how to replace shifter bushing on softail deluxe

You search Auto repair manual PDF how to replace shifter bushing on softail deluxe, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace shifter bushing on softail deluxe Direct Download speed 5282 Kb/s

  how to replace shifter bushing on softail deluxe Full Version speed 6162 Kb/s



Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

TRIUMPH ROCKET III HEEL / TOE SHIFTER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Loosen the 10mm nuts at the ends of the shifter linkage rod (notice one end is a left hand thread). Remove the 10mm nut from the shifter arm & disengage the linkage. Remove the shifter pivot bolt using a 8mm hex key wrench. Remove the washer on the threaded side of the shifter pivot bolt. 2. Place one of the wave washers supplied onto the pivot bolt. Place a small amount of grease on the shifter pivot bolt shank and the Heel / Toe shifter pivot hole, insert the pivot bolt into the pivot hole of the toe heel shifter. Use a drop of blue loctite on the shifter pivot bolt threads and install the Heel / Toe shifter, tighten the pivot bolt securely. Check to see that the shifter pivots freely. If the side play is excessive (this is a result of variances in manufacturing tolerances of the stock and supplied components) remove the pivot bolt and install the second wave washer supplied. 3. Unscrew the linkage rod and replace it with the longer rod supplied (NOTE the rod has a left hand thread on one end and right hand threads on the other). Insert the shifter linkage stud into the desired hole in the new shifter being sure the flats on the stud engage the slot on the backside of the bolthole. Install the nut and finger-tighten only at this time. 4. While seated on the motorcycle first find the height setting you prefer for the toe shifter. Using one of the three boltholes for the linkage can set this. You can also gain some adjustment by exposing more or less threads of the new longer shifter linkage rod; however be sue that you have a minimum of 4-5 threads still engaged in the linkage ends. After setting the height, tighten all three 10mm nuts (the two at the ends of the linkage rod and the one which attaches the linkage to the toe/heel shifter) securely. After you have the toe shifter adjusted to your liking you can select the heel shifter height by moving the button head cap screw that secures the toe shifter to the heel shifter (Using a 5/32″ hex key wrench) next to the 10mm linkage nut to any of its three holes

Incoming search terms:

HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

Incoming search terms:

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON DYNA FLOORBOARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Installation SHIFTER ASSEMBLY (LEFT SIDE) 1. Remove highway footrest assembly, if equipped. Discard bracket, plate and mounting hardware. 2. Remove stock footrest assembly. 3. Remove stock (chrome) shift lever. Retain shift lever, peg, bolt and washer. 1 WARNING ® 1 of 5 Kit Number 50601-01 -J01921 2 of 5 Figure 1. Shifter Assembly (Left Side) Item Description Part No. 1 Bolt, 5/16-18 x 5/8 hex HD 2882W 2 Hex cap screw, 5/16-18 x 2.00 (2) 3023 4 Set screw, shaft cover 3231B 6 Assembly,shift lever 33704-01A 7 Assembly,adjustable shifter rod 33719-79B 8 Lever, shifter, machining, polish 33706-01 9 Assembly, shifter plate, polish 33700-01 10 Cover, shifter lever, rubber (2) 34619-85 11 Retainer,shift lever for 1996 to 2000 models 34639-93 Item Description Part No. 11ARetainer bracket, shift lever for 2001 and later models 34639-01 12 Cover, shifter shaft 34640-93 13 Washer, wave, overlap type (2) 34641-01 17 Socket head cap screw 4740A 25 Washer, 5/16″ (2) 6016 28 Washer. 5/16″ 6702 30 Nut, hex, locking, 5/16-18 7710W 32 Acorn nut, 5/16-24 7736 33 Hex jam nut, 5/16-24 7744 30 11 1 12 7 32 28 6 13 9 25 2 17 25 2 10 8 i03110.eps 33 4 11A ’96-2000 models 2001 and later models 4. See Figure 1. 1996 to 2000 models. Bolt shifter lever shaft retainer bracket (11) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 2001 and later models. Bolt shifter lever shaft retainer bracket (11A) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 5. Loosen the left rear crankcase bolt (at bottom of cylinder) and slide the slotted end of shifter lever shaft retainer bracket (11) onto the bolt, but beneath the washer. Tighten crankcase stud to 15-17 ft-lbs (20-23 Nm). 6. Place chrome cover (12) on shifter lever shaft (at primary case) and secure with set screw (5). NOTE Small wave washer (13) goes between foot shifter and bracket. 7. See Figure 1. Place small wave washer (13) on shifter lever (6) shaft. Coat shaft with Loctite Anti-seize and slide into bracket. 8. Install foot shift bracket (9) using screws (2). Tighten screws to 25-30 ft-lbs (34-41 Nm). 9. Place shifter rod (2) and washers (25) in position. Use short stud on shifter rod to secure shifter rod at the transmission end. Use Loctite 242 (blue) on stud before installing. 10. Install acorn nut (32) and washer (28) at foot shift end. Use Loctite 242 (blue) on acorn nut before installing

Incoming search terms:

HARLEY DAVIDSON SOFTAIL EXTENDED REACH CONTROLS KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
PREPARE THE MOTORCYCLE 1. For models equipped with saddlebags: Remove the saddlebags following the instructions in the appropriate Service Manual. 2. Remove the seat following the directions in the Owner’s Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect the negative battery cable. 4. Secure motorcycle in upright position. NOTE This kit is not compatible with engine guards. 5. If the engine guard is present, remove and discard it. LEFT SIDE Component Removal 1 3 4 2 7 5 6 8 2 is05048 1. Pretzel clip 2. Bushing (2) 3. Screw (6) 4. Jiffy stand bracket 5. Bumper 6. Jiffy stand leg 7. Clevis pin 8. Spring Figure 1. Jiffy Stand 1 2 3 5 4 is05053 1. Jam nut 2. Shifter rod end 3. Acorn nut 4. Shifter rod 5. Shifter arm Figure 2. Shifter Linkage 1. For HDI Vehicles: Remove the left side foot control support, and jiffy stand sensor, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. For all other models: Remove the left side foot control support, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. NOTE Two bearing sleeves will remain inside the footrest bracket. The extended controls bracket from the kit will include two sleeves pressed into the bore of the shift lever arm support. 2. Remove rod ends and jam nuts from the shifter rod. Save the rod ends and jam nuts for installation. Component Installation 1. See Figure 9. Select shifter mounting assembly (6), O- rings (5), nylon washer (4) and the shift rod (1) from the kit. 2. Install the shift arm and new O-rings in the bracket. 3. Apply LOCTITE 243 Threadlocker and Sealant to the three mounting screws and mount the shifter bracket with shift arm to the frame. Tighten the mounting screws to 25-30 ft-lbs (33.9-40.7 Nm)

harley- davidson DYNA BLACK FORWARD CONTROL KIT installation Manual

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
1. Disconnect battery cable, negative (-) cable first. 2. Remove the left side rider footrest assembly. Save the footrest and fasteners for installation. Discard the remaining hardware. 3. From the kit, press hole plugs (8) into the screw holes on the frame where the stock footrest assembly was mounted. 4. Remove plugs from forward control frame mount (I) and discard. 5. Remove the foot shifter lever (A) and shifter peg (D). Discard the old foot shifter lever (A). Save the foot shifter lever hardware and shifter peg (D) for future use. 6. See Figure 2. Remove the primary chaincase cover (6) and primary chaincase housing (1). Refer to your model motorcycles Service Manual for removal procedures. NOTE See Figure 1. Before removing the gear shifter lever (1) ((H) in Table 1), it is necessary to mark the correct orientation of the lever. Using a marking tool, draw a location marking (4) on the end of the splined shaft (2) across from the casting split (3). This will allow the new gear shifter lever to be installed in the same orientation as the old lever. 5 3 4 1 2 is 02083 1. Gear shifter lever 2. Splined shaft 3. Casting split 4. Location marking 5. Lever bolt Figure 1. Gear Shifter Lever Orientation 7. After marking the gear shifter lever orientation, loosen the lever bolt (5) and remove the old shifter lever. Discard the old gear shifter lever but keep the lever bolt. From the kit, install the new gear shifter lever onto the splined shaft in the same orientation as the old shifter lever. Tighten the lever bolt to 18-22 ft-lbs (24.4-29.8 Nm)

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

HARLEY DAVIDSON GEAR SHIFTER SHAFT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
Models This kit fits 1982 and later Touring and FL Softail model motorcycles. Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not Sold Separately Gear shifter shaft cover Not Sold Separately Screw, set There are no Service Parts available with this kit. INSTALLATION 1. Remove the stock heel shift lever from the gear shifter shaft. 2. Install the set screw into the gear shifter shaft cover. 3. Install gear shifter shaft cover with installed set screw over the end of the gear shifter shaft. 4. Tighten the set screw until light contact is made with the shaft groove. 5. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw.

2008 Harley Davidson Softail Deluxe Exhaust Installation Supplement to Installation Manua

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Install LH and RH passenger foot peg mount using 3/8×2-1/4″ hex head bolts, 3/8″ SAE flat washers, 3/8″ lock was and 1″ spacers between the motorcycl frame and mount. Figure 1 hers e xhaust ter) n’t Cut 6-1/4″ from end Cut 1/2″ from end Figure 2 2. Remove exhaust chrome covers from header pipes. 3. It is not necessary to remove the front cylinder’s front cover. Remove header pipes from cylinder heads. Cut pipes as shown in Figure 2. 4. Replace header pipes Cut cover 5-5/8″ from end – Shown already cut Figure 3 5. Cut top cover as shown in Figure 3. 6. Install supplied extension pipes as shown in Figure 3 using the OE e clamps. (Clamps covered by covers in picture – covers will be installed la Rotate clamps to make sure they don’t interfere with the foot peg mounts. Do tighten clamps yet. 7. Mount exhaust hanger bracket to body frame with (3) supplied vibration mounts. Figure 4. Figure 4 8. Install supplied clamps to ends of mufflers and fit over exhaust extensions. 9. Attach exhaust pipes to hanger bracket with OEM hardware (4 bolts). Apply Red Loctite to OEM bolts. Figure 4. 10. Install all chrome covers 11. Tighten all exhaust clamps. Figure 5 12. Install supplied chrome cover with clamp removed from cut OE chrome cover. Supplied cover slips over OE chrome cover. Push cover forward to prevent the body from hitting the cover. Figure 5. 13. Move OE clamp backwards and install 14. Position luggage rack as shown in figure 5. Install luggage rack with OE bolt in the Figure 6 Bracket OE Bolt Clamp Figure 7 Drill ¼” holes bracket using OE bolt and supplied 3/8″ bolt. Figure 6. 7 and drill two ¼” holes in shock tower mount. 1 rear and the supplied ¼” bolts in the front.

Incoming search terms: