how to remove regulator from a 1998 honda acer tour

You search Auto repair manual PDF how to remove regulator from a 1998 honda acer tour, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to remove regulator from a 1998 honda acer tour Direct Download speed 5282 Kb/s

  how to remove regulator from a 1998 honda acer tour Full Version speed 6162 Kb/s



GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

HARLEY DAVIDSON BOOM! AUDIO BASS BOOSTER TOUR-PAK PORT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
PREPARATION NOTE For vehicles equipped with security siren: • Verify that the Hands-Free Fob is present. • Turn the ignition key switch to IGNITION. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the owner’s manual and follow the instructions to remove the main fuse. INSTALLATION NOTE The Tour-Pak does not need to be removed from the vehicle to perform this installation. 1. Open the Tour-Pak lid and remove all items from the Tour- Pak base. 2. Models equipped with mat: Remove the mat. Models equipped with liner: Open the map pocket, and remove the acorn nuts with flat washers. Remove the map pocket and liner. 3. Remove four screws from the left-side speaker grille on the Tour-Pak. Remove the speaker grille from the speaker pod. 4. Remove the speaker from the speaker pod. Carefully pull the two socket terminals from the speaker spade contacts. 5. Remove the grommet, and draw the rear speaker/passenger controls connector out of the speaker pod. Separate the connector halves. 6. Repeat Steps 3 through 5 for the right-side speaker. 7. See Figure 1. Get the drill template (3) from the kit. If NOT equipped with power port: a. Remove one speaker pod mounting screw and flat washer. b. Align the drill template on the inside of the Tour-Pak with the speaker pod holes, and hold in place with the mounting screw and washer. c. Repeat for the remaining template mounting holes. If equipped with power port: a. Remove the two screws and flat washers to free the power port from the Tour-Pak. b. Align the drill template on the inside of the Tour-Pak with the power port holes, and hold in place with the mounting screws and washers. c. Repeat with the top speaker pod mounting screw and flat washer. NOTE Tighten the screws enough to hold the speaker pod in place as the pilot hole is drilled. 8. Where indicated on the template, drill a 3/16 inch (5 mm) diameter pilot hole through the Tour-Pak wall and speaker pod. 9. Remove the screws and speaker pod, and set aside. Turn the template over, and repeat Steps 7 and 8 on the left side of the Tour-Pak. NOTE Hole size will affect the fitment of the ports. The hole saw needs to be sharp. 10. Carefully drill a two inch (51 mm) diameter hole with a sharp hole saw, at the pilot location, through each speaker pod and in both locations on the Tour-Pak wall. 11. Temporarily install the Tour-Pak liner (if equipped), and mark the location of the two inch (51 mm) diameter holes on the outside of the liner. Remove the liner, and carefully cut the two holes in the liner front wall

Incoming search terms:

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK WALL ORGANIZER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
This kit fits 1997 and later models equipped with King Tour- Paks INSTALLATION NOTE Maximum Wall Organizer weight capacity is 3 pounds (1.4 Kg) evenly distributed. Do not exceed tour-pak weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00401b) Tour-Paks With Molded Liner 1. Remove the two nuts that hold the pouch and liner in the Tour-Pak. Remove pouch and liner and carefully wash the inside of the Tour-Pak with warm, soapy water. Rinse and dry thoroughly. 2. Use the alcohol prep pad in the kit to thoroughly clean the interior surface of the Tour-Pak sides where fastener strips will be attached. Make sure any residue is removed, then allow Tour-Pak to dry completely. Make sure the surface is free of condensed moisture. NOTES The hook and loop fastener strips and organizer must be installed below the edge of Tour-Pak base to avoid interference with top gasket and lock. The ideal temperature range for applying the fastener strip is 70-100° F (21-38° C). Minimum application temperature is 50° F (10° C). If you attempt to apply the tape below these temperatures, the adhesive will become too firm to adhere readily. 3. See Figure 1 and Figure 2. Remove the hook and loop fastener strips from the hinged hook and loop strips. Remove the paper backing and firmly press the fastener strips into the locations (1) shown in Figure 2. The fastener strips should be located approximately 1/8 in. (3 mm) below the edge of the Tour-Pak base. 4. See Figure 1. Bend the hinged hook and loop strips (3) into shape as shown. Attach the hinged strips onto the fastener strips (2) installed in Step 3. NOTE The Tour-pak Wall Organizer installs in place of the pouch removed in Step 1, therefore the pouch will not be re-installed. 5. Reinstall the liner removed in Step 1. The hinged strips (3) will go over the top of the liner (4) as shown in Figure 1. 6. See Figure 1. Attach the organizer (5) to the hinged strips (3). Adjust the organizer’s lock cut out so that it is centered around the lock, and press the hook side of the hook and loop strips on the bottom of the organizer into place on the liner. The hook side will attach to the liner. NOTE 2006 and later Tour-Paks equipped with Passenger Backrest will have two acorn nuts at the front of the base. Remove and discard the 8 in. (200 mm) long hook and loop hinged fastener strip from the center panel. In one of the organizer pockets there will be 4 in. (100 mm) and 1-1/2 in. (38 mm) hook and loop hinged fastener strips. Install the hinged strips on the organizer center panel as shown in Figure 3. 7. Check to make sure the Tour-Pak lid closes over the organizer and the lock works without interference. Adjust as necessary. 8. Allow tape to cure (“wet-out”) for a minimum of 48 hours at 70° F (21° C) (allow extra time if temperature is below 70°). Do not place items in the Wall Organizer while adhesive is curing

HONDA 420 RANCHER 2×4/4×4 2007-2009 CLUTCH KIT INSTRUCTIONS

0

Filed Under (Honda) by admin on 22-12-2011

download
Remove key from the ignition switch. Remove the side panels from both sides. Remove both foot wells. 2. Drain coolant. Remove the oil drain plug from the motor; if you carefully drain it into a clean container you should be able to reuse it. 3. Disconnect shift motor (on electric shift models only). Remove coolant hoses. 4. Remove the bolts that mount the front differential to the frame, no other parts need to be removed. Carefully slide the front differential towards the front of the machine; you might need to lift up slightly to get the differential to move. Remove the drive shaft. Remove o-ring on output shaft (on motor). 5. Remove the fuel pump. 6. Loosen the front crankcase cover bolts, keep track of each bolt length and location. Slowly remove the crankcase cover. Carefully watch for o-ring shims and dowel pins that may fall out. 7. Unstake the nut holding the clutch on and remove nut. Using Honda tool #07933-HB3000A thread the large part of the tool into the center of the clutch. Tighten the center bolt on the tool while holding the large part of the tool with a wrench. This will pull the clutch off the machine. Place the clutch on a clean work surface. EPI performance.com
8. Using the c-clamps push down slightly on the outside cover and remove the four e-clips. Keeping track of which way they come off, remove the round metal plates one at a time. This will allow you to see the complete spring. Remove one end of each spring using a spring tool or needle nose pliers and then remove springs. Install the EPI springs by inserting the spring into the outer edge first. Using a spring tool or pliers (45 degree bent pliers work well) pull on the spring and insert the end into the hole. Install the metal plates and the e-clips. If you can’t get the plates to sit flat make sure each clutch arm is flat against the bottom plate of the clutch. Occasionally when you put the springs on, the clutch arms will pop up. Slide the clutch into the machine. The Sprague clutch is marked “outside” when installing make sure this is facing out. Torque clutch nut to 87 ft/lbs. 9. Clean the gasket surface on the motor and on the cover. Put a thin layer of Honda Bond or Yamabond semi-drying liquid gasket (or something similar as long as it is semi-drying) on the crankcase cover. Carefully install crankcase cover, do not force cover on. Torque bolts to 9 ft/lbs. 10. Install the fuel pump. 11. Install the o-ring on the output shaft (on motor) and install the drive shaft. Carefully slide the front differential back into place and mount to the frame. Install the coolant hoses. Refill your engine coolant to the proper level according to your owner’s manual. 12. Install the oil drain plug. Refill your engine to the proper level according to your owner’s manual. You can reuse your oil if it is clean and was drained into a clean container. Only use manufactures recommended oil. 13. Be sure to double check coolant and oil levels and to look for any leaks after the machine has run for a few minutes. 14. Go out and ride your machine. If your performance doesn’t seem right double check to make sure everything has been done properly. 15. EPI is constantly testing our products. Sometimes there is a need to contact the user with new technical information. To ensure that you are receiving this information visit our web site EPIperformance.com to register your clutch kit.

Incoming search terms:

HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

HARLEY DAVIDSON TOURING DETACHABLE TOUR-PAK RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION NOTE See Figure 3. When installing Tour-Pak to Rack in the following Steps, note that holes on Rack provide two positions for mounting Tour-Pak in desired location. 1. Place Tour-Pak on support tube and open lid. NOTE See Figure 3. In the following step, the longer bolts (6) are used for 2005 and earlier (King only) and Chopped Tour-Paks while the shorter bolts (5) are used for Leather Tour-Pak and 2006 and later King Tour-Paks. 2. See Figure 3. Obtain bolt (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align rear center hole in Tour-Pak with same hole in support tube (8). Slide bolt with flat washer through Tour-Pak, through support tube, then through concave spacer (with concave side facing support tube). At bottom of support tube, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. 3. Obtain bolts (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align top support tube (8) with detachable tour-pak rack holes (four). Slide bolts with flat washer through Tour-Pak, through support tube, through concave spacer (with concave side facing support tube) then through rack. At bottom of detachable tour-pak rack, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. NOTE Always install the mounting bolts from inside the Tour-Pak. If the bolts are installed upside down, then the ends of the bolts can tear the molded liner and scratch objects, such as helmets, stored inside the Tour-Pak. 4. Repeat Step 3 and install hardware to the remaining three holes in Tour-Pak and mounting rack. 5. In a crosswise pattern, alternately tighten the five bolts to 96-120 in-lbs (10.8-13.5 Nm) . Be sure that concavity on each spacer is inline with the rail and has not rotated out of position. INSTALLATION-TOUR-PAK AND RACK 1. Follow the instructions included in the docking point kit and install docking points. 2. See Figure 1. While standing behind the motorcycle, place the front Tour-Pak rack notches into the front docking points (1). Make sure the notches seat fully into the front docking points. 2 1 is04025 1. Front Docking Point 2. Rear Docking Point Figure 1. Docking Point Bracket 3. See Figure 1 and Figure 2. Position the latches over the rear docking points (2). Check to be sure the latches fit into the neck of the rear docking points as shown in figure 2. This may require some gentle squeezing or spreading of the rack

Incoming search terms:

Incoming search terms: