how to replace harley gas gauge dyna

You search Auto repair manual PDF how to replace harley gas gauge dyna, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace harley gas gauge dyna Direct Download speed 5282 Kb/s

  how to replace harley gas gauge dyna Full Version speed 6162 Kb/s



HARLEY DAVIDSON LED FUEL GAUGE KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Removing the Analog Fuel Gauge NOTE The fuel gauge wires are routed through a tube in the fuel tank, and are secured by a clip at the bottom of the tank and, on some models, a clamp on the frame. Open the clip and clamp as needed, and be sure there is enough slack in the wires to be able to lift out the gauge. 1. At the bottom left side of the fuel tank, bend back the flexible clip slightly to free the fuel gauge conduit. Open the harness clamp on the frame if necessary to free the conduit. Gently pull on the conduit to draw the Multilock connector [117] out of the tunnel. 2. See Figure 2. Depress the pin on the socket terminal side of the connector, and pull apart the pin and socket halves. 3. See Appendix B in an appropriate Service Manual. Use a pick (Snap-On TT600-3 or equivalent) to remove the terminals or clip off the wires. Remove and discard the fuel gauge. 4. For Carbureted Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge just far enough to free it from the fuel tank. Disconnect the two sending unit connectors. Feed the conduit and two wires up through the tube while removing the gauge. Remove and discard the fuel gauge. For Fuel-Injected Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge to free it from the fuel tank. Feed the conduit and three wires up through the tube while removing the gauge. Remove and discard the fuel gauge. 5. Remove and discard the rubber gasket. INSTALLATION For Kit Numbers 75084-04B or 75237-03B 1. See Figure 2. Assemble the new gasket (3) to the LED fuel gauge (1) from the kit. Install the gasket so the flat side contacts the edge of the gauge. 2. See Figure 1. Use three of the Phillips-head screws and washers from the kit to connect the wires as follows: Fasten the Orange wire (1) ring terminal to the gauge connection marked “12V and “O” with a screw and washer. Fasten the Black wire (2) ring terminal to the connection marked “GND” and “BK” with a screw and washer. Fasten the Yellow/White wire (3) ring terminal to the connection marked “Y/W” with a screw and washer. 3. See Figure 2. While carefully lowering the fuel gauge, feed the wire harness (2) down into the drain tube until the three short (Orange, Black, Yellow/White) wires exit the hole at the bottom of the fuel tank. Gently pull the wires to remove slack while installing the gauge to the fuel tank. Do not twist the gauge during installation. Hold the gauge firmly and press down until it snaps into place

Incoming search terms:

Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

Incoming search terms:

HARLEY DAVIDSON DYNA SPROCKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1991-1992 Dyna models: Screw (5) 3739A 1993-1995 FXDL, 1995 FXD and FXDS, all 1997-1999 Dyna models: Screw (5) 3730A 1993-1995 FXDWG and all 1996 Dyna models: Screw (5) 3769 1991-2005 Dyna models: Washer (5) 6516HW 2000-2006 Dyna models: Screw, with lock patch (5) 3737A 2006 Dyna models: Screw, with lock patch (5) 3873 2007 and later Dyna models: Screw, with lock patch (5) 3109 The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) Kit Contents There are no Service Parts available with this kit. INSTALLATION NOTES The cotter pin or spring clip for the rear axle nut must be replaced during assembly and is available for purchase from a Harley-Davidson dealer. The five sprocket mounting screws must be replaced when replacing the sprocket. Remove existing sprocket according to service manual instructions. Remove all residual threadlocking agent from fastener holes using an appropriate thread chasing device and compressed air.

Incoming search terms:

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

HARLEY DAVIDSON COMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2011

download
Removing the Old Speedometer NOTE This Instruction Sheet covers several different Harley- Davidson models and years. Make sure you locate and follow the procedures that apply to the motorcycle receiving the new gauge. 1. Apply power to motorcycle and record the odometer reading. 2. Remove the seat according to the procedure in the applicable Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. NOTE Cover the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 3. Remove the instrument console acorn nut (and mounting screw with a flat washer on some models). Lay clean shop towels on the fuel tank. Lift the console from the fuel tank, turn it upside down and lay it on the towels. NOTE If necessary, bend back the flexible metal clip to free the harness conduit from the underside of the console. 4. Unplug the 12-terminal connector (39B) from the back of the speedometer. Depress the external latches and use a rocking motion to separate the pin and socket halves. 5. Remove the back clamp: All models except FXSTD: Gently pry the three latches upward to release the back clamp from the back of the speedometer. FXSTD: Depress the three external legs of the lock ring, then gently pry the three latches upward to release the back clamp from the back of the speedometer. 6. Unscrew the trip-meter reset button, and pull the harness from the clamp (remove the screw if necessary). 7. Lift the console and remove the old speedometer from the console. Discard the old speedometer, but retain the rubber gasket and back clamp for use with the new gauge. NOTE Set the console securely on the towel-covered fuel tank, and take care that it doesn’t fall off during the following opera- tions. 8. Set the console securelyon the fuel tank. Installation and Final Check NOTE Apply window cleaning fluid or mild soapy water to the speedometer gasket as needed to aid installation. 1. Turn the console over, facing upward. 2. Place the speedometer gasket into position around the console speedometer bore. 3. Fit the new gauge into the bore so that it fits snugly against the rubber gasket. Rotate the gauge into approximate visual alignment. The back clamp will complete the alignment. 4. Turn the console over, face down. 5. Install the back clamp

Incoming search terms:

ATK 50MX INSTALLATION AND ADJUSTMENT TIPS

0

Filed Under (Atk) by admin on 01-11-2010

download
PRELOAD ADJUSTMENT— On some Works shocks a threaded preload is standard. This allows the adjustment of the ride height of the motorcycle. The preload is changed by turning a threaded nut down towards the spring (higher ride height) or up away from the spring (lower ride height). The nut is a right-hand thread. CHECKING RIDE HEIGHT— 1. With the bike unloaded on the side stand and the shock fully extended, have an assistant measure from a point at the axle (center point) to a point on the frame, fender or bodywork directly above it. Record this measurement. 2. With the bike off the stand and the rider in the seat, bounce on the suspension and let the bike settle. Have the assistant measure from the same two points. Subtract the second measurement from the first. HM CRX50 / BAJA & ATK 50MX INSTALLATION AND ADJUSTMENT TIPS Continued on next page. #HM50 – 5/27/99 #HM50 – 5/27/99 To Front Valve Mounting channel Spacer Flange Shock eye Top View of Shock Mount Fig. 1 Top view of upper shock mount. The flange on the shock bushing must face toward the spacer. The valve should point toward the front of the bike Fig. 1 Top view of upper shock mount. The flange on the shock bushing must face toward the spacer. The valve should point toward the front of the bike 3. The amount of settle, or “sag” is a function of the wheel travel. It should only be between 1/4 and 1/3 of the total travel. 4. If the difference is less than the minimum, reduce the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. 5. If the difference is more than the maximum, increase the spring preload. Measure the distance again starting with Step 2. Adjust again if necessary. Note: If the ride height is too low, the shock will bottom unnecessarily, resulting in a harsh ride. If the ride height is too high, the shock will “top out” too easily when rebounding from a bump or under hard deceleration. NITROGEN PRESSURES IN EMULSION SHOCKS CAUTION: The pressure in these shocks cannot successfully be checked. Concerns with the gauge volume and the gas volume in the shock body create a situation where you cannot accurately determine what pressure was in the shock. In addition when the pressure is lowered (i.e. checking the pressure) the gas and some of the shock oil escapes into the gauge. It is possible to lose a large percentage of the shock oil by depressing the core of a charged shock to the atmosphere. Please note that in order to check the pressure, some of the gas must escape and fill the gauge assembly. The volume of the gas pocket is about half the size of your thumb, so a very small volume change results in a large pressure drop. Because the gauges’ volumes vary, it is not possible to deduce the actual pressure in the shock prior to attaching the gauge. Therefore it is imperative that any attempt to check pressure be accompanied by the capability of refilling the shock. In other words: If you don’t have a nitrogen source handy, don’t check the pressure! PRESSURIZING EMULSION SHOCKS The pressure setting for Works gas shocks is 250 p.s.i. of dry nitrogen. To pressurize a shock with some residual pressure in it, bring the gauge manifold up to 250 p.s.i. and depress the core with the T-handle. This will either equalize the pressure or refill the shock without transferring oil from the shock into the gauge assembly. The best gauges for this purpose screw on to the valve and incorporate a T-handled core depressor to isolate the shock from the gauge. This allows a leak-free separation once the desired pressure is reached. For simplified operation, an extra valve is provided for the filling apparatus, allowing pressure adjustment with the gauge in place. Works offers a suitable gauge and filling manifold. Most motorcycle shops that deal with dirt bikes can pressurize the shock

Incoming search terms:

2009 GAS GAS TXT PRO TECHNICAL SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Gas Gas) by admin on 28-11-2010

download
ENGINE 2 stroke, single cylinder, direct reed valve crankcase induction. Liquid cooled. 125 cc. engine Cylinder size 124,8 cc. Bore and stroke 54 x 54.5 mm. 200 cc. engine Cylinder size 175,3 cc. Bore and stroke 64 x 54,5 mm. 250 cc. engine Cylinder size 247,7 cc. Bore and stroke 72,5 x 60 mm. 280 cc. engine Cylinder size 272,2 cc. Bore and stroke 76 x 60 mm. 300 cc. engine Cylinder size 294,1 cc. Bore and stroke 79 x 60 mm. Carburettor, diameter of the diffusor 26 Lubrication system Mixture (50:1)(2%) Ignition system Digital magnetic flywheel CDI TRANSMISSION Transmission type 6 gears, Four / Six system by GAS GAS* (Patented). Clutch type Hydraulic command, 1/3 discs, variable progressive with diaphragm system by GAS GAS* (Patented). Driving system By chain Gear ratio 1st. 2,996 (35x27x28/16x24x23) 2nd. 2,571 (36/14) 3th. 2,187 (35/16) 4st. 2,112 (36x23x24/14x28x24) 5st. 1,125 (27/24) 6th. 0,821 (23/28)
-11- Primary reduction ratio 2,777 (75/27) Final reduction ratio 3,818 (42/11) Overall drive ratio 8,704 (6th. gear) Transmission oil Capacity 550 cc. Type 10W40 API SF o SG. FRAME Type Tubular profile made with Cr-Mo. Tyres Front 2,75 x 21″ Trial Rear 4,00 x 18″ Trial tubeless. Suspension Front Adjustable tele-hydraulic fork ø 40 mm. (125 / 200). Adjustable tele-hydraulic fork ø 40 mm with aluminium bars (250 / 280 / 300) Rear Variable progressive system with mono-shock multiadjustable. Suspension stroke Front 177 mm. Rear 164 mm. Front fork oil SAE 5. Front fork oil level ø 40 mm.(125 / 200) 180 mm. air chamber steel bar ø 40 mm. (250 / 280 / 300) 160 mm. air chamber aluminium bar BRAKES Type Disc brake. Disc diameter Front ø185 mm. 4 piston calipers. Rear ø150 mm. 2 piston calipers. DIMENSIONS Overall height 1180 mm. Overall width 820 mm. Seat height 650 mm. Ground clearance 315 mm. Wheelbase 1330 mm. Fuel tank capacity 3,1 liters.

Incoming search terms:

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

Harley-Davidson DYNA Straightshot Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove both front and rear head pipe clamp bolts. 4. Remove the entire exhaust system and set it aside. 5. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips. 6. Remove the rear head pipe clamp bracket from the transmission cover. Remove any studs and bolts necessary and set aside to use when installing the new muffler mounting bar to the transmission housing. Refer to figure 1. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the mounting bar (supplied) to the transmission housing using the stock hardware. Refer to figure 1 . Note: The mounting bracket should mount flatagainst the transmission housing. Some motorcycles use a stud to mount the stock rear head pipe clamp, be sure to remove the stud from the transmission housing and replace it when mounting the bracket, this will insure that the bracket is flat against the housing. 2. Check condition of stock exhaust gaskets. Replace if worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets, part number 17048-98. 3. Install the circlips and flanges from the stock system onto both new head pipes. 4. Slide one pipe clamp (supplied) onto the front head pipe. Position the clamp in the approximate location on the tube where it mounts to the engine. 5. Slide one pipe clamp (supplied) onto the rear head pipe. Position the clamp in the approximate location on the tube where it mounts to the top hole in the mounting bar bracket. Refer to figure 1. 6. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike

Incoming search terms:

Incoming search terms: