how to replace the front brake light switch on a 2000 roadking

You search Auto repair manual PDF how to replace the front brake light switch on a 2000 roadking, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace the front brake light switch on a 2000 roadking Direct Download speed 5282 Kb/s

  how to replace the front brake light switch on a 2000 roadking Full Version speed 6162 Kb/s



Harley-Davidson CHROME HANDLEBAR SWITCH CAP KITS installation and REMOVAL manual

0

Filed Under (Harley Davidson) by admin on 09-03-2012

download
1. Open or remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove left and right-hand switch housing assemblies. Refer to HANDLEBAR SWITCHES in Service Manual. NOTE It is not necessary to disconnect the switch wiring to replace the switch caps. 4. Remove individual switches from switch housing. Refer to SWITCH REPAIR/REPLACEMENT in Service Manual. INSTALLATION Upper Housing Switches 1. For HORN and START switch caps, release torsion spring leg from hole in switch cap tab. Take note of how the spring is installed. The other leg of the spring can remain in the switch bracket hole. 2. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on left side of switch. -J02633 1 of 5 5 2 1 1 3 4 is 01405 1. Switch cap installed correctly 2. Switch cap removal from splined shaft 3. Switch cap removal from pivot pin 4. Switch cap installation onto pivot pin 5. Switch cap installation onto spined shaft Figure 1. Switch Cap Removal and Replacement 3. Pry the switch cap up and away from pivot pin (3) on right side of switch, and remove cap. NOTE Use the clear protective cover film to protect the chrome surface of the switch caps during installation. Remove the film after the installation is complete. 4. See Figure 5. Select proper chrome replacement switch cap from kit. 5. See Figure 1. Place cap onto switch, angling the hole on right side over pivot pin (4) on switch. 6. Carefully press switch cap down onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 7. For HORN and START switch caps, insert torsion spring leg into hole in switch cap tab. 8. Toggle switch back and forth, checking for proper opera- tion. Turn Signal Switches 1. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on switch. 2. Pry the switch cap up and away from pivot pin (3) on switch, and remove cap. 3. Select proper chrome replacement switch cap from kit. Peel a clear protective installation cover from the sheet and place it over the surface of the cap. 4. See Figure 1. Place cap onto switch, angling the hole on top over pivot pin (4) on switch. 5. Carefully press switch cap onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 6. Toggle switch back and forth, checking for proper opera- tion.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL BRAIDED REAR BRAKE LINE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) Drain Brake Fluid 1. Pop off bleeder nipple cap on the rear brake caliper. 2. Install one end of a length of plastic tubing over the caliper bleeder valve. Place the free end of the tubing into a suitable container. 3. Open the bleeder valve about 1/2-turn and pump the brake pedal to drain the brake fluid out of the rear brake system. Do not reuse brake fluid. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) Remove Existing Rear Brake Line 1. Disconnect wiring harness connectors from brake light switch spade terminals. Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 2. Disconnect existing brake line from rear brake caliper and rear brake master cylinder assembly. Save banjo bolts, but discard brake line gaskets. NOTE This kit contains all gaskets needed for replacement. 3. Carefully make note of rear brake line routing and orientation of banjo fittings, then remove existing brake line. Save hex head screw holding brake light switch manifold to tab on frame, but discard brake line and attaching parts. 4. Unthread brake light switch from brake line. Save switch for later use.

Incoming search terms:

HARLEY DAVIDSON XL BRAIDED FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Drain the brake fluid following the instructions in the service manual. Dispose of waste properly. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Disconnect the battery, negative (-) cable first or remove the main fuse. Follow the instructions in the service manual 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Discard sealing washers, but save bolt for installation. 4. Remove bolt and two sealing washers to disconnect brake line fitting from front brake caliper. Discard sealing washers, but save bolt for installation. 5. Carefully make note of brake line routing, then remove existing brake line. NOTE This kit contains clamps and cable straps to either replace the original equipment clamps and cable straps being removed or to add additional brake line support. INSTALLATION Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 1. Position new sealing washers from kit on each side of hydraulic brake fittings (banjo fittings). Small ID washers are for caliper end, large ID washers are for master cylinder end. 2. Insert bolts (removed earlier) through washers and fittings. 3. Hold new braided brake line in position and install bolts into master cylinder and caliper. Tighten only enough to keep banjo fitting in the same orientation as the stock banjo fitting. 4. Verify there is no twist in the brake line. Adjust brake line if necessary. 5. Install clamps from kit by wrapping clamp around braided brake line at each of the clamp mounting locations. Verify clamps are oriented the same as the stock clamps. Install clamp screws but do not tighten. 6. Check entire length of braided brake line: a. Be sure brake line is not twisted. b. Turn handlebars fully-left and right while checking to make sure brake line does not contact any vehicle components. c. Be sure brake line length between clamps is sufficient. 7. Adjust brake line if necessary. 8. Tighten caliper and master cylinder banjo bolts to 20-25 ft-lbs (27-34 Nm) .

Incoming search terms:

Harley-Davidson CHROME FRONT BRAKE CALIPER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
See Figure 1. Refer to FRONT BRAKE CALIPERS: REMOVAL in the Service Manual, and follow the instructions to: a. remove the banjo bolt with bleeder valve (2) and both gaskets (4), and b. detach the front brake line (3) from the caliper. c. Discard the gaskets. For this installation, the banjo bolt (2) can also be discarded. d. Remove the caliper mounting bolts (1). Lift the brake caliper assembly upward to remove it from the brake disc. -J03529 1 of 4
2 5 3 4 1 is04104 1. Mounting bolt (2) 2. Banjo bolt with bleeder valve 3. Brake line 4. Gasket (2) 5. Screen cover Figure 1. Remove Existing Caliper 2. Remove the brake pads from the caliper. Refer to BRAKE PADS AND DISCS: BRAKE PAD REPLACEMENT, FRONT BRAKE CALIPER in the Service Manual. a. Remove the screen cover (5) from the caliper. b. See Figure 2. Note the orientation of the brake pads, and remove the retaining clip (2), pad pin (1) and brake pads from the caliper. Also note the position of the brake pads at removal, so they can be installed back in the same location. 3. Repeat the procedure for the opposite-side caliper. 2 1 is04105 1. Pad pin 2. Retaining clip Figure 2. Front Caliper Pad Pin Pad and Pin Inspection 1. Refer to BRAKE PADS AND DISCS: INSPECTION in the Service Manual, and follow the instructions given to inspect the brake pads. If any front brake pad is worn to 0.5 mm (0.020 inch) or less above the backing plate, replace all four front pads. 2. Inspect the brake disc thickness, lateral runout and warpage. If necessary, follow the instructions in the Service Manual under FRONT WHEEL to replace the discs. Chrome Caliper Installation 1. See Figure 3. Obtain the correct-side new chrome caliper assembly from the kit. Remove the screen cover (5), retaining clip and pad pin (4) from the caliper. NOTE Do not remove the shipping plug protecting the brake line threaded hole until ready to install the brake line. 2. Place the caliper over the brake disc with the brake line threaded hole (protected by a shipping plug) facing upward. 3. See Figure 1. Obtain two of the brake caliper mounting bolts (1), removed earlier. Loosely install both bolts through the front fork and into the chrome caliper. Alternately tighten the mounting bolts to 38.0-51.5 Nm (28-38 ft-lbs) . 4. Install the brake pads removed earlier or, if necessary, new brake pads into the caliper. 5. See Figure 2. Install the new pad pin (1) through the inner and outer brake pads. Tighten to 8.5-11.5 Nm (75-100 in- lbs ) . 6. Install the new retaining clip (2) onto the pad pin. NOTE Ensure that the screen cover is oriented with the single tab end up, and the double tab end down. 7. See Figure 1. Install the new screen cover (5) onto the caliper.

Incoming search terms:

HARLEY DAVIDSON VRSC FUEL TANK SIDE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Note the left and right areas on frame where the covers will be installed. Using a 50/50 mixture of isopropyl alcohol and water, thoroughly clean the frame tubes surrounding the fuel cell on the left and right sides. Let dry completely. 2. Unlock and open seat. NOTE Loosening the ignition/light switch screw (in the following step) will allow much easier alignment of the ignition/light switch cover and ignition/light switch during installation. 3. See Figure 1. At area inside of frame rail just above the ignition/light switch housing, loosen the ignition/light switch screw just enough to allow the ignition/switch switch to move slightly from side to side and up and down. Do not completely remove screw 4. See Figure 4. Obtain the right side cover bracket (ignition/light switch side) from kit. 5. Remove the strips protecting the adhesive at all of the raised sections on the cover. 1 2 is 02045 1. Ignition/Light Switch Screw 2. Ignition/Light Switch Figure 1. Loosen Ignition Switch Assembly 6. See Figure 2. Carefully align the right side cover between the three frame tubes. Beginning with the left portion of the cover, press the cover between the upper and lower frame tubes until the raised portions of cover (with adhesive) begin to snap into place. While carefully aligning the right portion of the cover, move the ignition/light switch as necessary until centered within hole in cover, then firmly press into place. Adjust ignition/light switch until the switch is centered within cover. Make sure all raised locations (with adhesive) are firmly contacting the upper and lower frame tubes and that cushion rests against front vertical frame tube. 7. See Figure 1. Tighten the ignition switch screw to 6-10 Nm (53-88 in-lbs ) . NOTE The right side (ignition/light) switch cover surface can be damaged by the key fob (from vibration) when the key is in the ignition and the bike is running. You can either remove the key fob so it does not damage the cover surface, or you can install the plastic clear sheet (included in kit) onto the side cover for protection. 8. If desired, perform the following to install the plastic clear cover onto the ignition/light switch cover. a. Obtain the plastic (rhino) sheet and hold up to the switch cover to determine proper orientation and spacing. b. Carefully peel the adhesive backing from the plastic sheet and position onto the cover. Use a wet sponge, and working out from the center, rub out any bubbles or overlapped areas under the sheet. Allow to dry completely.

Incoming search terms:

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

Skyteam ST 125 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Skyteam) by admin on 24-11-2010

download
BRAKES This motorcycle has a hydraulic brake system of front and rear . Brakes are items of personal safety and should be properly adjusted. Remember to check periodically the brake system and these checks should be conducted by qualified Jincheng dealer. Do not use the remained brake fluid from on a unsealed container, never reuse the brake fluid remained in the last repairing, because the used brake fluid may absorb the water from the air. Use DOT 4 brake fluid from a sealed container. Do not spill out the brake fluid, when the brake fluid is glued to the paint, plastic and rubber material, a chemical reaction shall take place, causing the damage. (1)lower level mark Front brake Rear brake BRAKE FLUID (1) (2) (3) (1) (1)Brake fluid cap (2)Max. fluid level mark (3)Min. fluid level mark Brake fluid may cause irritation. Avoid contact with skin or eyes. In case of contact, flush thoroughly with water and call a doctor if your eyes were exposed NOTICE WARINING * 9 BRAKE LINING The main points for checking the front brake lining are to see whether the lining wear is out of the range. Replace the brake lining wear is out of the range. Replace the brake lining if the lining wear is beyond the brake wear limit mark. FRONT BRAKE FLUID LEVEL Check that the fluid level is above the lower level mark(1) with the motorcycle in an upright position. Brake fluid must be added to the reservoir when ever the fluid level begins to reach the lower level mark(1). Fill the reservoir up to upper level mark. REAR BRAKE FLUID LEVEL There are two marks in rear brake fluid cap,keep the fluid lever between the Max. fluid level mark (2) and the Min. fluid level mark (3) always. Check if it is short of brake fluid, check the hose and other components for corrosion or cracks. limit mark Brake Pad Front brake Rear brake If the brake system or brake linings have to be repaired, we suggest that these repair should be performed by your authorized SKYTEAM dealer. SKYTEAM dealer knows your motorcycle best and is dedicated to your complete satisfaction

Incoming search terms:

Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

Kymco People 125/ 150 FRONT WHEEL/ FRONT BRAKE/ FRONT SUSPENSION

0

Filed Under (Kymco) by admin on 12-12-2010

download
SERVICE INFORMATION GENERAL INSTRUCTIONS Remove the motorcycle frame covers before removing the front wheel. Jack the motorcycle front wheel off the ground and be careful to prevent the motorcycle from falling down. During servicing, keep oil or grease off the brake drum and brake linings. Contaminated brake disk or brake pads reduce stopping power. Clean the contaminated brake disk with high-performance brake degreaser and replace the brake pads. Do not use brake fluid for cleaning. Bleed air from the brake system if the brake system is removed or the brake is soft. Do not allow any foreign matters to enter the brake system when filling it with brake fluid. Brake fluid will damage painted surfaces and plastic parts. When servicing the brake system, use shop towels to cover and protect rubber, plastic parts and coated surfaces. Wipe off any spilled brake fluid with a clean shop towel. Inspect the brake system before riding. SPECIFICATIONS Item Standard (mm) Service Limit (mm) Axle shaft runout ─ 0.2 Radial ─ 2.0 Axial ─ 2.0 Front brake lining thickness 5.5 2.75 Front shock absorber spring free length 260 252 Brake disk thickness 3.2_3.5 3.0 Brake disk runout ─ 0.25 Brake master cylinder I.D. 12.700_12.74312.75 Brake master cylinder piston O.D. 12.657_12.68412.64 Brake caliper piston O.D. 33.910_33.93433.901 Brake caliper cylinder I.D.

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

Incoming search terms: