how to remove the gas tank on a yamaha vstar1300

You search Auto repair manual PDF how to remove the gas tank on a yamaha vstar1300, if there are search results will appear below. If search results do not exist, please search by others keyword.





GL1800 Goldwing Trike Conversion Kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

Ducati Hypermotard Large Fuel Tank Installation Instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
REMOVING THE OEM FUEL TANK GO FOR A RIDE The best way to remove fuel from your original fuel tank is to RIDE your bike. You should already be familiar with how low you can go and the less fuel that’s in your tank before you start means the less mess you make when draining it. HM69 Fuel Tank Installation Instructions This manual is provided for marketing and informational purposes only and is a guide to assist experienced motorcycle technicians with the installation of the HM69 fuel tank. This installation involves gasoline. Improper installation, adjustment, alteration, service or maintenance regarding the HM69 fuel tank can cause property damage, personal injury or death. At-home Do-It-Yourself mechanics should not install the HM69 fuel tank if you are uncertain of your ability to properly install it and refer the installation to an authorized Ducati service department. ! REMOVE THE SEAT Remove the seat bolt at the rear of the seat with a 4mm hex key. To remove the seat, grasp both sides of the seat, lift the rear of the seat slightly, and pull the seat to the rear of the bike. The front of the seat engages onto bolts on either side of the fuel tank and can be stubborn. THIS KIT ALSO CONTAINS: © 2009 California Cycleworks, Inc. Questions? Email orders@ca-cycleworks.com 1
REMOVE THE BODYWORK The tank cover is fi rst. Remove the fuel fi ller cap and then the 4 screws you see: 2 near the front of the cover and the two aside the fi ller neck. Lift up on the forward portion of the cover and move the entire cover rearward so that the back of the cover is away from the retaining contour on the fuel tank. SIDE PANELS Remove the right side panel’s inner cover using a large coin. Both left and right side covers are retained by 3 screws with 4mm hex heads. Remove the 2 screws on the side of the tank (which were revealed with the removal of the seat). While holding the side covers to support them, remove the bottom screw. The left side cover pulls away naturally – take care not to drop the cover as the tool kit is housed inside of it, adding unexpected weight

2002-2004 TRIUMPH BONNEVILLE AMERICA/ SPEEDMASTER CARBURETOR KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-10-2010

download
A.) REAR WHEEL REMOVAL- PAGE 14-16 Triumph Motorcycle Service Manual 1.) Support motorcycle on center stand or center lift so rear wheel is suspended and there is clearance for removal. Use tie downs. 2.) If both wheels are raised chock the front wheel to prevent any weight shift when rear wheel is removed. 3.) Remove chain guard. 4.) Remove caliper and support so there is no strain on the brake line. 5.) Remove both silencers from exhaust headers. 6.) Remove axle nut and washer—support or chock rear wheel—and slide out axle. 7.) Disengage chain from sprocket and hang over swing—use soft cloth to protect swing arm from scratches that will occur if you do not cover. 8.) Lower wheel to the ground and collect spacer and caliper support arm and all fasteners for re-assembly. B.) REMOVE SEAT PAGE 15-9 Triumph Motorcycle Service Manual 1.) Remove the 12 mm bolt from rear seat section—if you have a pillion pad remove it first by removing the 8 mm bolt, slide forward and lift free of seat catch. Take a position where you can see what you are doing or you will scratch your painted surface. 2.) Lift seat from the rear and slide backwards to disengage tongue– collect all fasteners for re-assembly. C.) REMOVE REAR MUD GUARD PAGE 15-14 Triumph Motorcycle Service Manual 1.) Disconnect battery and remove from motorcycle. 2.) Disconnect electrical connectors on the underside of the mudguard. 3.) Support fender from beneath and remove the 4 side allen head mount bolts and 2 12mm hex head top front mount bolts– collect all fasteners for re-assembly. D.) REMOVE FUEL TANK PAGE 9-11 Triumph Motorcycle Service Manual 1.) Turn off fuel tap. 2.) Remove fuel line at the tap connection. 3.) Remove the 12mm rear tank-mounting bolt. 4.) With assistance from another set of hands support tank at the rear and lift so that the breather line is visible on the right side of the underside of tank—remove and plug line. 5.) With tank raised and supported at the rear slide backwards— disengaging it from the front mounting rubbers—set tank aside in a safe place to prevent any damage to the painted surface. E.) REMOVE SIDE COVERS PAGE 15-10 and 9-15 Triumph Motorcycle Service Manual 1.) Loosen and remove left side cover screws on the air filter facade— lift slightly to disengage top mounts and remove—set aside in a safe place to prevent damage to painted surface. 2.) On right side cover simply and gently pull bayonet fittings from rubber slip mounts. 3.) Secure these rubber mounts and remove for later re-assembly with the Bonneville Performance brackets.

YAMAHA Road Star Fuel Pump Relocation Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and disconnect battery. Remove fuel tank along with both left and right side battery covers, and remove air box from carburetor (all per Yamaha standard shop manual procedures). 2. Remove chrome plastic cover over fuel pump and disconnect choke cable/knob from lower pump bracket. Remove pump-to-carb fuel line from fuel pump. Disconnect fuel pumps electrical lead connector. 3. Remove two (2) hex-head pump mounting bracket bolts and remove pump assembly from motorcycle. Slide fuel pump up and off bracket mounting posts (Caution: excess fuel may drain from pump and/or fuel lines and fuel filter!). Remove heat shield. Remove remaining fuel line from pump. Pull all fuel lines from filter and remove steel springs and hose clamps from these lines (these will be reused on the kits fuel lines). With a sharp knife or box cutter, trim off the top portion of the fuel pumps rubber isolation/mount system per Photo A. Next cut pumps wiring harness approximately half way between connector and pump. Strip the insulation from the ends of these wires as well as from the supplied Baron harness extension wires. Using the supplied electrical butt connectors, crimp Baron harness extensions red wire to pumps black-w/blue-strip wire, and Baron harness extensions black wire to pumps black wire. Repeat this process on other side of wire harness extension with pumps connector. Now, referring to Photo B, you will need to cut off the square tube that runs along the side of the fuel pump with a hack saw. Cut down toward pump body in a straight cut, then cut tube off by cutting along the body. This will allow you to twist pump in the rubber mount so the curved spigot is facing up (clockwise approx 1/4 turn). 4. Remove pump-to-carb fuel line from carb and separate electrical wires from this line. Remove this fuel line from engine. Re-route choke cable to right side of engine (toward carb) and rotate it up and over rear cylinder head back toward left side of bike. Mount new Baron choke bracket to the choke cable and tighten plastic nut. New choke bracket will mount to rear fuel tank mounting location (Photo C). 5. 99~03 models – Remove electrical relay bracket (found under the right side cover) from the bike and slide each relay off of this bracket. Install fuel pump onto new Baron Fuel Pump Bracket and install bracket in the same location as the stock bracket you just removed, using stock mounting hardware. Refer to Photo F for proper installation. 6. 04~07 models Remove electrical relays from stock bracket and remove relays from rubber holder. Cut rubber holder per Photo E and replace one of the relays into the rubber and install on to new Baron bracket. The second relay will be placed to the right of the tool bag under the seat and secured with the provided two-sided tape pad. Reconnect plugs to the relays. (Photo F)

Incoming search terms:

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

Incoming search terms:

Yamaha V-Star 1100 Jetting the Carburetors INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-03-2012

download
Remove air filter housing Remove the seat or seats Disconnect Fuel Lines (also the vapor line from tank to charcoal canister on California models) Disconnect instrument connectors from the fuel tank Remove fuel tank Remove air box Disconnect TPS and heater connectors Remove chrome carb cover Disconnect Fuel Lines Remove rubber carb elbows Disconnect throttle cables from carbs Remove the carbs Perform the jetting 1. Remove the Chrome air filter housing. To remove the chrome dog-dish (air filter housing) from the right side of the bike, you will need to remove the two mounting bolts and loosen the clamp that holds the air duct to the back of the housing. You will need a 5 mm Allen wrench and a #2 Philips screwdriver. 2. Remove the seats. This can be accomplished by using a 5 mm Allen wrench and removing the Allen head bolt from just behind the rear seat and the bolt just behind the front seat. Pulling up and back will free the seats. One smooth motion will do it. 3. Gain access to the dashboard plug and unplug it (It is white) Note: Your trip odometer will lose its count, please record the number if you wish to save your current mileage for this tank of gas. Figure A shows the three plastic rivets that need to be removed to gain access to the dashboard plug. Using your Philips head screwdriver, press the small circle in the middle of the rivets down… a click is felt. Remove the rivets by hand. You have freed the cover and you may lift it up to expose the electrical connector that needs to be unplugged. Figure B shows the plug

Yamaha Road Star 1600/ 1700 Exhaust kit bill of materials Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove left side cover, by removing allen bolt as shown (Fig 1). Once bolt is removed, push cover to motor and push back carefully to your upper body. Figure 1 2. Once left side cover is removed, remove 6mm bolt to opposite side cover as shown (Fig. 2). Also remove allen bolt on right side as shown (Fig 3) and remove carefully . Figure 2 Figure 3 . Remove two allen bolts to the muffler bracket, and also loosen hose clamp to bottom head pipe. (Fig 4 & 5) Figure 4 Figure 5 4. Remove bolt next to rear O/2 sensor bracket as shown (Fig 6), also remove Phillips head bolt from O/2 bracket and slide O/2 sensor off bracket as shown (Fig 7). Once bracket is removed mount just bracket on with Phillips head bolt back on. Figure Figure 7 5. Disconnect O/2 by using a pick on inside switch on opposite side of O/2 bracket. With pick on inside push to you and unplug. (Fig 8 & 9) Figure 8 Figure 9 6. Remove two socket cap nuts from rear head pipe flange as shown (Fig 10). Once removed, remove both mufflers and rear head pipe carefully. Slide muffler back and shift rear head pipe to you. (Fig 11) Figure 10 Figure 11 7. Slide wire off bracket from the front O/2 sensor as shown (Fig 12). Also use pick to remove O/2 sensor, push to you and unplug. Figure 12 Figure 13
8. Remove two allen bolts from foot rest/ brake to give you access to head pipe. (Fig 14) Figure 14 9. Remove two allen socket cap nuts off front head flange and remove head pipe. (Fig 15) Figure 15 10. Remove stock muffler bracket by removing two alien bolts as shown (Fig 16). Also remove bolt that holds stock bracket to the brake line (Fig 17). Once that is done remove brake line from caliper and slide though muffler bracket and re-install. Figure 16 Figure 17
Assembly 11. Remove O/2 sensor from stock pipe and install O/2 sensor in Roadhouse front head pipe and mount front head pipe with stock socket cap nuts on bike as shown. (Fig 18 & 19) Figure 18 Figure 19 12. Mount rear head pipe as shown (Fig 20), including stock socket cap nuts. Also mount y-collector with rear head pipe. Y-collector must slide into front head pipe in one. Install Roadhouse O/2 sensor wire lead from hardware kit into y-collector. (Fig 21) Figure 20 Figure 21

Incoming search terms: