how to remove subframe on yamaha virago 1100

You search Auto repair manual PDF how to remove subframe on yamaha virago 1100, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to remove subframe on yamaha virago 1100 Direct Download speed 5282 Kb/s

  how to remove subframe on yamaha virago 1100 Full Version speed 6162 Kb/s



GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

Incoming search terms:

Yamaha V-Star 1100 Jetting the Carburetors INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-03-2012

download
Remove air filter housing Remove the seat or seats Disconnect Fuel Lines (also the vapor line from tank to charcoal canister on California models) Disconnect instrument connectors from the fuel tank Remove fuel tank Remove air box Disconnect TPS and heater connectors Remove chrome carb cover Disconnect Fuel Lines Remove rubber carb elbows Disconnect throttle cables from carbs Remove the carbs Perform the jetting 1. Remove the Chrome air filter housing. To remove the chrome dog-dish (air filter housing) from the right side of the bike, you will need to remove the two mounting bolts and loosen the clamp that holds the air duct to the back of the housing. You will need a 5 mm Allen wrench and a #2 Philips screwdriver. 2. Remove the seats. This can be accomplished by using a 5 mm Allen wrench and removing the Allen head bolt from just behind the rear seat and the bolt just behind the front seat. Pulling up and back will free the seats. One smooth motion will do it. 3. Gain access to the dashboard plug and unplug it (It is white) Note: Your trip odometer will lose its count, please record the number if you wish to save your current mileage for this tank of gas. Figure A shows the three plastic rivets that need to be removed to gain access to the dashboard plug. Using your Philips head screwdriver, press the small circle in the middle of the rivets down… a click is felt. Remove the rivets by hand. You have freed the cover and you may lift it up to expose the electrical connector that needs to be unplugged. Figure B shows the plug

Incoming search terms:

Yamaha Road Star 1600/ 1700 Exhaust kit bill of materials Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove left side cover, by removing allen bolt as shown (Fig 1). Once bolt is removed, push cover to motor and push back carefully to your upper body. Figure 1 2. Once left side cover is removed, remove 6mm bolt to opposite side cover as shown (Fig. 2). Also remove allen bolt on right side as shown (Fig 3) and remove carefully . Figure 2 Figure 3 . Remove two allen bolts to the muffler bracket, and also loosen hose clamp to bottom head pipe. (Fig 4 & 5) Figure 4 Figure 5 4. Remove bolt next to rear O/2 sensor bracket as shown (Fig 6), also remove Phillips head bolt from O/2 bracket and slide O/2 sensor off bracket as shown (Fig 7). Once bracket is removed mount just bracket on with Phillips head bolt back on. Figure Figure 7 5. Disconnect O/2 by using a pick on inside switch on opposite side of O/2 bracket. With pick on inside push to you and unplug. (Fig 8 & 9) Figure 8 Figure 9 6. Remove two socket cap nuts from rear head pipe flange as shown (Fig 10). Once removed, remove both mufflers and rear head pipe carefully. Slide muffler back and shift rear head pipe to you. (Fig 11) Figure 10 Figure 11 7. Slide wire off bracket from the front O/2 sensor as shown (Fig 12). Also use pick to remove O/2 sensor, push to you and unplug. Figure 12 Figure 13
8. Remove two allen bolts from foot rest/ brake to give you access to head pipe. (Fig 14) Figure 14 9. Remove two allen socket cap nuts off front head flange and remove head pipe. (Fig 15) Figure 15 10. Remove stock muffler bracket by removing two alien bolts as shown (Fig 16). Also remove bolt that holds stock bracket to the brake line (Fig 17). Once that is done remove brake line from caliper and slide though muffler bracket and re-install. Figure 16 Figure 17
Assembly 11. Remove O/2 sensor from stock pipe and install O/2 sensor in Roadhouse front head pipe and mount front head pipe with stock socket cap nuts on bike as shown. (Fig 18 & 19) Figure 18 Figure 19 12. Mount rear head pipe as shown (Fig 20), including stock socket cap nuts. Also mount y-collector with rear head pipe. Y-collector must slide into front head pipe in one. Install Roadhouse O/2 sensor wire lead from hardware kit into y-collector. (Fig 21) Figure 20 Figure 21

Incoming search terms:

HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

Yamaha V-Star 1100 Custom and Classic cruisers Floorboard/ Footpeg Extension Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Start on the right (brake) side. 1) Loosen the nut at the end of the brake rod. This will allow you to unscrew the brake rod from the brake lever clevis later. 2) Pull out the cotter pin and remove the pivot pin. Unscrew the clevis 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the brake floorboard/footpeg assembly (whichever your bike has) to the frame. These bolts are torqued to 46 ft lbs, so this may be a bit difficult. 1. Loosen this nut 2. Remove the cotter pin (other side of this pivot pin) remove the pivot pin a unscrew the nut to remove the clevis nd 3. Remove these bolts When you remove the floorboard/footpeg bracket, be careful not to pull the brake switch wires loose. You may wish to cut the cable tie for more room, and then rest the bracket, with the footpeg or floorboard attached, on a short box, or block of wood, to keep it handy. Install the new brake rod, to the end of the existing brake rod. Re-install the pivot pin, and the pivot pin cotter pin. Installing the extension bar: Note that the extension bar is bolted so that it rises up in front. Use the new bolts to mount the floorboard/ footpeg bracket to the threaded holes in front. Install the Extension in the proper orientation (angled holes bolt up to the frame, with front of the bar higher than the rear – see photo) using the stock bolts for the extensions to the frame and the new bolts and washers supplied with the kit, on the forward threaded section to relocate the floorboard or footpeg bracket. The use of LocTite ® Blue here is recommended. At this point the right side Floorboard or Footpeg should be secured tightly and the brake lever hanging loose. Now install the Brake rod extension, threading the male end to the original brake rod. Don’t tighten this end yet Place the clevis over the forward most end of the brake rod extension, and threat the clevis nut onto the end of the rod. Bring the brake rod upright, to meet with the clevis at the end of the brake rod extension and replace the pivot pin. Before reinstalling the cotter pin, check the angle of the brake lever, to insure that you have the brake pedal where you want. If necessary, adjust the extension rod in or out, until you are satisfied, and then reinstall the cotter pin into the pivot pin. Check the Brake switch wire and install a new cable tie if required. Note: Due to utilizing a thicker material, 1/2″ versus 3/8″ from our competitor, the Brake rod is now positioned at a greater angle. Even with the angle, braking performance is not affected, but if you wish to bring the master cylinder in line with the brake rod, do this. Loosen the rear, and remove the front Allen bolt. Then place two washers behind the front bolt, under the bracket, and then re-install the bolts To change the angle of the brake rod, 1) loosen and remove the two master cylinder bracket Allen bolts 2) insert two washers behind the front bolt (front of the bike), behind the master cylinder bracket 3) tighten both bolts. Do not install any washers on the rear mounting hole. This will make the angle of the Brake Rod less aggressive. Step Two – Left Side For the left (Shifter) side, 1) use an open-end 10 mm wrench, to unscrew the two nuts that hold the shift rod in place. PLEASE note that one end of the shift rod has a left hand threaded nut. SAVE the nuts, as you will need them on the new longer Polished Stainless Steel Shift Rod. 2) Remove the stock shift rod. 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the shifter floorboard/footpeg assembly (whichever your bike has) to the frame.

Incoming search terms:

Incoming search terms: