how to remove rear crankcase cover on 2006 honda rancher

You search Auto repair manual PDF how to remove rear crankcase cover on 2006 honda rancher, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to remove rear crankcase cover on 2006 honda rancher Direct Download speed 5282 Kb/s

  how to remove rear crankcase cover on 2006 honda rancher Full Version speed 6162 Kb/s



GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

HARLEY DAVIDSON ENGINE/TRANSMISSION INTERFACE AND TOP COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 1 4 3 2 is03621 1. Transmission top cover screw (3) 2. Upper and lower rear bearing housing screw (2) 3. Upper front bearing housing screw 4. Lower front bearing housing screw Figure 1. Interface Cover Installation 2. See Figure 1. Remove the two rear bearing housing screws (2) from the side of the transmission case. 3. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 4. See Figure 2. Obtain the rear interface mounting bracket (1) from the kit. 5. Apply a few drops of Loctite 243 (Blue) to the threads of the two bearing housing screws removed in Step 2. Install the rear interface mounting bracket to the bearing housing with the screws, and tighten to 13-18 ft-lbs (17.6-24.4 Nm) . 6. See Figure 1. Remove the upper front bearing housing screw (3) from the side of the transmission case. Loosen the lower front bearing housing screw (4). 7. See Figure 2. Obtain the front interface mounting bracket (2) from the kit. 8. Apply a few drops of Loctite 243 (Blue) to the threads of the upper front bearing housing screw removed in Step 6. Hook the slot in the front interface mounting bracket under the loosened lower screw head. Install the bracket to the bearing housing with the upper screw, and tighten both screws to 13-18 ft-lbs (17.6-24.4 Nm) . 9. See Figure 1. Remove and retain the three socket head cap screws (1) that fasten the right side and left front corner of the transmission cover. 10. Remove and retain the screw fastening the rear brake line P-clamp to the rear fork bracket. 11. See Figure 2. Obtain the right rear interface cover (3), two chrome 1/4-20 screws (6) and two flat washers (7) from the kit. 12. From the rear of the motorcycle, bring the right rear interface cover into position behind the rear exhaust pipe, over the bearing housing. The hole in the top surface of the cover should be positioned over the right rear transmission top cover hole. 13. Loosely fasten the interface cover to the rear interface mounting bracket with the two chrome screws and flat washers. 14. Obtain the chrome top interface cover (4) from the kit. 15. Position the top interface cover over the transmission top cover, overlapping the tab at the top front of the chrome right rear interface cover

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

2002-2004 TRIUMPH BONNEVILLE AMERICA/ SPEEDMASTER CARBURETOR KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-10-2010

download
A.) REAR WHEEL REMOVAL- PAGE 14-16 Triumph Motorcycle Service Manual 1.) Support motorcycle on center stand or center lift so rear wheel is suspended and there is clearance for removal. Use tie downs. 2.) If both wheels are raised chock the front wheel to prevent any weight shift when rear wheel is removed. 3.) Remove chain guard. 4.) Remove caliper and support so there is no strain on the brake line. 5.) Remove both silencers from exhaust headers. 6.) Remove axle nut and washer—support or chock rear wheel—and slide out axle. 7.) Disengage chain from sprocket and hang over swing—use soft cloth to protect swing arm from scratches that will occur if you do not cover. 8.) Lower wheel to the ground and collect spacer and caliper support arm and all fasteners for re-assembly. B.) REMOVE SEAT PAGE 15-9 Triumph Motorcycle Service Manual 1.) Remove the 12 mm bolt from rear seat section—if you have a pillion pad remove it first by removing the 8 mm bolt, slide forward and lift free of seat catch. Take a position where you can see what you are doing or you will scratch your painted surface. 2.) Lift seat from the rear and slide backwards to disengage tongue– collect all fasteners for re-assembly. C.) REMOVE REAR MUD GUARD PAGE 15-14 Triumph Motorcycle Service Manual 1.) Disconnect battery and remove from motorcycle. 2.) Disconnect electrical connectors on the underside of the mudguard. 3.) Support fender from beneath and remove the 4 side allen head mount bolts and 2 12mm hex head top front mount bolts– collect all fasteners for re-assembly. D.) REMOVE FUEL TANK PAGE 9-11 Triumph Motorcycle Service Manual 1.) Turn off fuel tap. 2.) Remove fuel line at the tap connection. 3.) Remove the 12mm rear tank-mounting bolt. 4.) With assistance from another set of hands support tank at the rear and lift so that the breather line is visible on the right side of the underside of tank—remove and plug line. 5.) With tank raised and supported at the rear slide backwards— disengaging it from the front mounting rubbers—set tank aside in a safe place to prevent any damage to the painted surface. E.) REMOVE SIDE COVERS PAGE 15-10 and 9-15 Triumph Motorcycle Service Manual 1.) Loosen and remove left side cover screws on the air filter facade— lift slightly to disengage top mounts and remove—set aside in a safe place to prevent damage to painted surface. 2.) On right side cover simply and gently pull bayonet fittings from rubber slip mounts. 3.) Secure these rubber mounts and remove for later re-assembly with the Bonneville Performance brackets.

Incoming search terms:

Incoming search terms: