how to replace quadbike coil

You search Auto repair manual PDF how to replace quadbike coil, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace quadbike coil Direct Download speed 5282 Kb/s

  how to replace quadbike coil Full Version speed 6162 Kb/s



Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

HARLEY DAVIDSON DYNA CHROME COIL COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Installation 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Note the position of each spark plug wire in the ignition coil, then disconnect the two wires. 3. If there is an existing coil cover: Remove and discard the coil-cover mounting screws and spacers. Remove and discard the coil cover. If there is not an existing coil cover: Remove and discard the two coil mounting screws. 4. See the Service Parts illustration. Obtain the coil cover bracket (3), two long screws (4) and two spacers (2) from the kit. 5. Insert the screw into one of the holes in the bracket as shown, through a spacer, and into a coil mounting hole. Repeat with the second screw and spacer. 6. Assemble the coil to the electrical caddy with the two screws. Tighten the screws to 50 in-lbs (5.6 Nm). 7. Obtain the new chrome coil cover (1) from the kit. Position the cover over the coil, and fasten to the coil cover bracket with the three chrome screws (6) and washers (7) from the kit. Do not fully tighten the screws at this time. 8. Connect the spark plug wires through the holes in the side of the coil cover onto the correct coil terminals. 9. Adjust the cover to center the spark-plug wire boots in the coil cover holes for best appearance. Tighten the three chrome screws securely 10. Refer to the Service Manual and follow the instructions given to install the maxi-fuse

Incoming search terms:

HARLEY DAVIDSON CHROME SEAT POST REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
REMOVE 2 1 is00000 1. Seat Post 2. Screw Figure 2. Lower Seat Post 1. Refer to Owners Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery negative cable. 3. On motorcycles equipped with oxygen sensors, disconnect the rear sensor connector. 4. See Figure 2. Remove screw (2) and washer from the lower seat post (1) and discard. -J04294 1 of 2 5. Disconnect spark plug wires and primary wire from ignition coil. 6. See Figure 3. Loosen the bracket screws (1). Remove seat post screw (2) and seat post with ignition coil and cover. 7. See Figure 4. Remove coil cover screw (5) and cover (4) from stock seat post (1). 8. Remove ignition coil screws (3) and coil (2) from seat post. 2 1 is04241 1. Bracket Screws 2. Upper Seat Post Screw Figure 3. Upper Seat Post Fasteners 2 5 1 3 4 is04337 1. Seat Post 2. Ignition Coil 3. Coil Screw 4. Coil Cover 5. Coil Cover Screw Figure 4. Install Ignition Coil to Seat Post INSTALL 1. See Figure 4. Install ignition coil (2) to new seat post using screws (3). Tighten ignition coil screws to 10-15 ft-lbs (13.6-20.3 Nm) . 2. Install coil cover (4) to seat post with screw (5) and tighten to 30-40 in-lbs (3.4-4.5 Nm) . 3. See Figure 1. Place seat post (1) in position and attach lower post with screw (2), washers (3) and dome nut (4). Tighten screw (2) to 10-15 ft-lbs (13.6-20.3 Nm) . 4. See Figure 3. Attach upper seat post with screw (2). Tighten screw (2) to 12-15 ft-lbs (16.2-20.3 Nm) . Tighten bracket screws (1) to 12-15 (16.2-20.3 Nm) . 5. Connect primary wire to ignition coil. 6. Connect spark plug wires to ignition coil. The rear cylinder plug wire attaches to the top coil post. Ensure that spark plug wire boots are fastened securely. 7. Connect rear oxygen sensor connector, if equipped. 8. Reconnect battery negative cable

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

HI-4 DUAL FIRE MOTORCYCLE IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Turn ignition switch off and disconnect battery ground cable. 2. Refer to Figure 3. Remove OE ignition module and wire harness (items 1-4). You will disconnect two wires at the coil (15), a wire going to the VOES (Vacuum Operated Electrical Switch) (18), a black ground wire at the ignition module, and the 3 pin plug (20) that connects to the sensor plate (11). Refer to shop manual for locations. 3. Remove ignition cover plates and gasket (items 5- 9). This will require drilling out two rivets. The rivets will later be replaced with two supplied self- threading screws. 4. In order to remove the sensor plate cable, the cable plug (20) must be removed first. Use needle nose pliers to pull the terminals out of the plug. Then pull the cable through the exit hole at the bottom of the timing cover. 5. Note location of sensor plate (11). There is a V notch in the sensor plate used for alignment. When you install the HI-4, you should align the V notch in the same location. This should set the timing close enough to start the engine. Remove and save the two standoffs and washers (10). Remove the sensor plate (11). HI-4 INSTALLATION Refer to Figure 4. The HI-4 requires use of the OE timing rotor P/N 32402-83 (used only on 1985 and newer models). If you have an older model or are not sure, check the rotor (9) for the correct part number. For models prior to 1980, use the supplied 10-32 x ¾”bolt and washer to mount the rotor. 1. Install the HI-4 system in place of the OE breaker or sensor plate. Rotate the HI-4 about 90 degrees to give better access to the cable exit hole. Install the HI-4 first, then push the cable through the hole. On some early models it may be necessary to enlarge the wire harness exit hole in the gear cover. Align the V notch on the HI-4 same as the OE plate you removed. Use the OE standoffs to secure the HI-4. You must use lockwashers under the standoffs for proper clearance between the HI-4 and cover plate. Do not fully tighten the standoffs until the timing has been set. 2. Route the HI-4 wire harness along the frame rails up to the coil. Make sure that harness will not be chafed or burned by exhaust heat. Secure harness with tie wraps. Do not install timing cover. HI-4 HOOKUP Crimp terminals and hardware are supplied for your convenience. Use the ring terminals for coil hookup. Use male-female quick disconnects for connections to the tach and vacuum switch (VOES). Tape up any unused wires. 1. Circuit Breaker Cover Screws (2) 2. Circuit Breaker Cover 3. Circuit Breaker Cover Gasket 4. Breaker Plate Screws (2) 5. Breaker Plate Screw Lockwashers & Washers (2 each) 6. Retainer (1971 to early 1972) 7. Circuit Breaker Cam Bolt 8. Breaker Plate Assembly 9. Breaker Cam 10. Advance Assembly 11. Gear Case Cover 11 10 9 8 7 6 5 4 3 2 1 NOTE: Damage will result if the brown tach wire comes in contact with +12V. Figure 1. Harley-Davidson®OE Points System
9000-4002A REV A 3 2/05 1. Identify switched +12 volt wire and tach wire (if equipped) going to the coil. Refer to your service manual, or reconnect the battery and use a test light or voltmeter. The switched +12 volt wire will be hot when the ignition key is turned on. 2. Refer to Figure 5. Connect the HI-4 red wire and switched +12 volt wire to Coil positive. 3. The HI-4 white wire is not used and should be taped. 4. Connect the HI-4 black wire to the Coil negative terminal. 5. Connect the HI-4 green wire to the vacuum switch (Figure 3, item 18), if used. 6. Connect the HI-4 brown wire to the tach wire, if equipped with tach. Tape up if unused. 7. The HI-4 is grounded via the timing housing; a separate ground connection is not required. 8. Reconnect battery ground cable. Verify proper ground connections to the frame and engine. VOES HOOKUP The OE vacuum switch (VOES) is normally an open circuit. Above 3-5 inch-Hg vacuum, the VOES closes and grounds the vacuum input on the OE ignition module. This increases the total advance generated by the OE ignition module. Vacuum advance improves part throttle 17 16 1. Cover Screws (2) 2. Ignition Timer Cover 3. Ignition Module 4. Timer Plate Screws (2) 5. Washers (2) 6. Screws & Washers (2 each) 7. Shield 8. Sensor 9. Trigger Rotor Bolt 10. Timer Plate 11. Trigger Rotor 12. Advance Assembly 13. Gear Case Cover 14. Ignition Coil 15. Spark Plug Wires (2) 16. Ignition Coil Terminal (FX) 17. Ignition Coil Terminal (FL) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NOTE: Most motorcycle coils do not have terminals marked. Use either terminal for Coil+ (positive) and the other one for Coil- (negative). Warning: The HI-4 (8-1100) Dual Fire ignition will not work with 2 plugs per head, dual coil application. Damage will result if attempted. Use the HI-4 (8-2100) single fire ignition for 2 plugs per head applications

Incoming search terms:

POLINI X1 GENERAL INFORMATION AND SPECIFICATIONS

0

Filed Under (Polini) by admin on 02-12-2010

download
Air cleaner – Clean and reoil daily or after each moto to prevent motor failure and reduced performance. Transmission oil – change after every race, or at end of riding day. Chain – check tension and lubricate before every ride, adjust or replace as needed. Reoil after riding in damp conditions. Clutch – disassemble and clean clutch assembly frequently, every 2-3 races at least. Inspect kickstarter gears at this time. Ignition cover – remove cover and wipe dry after each ride or after washing bike to remove condensation. Piston rings – replace as often as every 3-5 races with expert rider, less often with less aggressive riders. Piston, pin, rod bearing & circlips – replace as often as every 8-10 races with expert rider, less often with less aggressive riders. Coolant – change yearly, make sure there is at least a 50/50 mixture of antifreeze if freezing temperatures are possible. Steering bearings – Check daily for looseness or play. Adjust and regrease as needed. Swingarm – Check often for looseness. Regrease several times a year. Replace bushings if any play is evident. Sprockets – check for worn or curved teeth each time chain is adjusted. Chain roller& wear pads – check roller for free rotation when checking chain. Make sure roller is not bent or damaged. Check chain wear strips on swingarm and chain guide frequently. Replace as needed to prevent chain from damaging motorcycle. Spokes – Check after each race or after each day of riding for looseness or damage. Wheels & tires – check wheels after each race for dents, cracks or other damage. Check tires for cuts, damage or wear. Check tire pressure daily and adjust for riding conditions. Shock – Check shaft area daily for signs of oil leakage or damage. Check swingarm and shock bushings for looseness. Forks – Check forks daily for leaking oil or damage to tubes. Make sure forks are not twisted check for smooth operation. Spark plug – check sparkplug color and condition after each race or end of riding day. Adjust jetting to keep plug from fouling or overheating. Silencer – If bike seems to be getting louder, replace packing and decarbonize inner tube. Expansion pipe – check daily for large dents, damage or leakage. Remove carbon from headpipe when pipe is removed. Have large dents fixed, or any dents within 8″ of the cylinder. Replace o-rings on pipe as needed to maintain a good seal. Footpegs – check daily for proper operation, pegs should spring back into place. Make sure pegs are not bent or overly dull. Handlebars – check bars after any crash for bending. Look for cracks near bar clamps. Replace bars that have been straightened more than 2 or three times, or if bar is badly bent. Aweakened bar can snap suddenly causing injury to rider. Throttle – check throttle for proper operation each time before bike is started. Remove and clean inside of grip and bar as needed. Grips – check grips daily for wear or looseness. Replace as needed. Use grip glue & safety wire to help hold grips in position. Calipers & pads – check pad wear and caliper function daily or after each race. Replace pads and clean calipers as needed. Brake lever – check lever daily for damage or wear. Make sure lever is at proper angle for both seated and standing positions. Leave lever clamp loose enough to allow clamp to rotate during crash rather than breaking lever. Check and adjust freeplay as needed. Brake pedal – Check pedal daily for damage and proper freeplay. Adjust rear caliper as needed. Reeds – Remove and inspect reed block during every ring change. Check reeds for signs of wear, fraying and cracking. Make sure reeds sit flat and seal well. Replace at any sign of wear or damage or at least once a year, more often for expert riders. Nuts & bolts – Check all nuts and bolts regularly. Make sure to check engine mounting bolts and swingarm bolt frequently

Incoming search terms:

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

YAMAHA XS650H/ SH Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 21-11-2010

download
Ignition timing check 1. Ignition timing is checked with a timing light by observing the position of the rotor pointer and the marks stamped on the timing plate. The timing plate is marked as follows. “ll” Firing range for No. 1 (L.H.) “T” Top Dead Center for No. 1, fL.H.1 cylinder 2. Connect the timing light to the left cylinder spark plug lead wire. 3. Start the engine and keep the engine speed as specified. Use a tachometer to check the engine speed. B. PICK-UP COIL ASSEMBLY The method of mounting the pick-up coil assembly is changed for easier service work. Thus, the followings “Pick-up coil assembly removal” and “Pick-up coil assembly reinstallation” should be changed. Pick-up coil assembly removal Remove the pick-up coil securing screws and remove the pick-up coil assembly. Pick-up coil assembly reinstallation Install the pick-up coil assembly on to the stator assembly. _ L 4. Specified engine speed: 1,200 r/min The rotor pointer should be within the limits of ” fl ” on the timing plate. If it exceeds the limits or does not steady, check the timing plate for tight- ness and/or ignition system for damage. NOTE: Ignition timing is not adjustable. C. FUEL LEVEL The carburetor is furnished with a drain screw to provide easy access to service work. Thus, the following “Fuel level measurement” should be added. Fuel level measurement NOTE: Before checking the fuel level, note the follow- ing: 1. Place the motorcycle on a level surface. 2. Adjust the motorcycle position by placing a suitable stand or a garage jack under the engine so that the carburetor is positioned vertically. 1. 2. Connect the level gauge (special tool) or a vinyl pipe of 6 mm (0.24 in) in inside diameter to the float bowl nozzle left or right side carburetor. Set the gauge as shown and loosen the drain screw 3. Start the engine and stop it after a few minutes of run. This procedure is neces- sary to obtain the correct fuel level. NOTE: Make sure the fuel petcock is “ON” or “RES” oosition. 4. Note the fuel level and bring the gauge to the other end of the carburetor line and repeat step 3 above. Note the fuel level again and compare it with the previous gauge reading. They should be equal. If not, place a suitable size of wooden piece or the. alike under the center stand and adjust. 5. Check the fuel level one by one. The level should be in the specified range.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE XL1200S RACE IGNITION SYSTEM Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 26-12-2010

download
Disconnect battery, negative cable first. 2. See Figure 1. Remove seat and locate ignition module. 3. Remove the two nuts that hold the ignition module in place. 4. Unplug the two module connectors and remove module. 5. Plug in new module and secure module in place with nuts removed in step 3. Tighten nuts to 15-21 in-lbs (1.7-2.4 Nm). 6. Disconnect spark plug cables from coil towers, noting their positions for reinstallation on new coil. ® Kit Numbers 32737-98, 32738-98, 32739-98 Figure 1. Ignition Module i01020 1 of 2 NOTE The spark plug cables have numbers printed on them that correspond to numbers adjacent to the coil towers on the coil. 7. See Figure 2. Making note of wiring positions, disconnect primary wire plug from back of coil by gently prying up latch and pulling connector rearward. 8. Remove mounting bolt and remove existing ignition coil. 9. Install new coil with mounting bolt removed in previous step. Tighten bolt to 2-6 ft-lbs (3-8 Nm). 10. Plug in primary wire connector into back of coil. 11. Connect spark plug cables to new ignition coil. 1 WARNING Always connect the positive battery cable first. If the positive cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion resulting in personal injury. 12. Reconnect battery cables, positive cable first. 13. Check engine timing according to procedures in applicable XLH Service Manual.

Incoming search terms:

BMW R1100 – R850R Maintenance Guide

0

Filed Under (BMW) by admin on 27-11-2010

download
R1100 Checklist – Carl Kulow • Check alternator belt (replace 36K miles) • Adjust valves • Spark plugs (replace 12K) • Air filter (replace 12K) • Lube and adjust clutch cable • Lube front shock lower mount • Lube side and center stand • Check brake fluid (replace yearly) • Check brake pads • Check battery acid level • Fuel filter (replace 24K) • Throttle body sync • Oil and filter (replace 6K) • Check transmission fluid level (replace 12K) • Check rear wheel drive fluid level (replace 12K) • Check tires and pressure • Check all nuts and bolts • Check all air and oil hose clamps • Check all lights PARTS – TOOLS Tools Parts Misc. sockets spark plugs compressed air wrenches oil filter anti seize torque wrench air filter carb cleaner hex sockets brake pads rag hex wrenches oil – 4 qt. BMW #10 grease feeler gauges gear oil – 1 1/4 qt. flexible tubing oil filter tool alternator belt (tygon) flashlight fuel filter, o-ring, clamps measuring cylinder crush washers Mityvac -3 small = trans.drain, rear drive fill and drain digital volt meter -1 medium = oil drain heat gun -1 large = trans.fill tire change tools 5 R1100 Maintenance Steps – Carl Kulow Note: This overview section serves only as a step by step reminder for experienced workers. If you are unfamiliar with any procedure you should read the parenthetical reference article or Paul Glaves’ Routine R1100 Service Article! Note to R1100RT and R1100RS Riders: remove the side panels as described in your owners manual “Service and Technical Booklet” except RT: instead of pulling the mirror off as the manual says, you need to hold the back of the mirror (front of bike) with one hand while you hit the front outside corner of the mirror with the palm of your hand thus knocking the mirror off. Check Alternator Belt remove four bolts holding black plastic cover(4mm hex), remove cover, check belt for cracks etc., check belt tension, replace belt every 36K miles, leave cover off for valve adjustment (see Jon Diaz “Alternator Belt Adjustment”)

Incoming search terms: