how to remove the catalyst from the harley head pipe

You search Auto repair manual PDF how to remove the catalyst from the harley head pipe, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to remove the catalyst from the harley head pipe Direct Download speed 5282 Kb/s

  how to remove the catalyst from the harley head pipe Full Version speed 6162 Kb/s



GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

Yamaha Road Star 1600/ 1700 Exhaust kit bill of materials Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove left side cover, by removing allen bolt as shown (Fig 1). Once bolt is removed, push cover to motor and push back carefully to your upper body. Figure 1 2. Once left side cover is removed, remove 6mm bolt to opposite side cover as shown (Fig. 2). Also remove allen bolt on right side as shown (Fig 3) and remove carefully . Figure 2 Figure 3 . Remove two allen bolts to the muffler bracket, and also loosen hose clamp to bottom head pipe. (Fig 4 & 5) Figure 4 Figure 5 4. Remove bolt next to rear O/2 sensor bracket as shown (Fig 6), also remove Phillips head bolt from O/2 bracket and slide O/2 sensor off bracket as shown (Fig 7). Once bracket is removed mount just bracket on with Phillips head bolt back on. Figure Figure 7 5. Disconnect O/2 by using a pick on inside switch on opposite side of O/2 bracket. With pick on inside push to you and unplug. (Fig 8 & 9) Figure 8 Figure 9 6. Remove two socket cap nuts from rear head pipe flange as shown (Fig 10). Once removed, remove both mufflers and rear head pipe carefully. Slide muffler back and shift rear head pipe to you. (Fig 11) Figure 10 Figure 11 7. Slide wire off bracket from the front O/2 sensor as shown (Fig 12). Also use pick to remove O/2 sensor, push to you and unplug. Figure 12 Figure 13
8. Remove two allen bolts from foot rest/ brake to give you access to head pipe. (Fig 14) Figure 14 9. Remove two allen socket cap nuts off front head flange and remove head pipe. (Fig 15) Figure 15 10. Remove stock muffler bracket by removing two alien bolts as shown (Fig 16). Also remove bolt that holds stock bracket to the brake line (Fig 17). Once that is done remove brake line from caliper and slide though muffler bracket and re-install. Figure 16 Figure 17
Assembly 11. Remove O/2 sensor from stock pipe and install O/2 sensor in Roadhouse front head pipe and mount front head pipe with stock socket cap nuts on bike as shown. (Fig 18 & 19) Figure 18 Figure 19 12. Mount rear head pipe as shown (Fig 20), including stock socket cap nuts. Also mount y-collector with rear head pipe. Y-collector must slide into front head pipe in one. Install Roadhouse O/2 sensor wire lead from hardware kit into y-collector. (Fig 21) Figure 20 Figure 21

Incoming search terms:

HARLEY DAVIDSON Dresser 2-1 Pro Pipe HS Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place motorcycle on side stand. Remove both left and right saddlebags. 2. Loosen pinch clamp bolt on front end of each muffler. Note : On older model Dresser exhaust, spread clamps just enough to remove them. 3. Remove two 5/16″ bolts holding the left and right mufflers to the saddlebag supports. 4. Remove stock mufflers and set them aside. Note : It may be necessary to use a penetrating lubricant on slip joint between muffler and head pipe. 5. Loosen heatshield clamps on both front and rear head pipes. 6. Loosen the left rear head pipe mounting clamp located behind the rear cylinder. Remove the section of head pipe that connects to left side muffler. 7. Remove 3/8″ bolt from the head pipe clamp that secures front head pipe to the transmission bracket. 8. Remove right hand floor board. 9. Remove flange nuts that secure each head pipe to cylinder head. Carefully remove the head pipes and set them aside. 10. Carefully remove flanges and circlips (save) from the stock exhaust system using snapring pliers. Note: Replace bent or damaged circlips. 11. Remove stock transmission bracket. To access standard transmission bracket, first remove oil dip stick cover and clutch release cover. Refer to figure 1. Note : If motorcycle is resting in a near vertical position, engine/transmission oil must be drained completely before removing covers. Loosen and remove four allen bolts and stock transmission bracket. (save)

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

HARLEY DAVIDSON DYNA LongShot Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove both front and rear head pipe clamp bolts. 4. Remove the entire exhaust system and set it aside. 5. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips. 6. Remove the rear head pipe clamp bracket from the transmission cover. Save the bolts, two will be reused. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Locate the muffler mounting bracket (stamped 239). Mount the bracket to the engine case, to the rear of the transmission cover using the two stock bolts. Refer to figure 1. Tighten the bolts at this time. Install the mounting bar (supplied) to the transmission housing using the stock hardware. Refer to figure 1 . Note: The mounting bracket should mount flatagainst the transmission housing. Some motorcycles use a stud to mount the stock rear head pipe clamp, be sure to remove the stud from the transmission housing and replace it when mounting the bracket, this will insure that the bracket is flat against the housing. 2. Locate the muffler clamp bracket (stamped 240). Install the bracket to the outside of bracket 239, using the 5/16″x 1 1/4″ bolt and 5/16″ flat washer (supplied). Refer to figure 1. Leave the bracket loose, it will be adjusted later. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the circlips and flanges from the stock system onto both the new head pipes. 5. Slide the new pipe clamp (supplied) onto the muffler end of the front head pipe. Position the clamp in the approximate mounting location on the pipe. 6. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the rear head pipe.

Incoming search terms:

HARLEY DAVIDSON TOURING MODEL DRESSER DUALS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-12-2010

download
1. Remove both left and right saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffl er. 3. Remove the two 5/16″ bolts that mount the muffl er to the saddlebag supports. Repeat this step on the opposite muffl er (save these parts, they will be re-used). 4. Remove the stock muffl ers with sliding hangers and set them aside. NOTE: It may be necessary to use a penetrating lubricant to loosen the muffl er from the head pipe. 5. Find and unplug the O2 sensor wires from the wiring harness and remove cable tie holding front wire to frame. F eed the end of the wires through the frame so they are free from the motorcycle. NOTE: Pay attention to wire routing for re-installation. 6. Remove the right hand fl oor board. 7. Remove both passenger fl oor boards. 8. Loosen the heat shield clamps on both front and rear exhaust pipes. 9. Loosen the rear head pipe clamp located behind the rear cylinder. Remove the section of head pipe connecting the left side muffl er. 10. Remove the nut and carriage bolt holding the front head pipe to the bracket on the transmission housing (save these parts, they will be re- used). 11. Remove the two mounting nuts from each head pipe, located at the cylinder head. Carefully remove the head pipes and set them aside. 12. Using a 22mm wrench, carefully remove the O2 sensors from the stock head pipes and save for re-use with the new system. 13. Remove the rear cylinder bracket by removing the two starter mounting bolts. Install new bracket (stamped 422-P)(supplied) and torque to 13-16 ft. lbs. (Figure 1). NOTE: Twist breather hose down towards the left hand side to get it as far away from the pipe as possible. 14. Install mounting post (from stock system) so the nut is accessible from right side of motorcycle and saddle will support underside of exhaust pipe. 15. Replace the bracket on the transmission housing with new bracket (stamped 423-P)(supplied) and torque to 13-16 ft. lbs. (Figure 2). 16. Carefully remove the exhaust port fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted, replace them.

YAMAHA VIRAGO 700/ 1100 2 into 2 EXHAUST SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the slip joint clamp on the front and rear head pipe, which are located at the muffler box. 2. Remove the two nuts that hold the front head pipe to the engine. Slip the head pipe out of the muffler box and set it aside. Note: Do not remove the rear head pipe, it has been incorporated in the design of the new exhaust system. 3. Remove the muffler box mounting bolt located in front of the passenger foot rest on the left side. 4. Remove two bolts from the right passenger foot rest assembly and set the foot rest aside. 5. Slide the muffler box off of the rear head pipe and set it aside. 6. Replace the muffler box mounting bolt (from step #3) using the washer and nut (supplied) on the back side. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Attach the mounting bar to the motorcycle frame behind the right passenger foot rest. Align the two holes in the largest bracket on the mounting bar with the two holes on the frame, be sure the bend in the mounting bar is pointing to the center of the motorcycle. 2. Install the round steel spacer (supplied) to the rear most hole in the bracket. 3. Attach the foot rest using the two 8mm x 1.25 x 25mm bolts (supplied). 4. Slide the new exhaust flange (supplied) onto the front head pipe. 5. Install the two heat shields to the front head pipe using the four hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the heat shields onto the front head pipe. Note: Be sure the bend in the heat shield matches the bend in the head pipe exactly. Wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 6. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 7. Slide a chrome pinch clamp (supplied) onto the expanded end of the new rear head pipe. Install a 3/8″ x 1″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Repeat this step on the inlet end of each muffler using the two muffler clamps with 5/16″ x 1 1/4″ bolts (hardware supplied) but leave the clamp loose at this time. 8. Slip the new rear head pipe with the heat shield attached, over the stock rear pipe and gasket, but leave the clamp loose at this time. 9. Install the front head pipe, with the heat shield attached and stock gasket in place, to the front cylinder using the stock nuts, leave them loose at this time

Incoming search terms:

Harley davidson American Classic Straights on a 1988-2001 VLX 600 Shadow Installation Instructions

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system.
1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install nut strip into slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — DO NOT TIGHTEN NUTS! 8. Install nut strip into slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks.

Incoming search terms:

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

Incoming search terms:

Incoming search terms: