how to replace honda shadow pipes

You search Auto repair manual PDF how to replace honda shadow pipes, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace honda shadow pipes Direct Download speed 5282 Kb/s

  how to replace honda shadow pipes Full Version speed 6162 Kb/s



Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

Honda Shadow A.C.E. v. Yamaha V-Star 1100 Middleweight Import Cruiser Shootout

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
You want a big cruiser but you don’t need a large 1500 cc behemoth that weighs close to half-a-ton fully loaded. You want something you can cruise down the boulevard on but you want to be able to handle a corner or two. You want classic styling but you insist on reliability as well. If these are your guidelines, then Honda and Yamaha might have what you’re looking for in the guise of the Honda Shadow American Classic Edition and Yamaha V-Star 1100. Shadow ACE 1100 The ACE and V-Star have a few things in common: Both sport requisite V-twin powerplants (75° for the V-Star and 45° for the ACE) and both possess typical Japanese refinement. Aside from these similarities, the two rides are very different machines. While both machines are shaft driven, the ACE uses the shaft housing as the swingarm. Although this arrangement is effective, it’s a bit lacking style-wise. However, the whitewall tires and the classic fenders and tank help to create a traditional design that turns heads when you’re out and about. The V-Star uses a different approach, utilizing a pivoting sub-frame design with a hidden mono-shock that keeps the lines fluid and consistent with the rest of the bike. Although this beast isn’t equipped with whitewall tires, it still cuts a graceful, glittering profile. The only flaw we noticed was the small headlight that

Incoming search terms:

1998 Honda Shadow Aero Specifications And Review

0

Filed Under (Honda) by admin on 24-11-2010

download
can fix it – let us help. The color combo that would have been featured here, had we not got rained on. As light as the morning precipitation was, a rainsuit seemed silly, and surely jeans and a leather jacket would be enough. However, at the crest of the peninsula, El Nino let his wrath be felt. A full-on downpour of Florida- like proportions dropped from the sky, without the benefit of gulf-stream warmth. Suddenly, wearing geeky-looking Gore-Tex seemed like a very good idea. Riding through six inch deep floodwaters at about 15 mph, the Aero kept a very even keel. The floorboards (first ever on a Honda) kept the feet drier than they would have been otherwise. After a brief stop at a military museum, we headed back to Honda’s HQ for a van ride to lunch at Hollywood’s House of Blues. Detail 101: Witness the huge chrome headlight/speedo assembly, with matching idiot lights set into the triple clamp. We couldn’t form much of a riding impression from our rain-soaked 30 mile jaunt, but we liked what we found. If you’re a big fan of the ACE 750, you’ll be a big fan of the Aero. Although the styling is not ground-breaking, it isn’t a carbon copy of you-know-who (hint: They’re based out of Milwaukee). The detail on the Aero is beautiful, with tasteful chrome accents and well-finished pieces. We hope to get the big 1100 back for a full test against Suzuki’s new Intruder 1500LC, Harley’s new Road King Classic, and all the other cruiser big boys some time this spring, after El Nino goes away … Manufacturer: Honda Model: 1998 Shadow Aero Price (two-tone): $9,995.00 Engine: liquid-cooled 45 degree V-twin, single crank pin Bore and Stroke: 87.5 x 91.4mm Displacement: 1099cc Carburetion: Two 36mm CV Transmission: 5 speed Wheelbase: 66.1 in Seat Height: 28.5 in Fuel Capacity: 4.2 gal with .8 gal reserve Claimed Dry Weight: 623 lbs

Incoming search terms:

HONDA SHADOW AERO 750 STRAIGHTSHOT HS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 03-11-2011

download
Install mounting bracket (stamped 359-P) in the original bracket mounting position, using two 10mm bolts and
one 10mm nut (supplied)(Figure 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark the outside edge of each heat shield to show location of hose clamp mounting clips (Figure 3). 3. Slide flanges onto head pipes and lay head pipes into
heat shields. Loosely install hose clamps by feeding tail end of clamp into heat shield clips (Figure 3). Take note of screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas.
4. Using stock nuts, carefully install head pipes into exhaust ports (Assistance may be required). NOTE: Do not tighten at this time.

HONDA SHADOW ACE TOURER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the pinch clamp bolt on the left hand muffler crossover pipe. (Located on the right of the motorcycle, where both mufflers merge with the head pipes). 2. Remove the two 8mm bolts that mount the left hand muffler to the frame. Drop the muffler down to clear the mounts and pull out from the collector. 3. Remove the right hand frame cover to avoid damaging it. 4. Remove the 8mm nut holding the head pipe flanges to the cylinder heads. Remove the 8mm bolts that mount the right hand muffler to the frame. 5. Remove the remainder of the exhaust system from the motorcycle and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Be sure to check that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 2. Install the chrome exhaust flanges (supplied) over the front and rear head pipes. 3. Install the rear head pipe to the rear cylinder using the stock 8mm acorn nuts. Route the pipe approximately 3/4″ beneath the swingarm, leaving the nuts finger tight at this time. 4. Install the front head pipe to the cylinder head using the stock 8mm acorn nuts. Its routing follows the stock head pipe, leave the nuts finger tight at this time. 5. Your Vance & Hines mufflers use the stock mounting locations and rubber grommets. Remove the steel spacers and rubber grommets from your stock mufflers and install them into Vance & Hines mufflers in the same locations. 6. Slip a chrome muffler clamp onto the inlet end of each muffler. Install the clamp hardware as shown in figure 1 (hardware supplied). Leave them loose at this time. 7 Slide the left hand muffler assembly (stamped H641) onto the rear head pipe approximately two inches. Mount the mufflers to the motorcycle using the stock bolts, in the stock locations. 8. Repeat the above step with the right hand muffler (stamped H640). 9. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edges of the heat shields with the location of the mounting clips that are welded to the back side of the heat shield. Position the right rear heat shield (stamped H226) over the rear head pipe and feed the tail end of the hose clamps into the clips. Be sure that each clamp is engaged into both clips. Repeat this procedure with each heat shield.

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

Honda VT1100C Shadow, Aero, Sabre SPECIFIC-FIT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets TIP: Use soapy water to lubricate the grommets so they will slip into the holes in the bag. The vehicle images in this instruction set may be different than your motorcycle. Continued on next page… 3 Lay a support 7 (with the joint towards the rear of the bag) on the back of a bag. Temporarily put the mounting bolts 8 through the support’s holes and into the plas- tic spacers in the grommets. Place one of the support clips 9 over the center of the lower portion of the support, so the two holes in the clip align with the predrilled holes in the bag. Use the 3/16” screws and nuts from the hardware kit to attach the support clip to the backup plate inside the bag. Place the nuts on the outside of the bag. Do not over- tighten the hardware, as this may cause damage to the saddlebag. Remove the mounting bolts from the support and the plastic spacers

Honda Shadow VT750C Fuel Valve Diaphragm Replacement

0

Filed Under (Honda) by admin on 25-11-2010

download
1. Drain the fuel into an approved container. 2. Remove the fuel tank using the procedure in the Service Manual. However, do not remove the fuel valve from the fuel tank. 3. Remove the four screws, and diaphragm cover. NOTE: The diaphragm cover is under spring pressure. The countermeasure part has a paint mark near the air vent hole. 4. Replace the diaphragm, spring, cover, and screws with new parts included in the kit. Install the new diaphragm with the plastic retainer facing the diaphragm cover. NOTE: Make sure the air vent hole is facing downward towards the ground. 5. Reinstall the fuel tank using the procedures in the Service Manual. 6. Refill the fuel tank

HONDA VT1100 SHADOW EXHAUST SYSTEM Installation Manual

0

Filed Under (Honda) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two header nuts from the exhaust port on both front and rear cylinders. The nuts will be reused during installation. 2. Remove the mounting bolts/nuts located below the lower muffler. Carefully remove the entire system and set it aside. Note: The system is heavy so have someone assist you. 3. Remove the muffler mounting bracket from the frame but save the two bolts for reuse. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Remove the bar bracket from the box. Hold the bar bracket in front of you with the four hole bracket positioned to the right hand side and pointing down. Mount one muffler to the bracket on the left hand side of the bar using two of the 5/16″ bolts (supplied) and leave them loose. Be sure the small end of the muffler is pointing to the right hand side. 3. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. 4. Slide a new flange onto each header tube. Note: The two smaller holes in the header flanges are offset from the large hole. If the small holes do not align with studs at the exhaust port, spin the flange on the pipe one half of a turn and try again. Refer to Figure 1. 5. Place the head pipe into the heat shield, unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Wrap the hose clamp around the head tube and give the screw three to four turns, leaving heat shield loose on the head pipe. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike

HONDA VF750 MAGNA SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the left and right side frame covers to prevent damaging them. 2. Loosen the pinch clamps on the inlet end of all four mufflers, located behind the rear motor mount. 3. Remove the left and right front head pipes. 4. Remove the rear mounting bolt from both muffler assemblies. Carefully slide each muffler assembly off the head pipes and set them aside. 5. Replace the front head pipes. Note : Leave the head pipes loose for later adjustment. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 2. Place the slip-on head tube into the matching heat shield, wrap the hose clamp around the head tube and give the screw three to four turns, leaving heat shield loose on the head tube. Repeat this step with opposite head tube and heat shield. 3. Slide a T-bolt band clamp (supplied) onto the slotted end of each slip-on tube. 4. Slip the slotted end of tube onto the rear head pipes. The shorter of the two slip-on tubes mounts on the right rear head pipe and the longer tube on the left rear head pipe. Tighten the T- bolt clamp until the pipe is snug but so the pipe will still be able to rotate. 5. Install the muffler mounting brackets to the frame using the single hole in the brackets and the stock hardware. The left side mounting bracket (stamped #206 on the bracket) mounts to the outside of the frame, where the stock muffler assembly mounted. The right side bracket (stamped #207) mounts to the inside of the frame, behind the stock muffler mounting point. 6. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (all supplied). Do this to each muffler but leave the clamp loose at this time. 7. To determine the difference between the left, right, upper and lower mufflers refer to the number stamped on the bracket welded to the backside of each muffler. The top right hand muffler is D500, the bottom right hand muffler is D510, the top left hand muffler is D550 and the bottom left hand muffler is D512. Note : The endcap bolts should face down and inward when viewing from the rear (Refer to Figure 1) .

Incoming search terms: