 7. Mounting block 8. Headlamp assembly Figure 1. Softail and Dyna Headlamp Assembly with Mount (except FXSTD) NOTE All Softails (except FXSTD) complete steps 4 through 6. For FXSTD models complete steps 7 through 9 4. All Softails (except FXSTD): See Figure 1. Remove screw (1) and washer (2) from stem and bracket. Discard screw but save washer for later use. 5. Remove and discard mounting block (7) and headlamp assembly (8). 6. FXSTD models: See Figure 2. Remove screw (1) and washer (2) from stem and bracket. Save screw and washer for later use. 7. Remove and discard nut (3), washers (4), and screw (5). 8. Remove and discard mounting block (6) and headlamp assembly (7). 7 3 4 2 1 4 6 5 is01838 1. Screw 2. Washer 3. Acorn nut 4. Washer (2) 5. Screw 6. Mounting block 7. Headlamp assembly Figure 2. FXSTD Headlamp Assembly with Mount Remove Headlamp and Mounting Bracket for Dyna Models 1. Remove seat following the instructions in the Service Manual. 2. Disconnect negative (-) battery cable. 3. Remove fuel tank. Refer to FUEL TANK in Service Manual. 2 1 is01750 1. Cable strap 2. Wire harness Figure 3. Dyna Service Loop (2005-Earlier) 4. 2005-Earlier FXDWG: See Figures 3 and 4. Remove plug on right side of top frame tube. At service loop, remove cable clip and push wire harness into top frame tube. Pull connector out from hole on right side of tube. 2006-Later FXD: See Figure 5. Remove cover under top frame tube, then pull connector out from opening under tube. 5. Disconnect 4-place headlamp connector [38] from main wire harness

Incoming search terms:

HARLEY DAVIDSON XL CHROME FORWARD CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
2008-05-05 XL CHROME FORWARD CONTROL KIT GENERAL Kit Number 33395-04, 33398-04 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley- davidson.com (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 5, Figure 6 and Table 1. INSTALLATION Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 5. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is 01887 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is 01901 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod. 3. Remove the two screws (6) and right footrest/brake pedal support bracket with attached brake assembly from frame

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

Harley-Davidson Twin Cam Engines Performer RPM Gear Drive Camshaft Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 03-03-2012

download
1. Disconnect the battery, and remove the fuel tank. 2. On engines with the oil tank above the engine, drain the engine oil. 3. Remove the front exhaust pipe to clear the Cam Housing Cover. 4. Remove the Rocker Covers and remove the four 5/16″ bolts and the two 1/4″ bolts holding the rocker arms in place. With the rocker arms removed, remove the stock pushrods. 5. Remove the push rod tube retaining clips and push rod tubes. 6. At this point, you may remove the lifter covers and take the lifters out, or you can make a lifter holding tool from a binder clip as shown in Figure 1 INSTALLATION PROCEDURE 1. Disconnect the battery, and remove the fuel tank. 2. On engines with the oil tank above the engine, drain the engine oil. 3. Remove the front exhaust pipe to clear the Cam Housing Cover. 4. Remove the Rocker Covers and remove the four 5/16″ bolts and the two 1/4″ bolts holding the rocker arms in place. With the rocker arms removed, remove the stock pushrods. 5. Remove the push rod tube retaining clips and push rod tubes. 6. At this point, you may remove the lifter covers and take the lifters out, or you can make a lifter holding tool from a binder clip as shown in Figure 1 . 7. On pre-2000 models with a cam position sensor, you may want to remove the inspection cover, unplug the wires, and remove the sensor at this time to ease installation later on. 8. Remove the cam housing cover keeping the bolts in a separate cup. ( Note: Oil will run out of the cam housing.) 9. Using the Chain Tensioner Unloader Tool, unload pressure on the outside chain tensioner, and pin it in place with the retaining pin (See Figure 2) .

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

Incoming search terms: