how to replace the starter in a 2004 honda shadow sabre motorcycle

You search Auto repair manual PDF how to replace the starter in a 2004 honda shadow sabre motorcycle, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace the starter in a 2004 honda shadow sabre motorcycle Direct Download speed 5282 Kb/s

  how to replace the starter in a 2004 honda shadow sabre motorcycle Full Version speed 6162 Kb/s



Lilac LS-18 Motorcycle Maintenance Standards

0

Filed Under (Lilac) by admin on 25-11-2010

download
CYLINDER AND CYLINDER HEAD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Cylinder Bore 54 -0.01 54.1 Boring After boring honing should be performed Ovality 0.01 0.05 Boring After boring honing should be performed Taper 0.01 0.05 Boring After boring honing should be performed Oversize 0.25 steps 55 max. Do R and L cylinders at same time / 4 steps Valve Seat Width 0.8 – 1.0 1.3 Adjust Use a cutter Angle 45∞ Combustion Chamber Volume 18.2cc -0.5cc Remove carbon if heavy accumulation Compression Ratio 7.8:1 Head Gasket Thickness 1.0 Cylinder Head Nut Torque 3.0 kg/m (22 ft.-lb.) Out standard Adjust 8mm nut Intake and Exhaust Ports Port Wall SurfaceMust be smooth Remove carbon Intake and Exh. Valve GuidesOD 12 +0.09 +0.1 ID 7 +0.01 -0.0 7.06 Exchange Intake Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Exhaust Valve Stem Diameter 7 -0.02 -0.03 6.9 Exchange Head Thickness 1 0.7 Exchange Intake and Exhaust Valve Seat Face Width Range 0.8~1.0 1.3 Use valve seat cutter Intake Valve Guide Clearance 0.02~0.04 0.08 Replace valve or guide Exhaust Valve Guide Clearance 0.06~0.08 0.12 Replace valve or guide Valve Spring (Large) Installed Load 10.2 kg 8.7 kg Replace Fitted length 31.5 Free Length 36.5 34.7 Replace Tilt 1.5/100 3/100 Replace Valve Spring (Small) Installed Load 5.48 kg 4.65 kg Replace Fitted length 29.5 Page 4 of 10 Free Length 33.5 31.8 Replace Tilt 1.5/100 3/100 Replace Rocker Arm ID 12 +0.00 +0.02112.07 Replace Rocker Shaft OD 12 -0.06 -0.024 11.92 Replace Arm and Shaft Clearance 0.045~0.006 0.10 Replace arm or shaft Tappet Clearance 0.05 Out standard Adjust Measure cold at TDC Rocker Arm Ball Surface 1.8îR -0.006 -0.024 Replace if severe wear Pushrod Bend 0.1 0.5 Straighten Over 100mm (2) CRANKSHAFT, PISTON AND CONROD MAINTENANCE ITEM STANDARD REPAIR LIMIT METHOD REMARKS Piston OD @ Top 53.65 -0.02 Max Diameter 53.95 -0.015 53.85 Replace Ovality 0.1 Piston and Cylinder Clearance 0.04~0.05 0.15 Replace Piston Ring Groove Clearance 0.03~0.07 0.10 Replace Piston Oversize Step 0.25 4 steps Top Ring and 2nd Ring Thickness 2 -0.01 -0.03 1.92 Replace Width 2.5 -0.01 0.55kg Tension 0.85 – 1.15kg 1 Replace End Gap 0.15 – 0.35 Replace Oil Ring Thickness 3.2 -0.01 -0.03 3.12 Replace Width 2.5 -0.1 Tension 1.0~1.3kg 0.65kg Replace End Gap 0.15~0.35 1 Replace Ring Gap Position 120∞ 3 equal spacesOut standard Adjust Avoid Piston Pin Axis Ring Oversizes 0.25 steps 4 steps Piston Pin OD 15 -0.0 +0.006 14.95 Replace Pin Hole in Piston ID 15 +0.012 -0.015.05 Replace Pin and Piston Clearance -0.006 ~ +0.012 0.06 Replace Hand push fit piston at 100∞C Conrod Small End Bush ID 15+0.027+0.016 15.07 Replace bush Conrod and Piston Pin Clearance 0.01~0.027 0.07 Replace Crankpin OD 24.94 +0.0+0.0124.90 Replace Crankpin Roller OD 5 (+0.001+0.003) Refer to conrod ID Replace 3Sizes; 52 per assembly for selective fit 5 (+0.0 -0.002) 5 (-0.003 -0.005) Conrod ID 34.95+0.03+0.02435.02 Axial Play 0.2~0.4 0.5 Adjust Radial Play 0.026~0.036 0.06 Replace

Incoming search terms:

Honda VT1100C Shadow, Aero, Sabre SPECIFIC-FIT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets TIP: Use soapy water to lubricate the grommets so they will slip into the holes in the bag. The vehicle images in this instruction set may be different than your motorcycle. Continued on next page… 3 Lay a support 7 (with the joint towards the rear of the bag) on the back of a bag. Temporarily put the mounting bolts 8 through the support’s holes and into the plas- tic spacers in the grommets. Place one of the support clips 9 over the center of the lower portion of the support, so the two holes in the clip align with the predrilled holes in the bag. Use the 3/16” screws and nuts from the hardware kit to attach the support clip to the backup plate inside the bag. Place the nuts on the outside of the bag. Do not over- tighten the hardware, as this may cause damage to the saddlebag. Remove the mounting bolts from the support and the plastic spacers

Incoming search terms:

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

HONDA 2002-2004 GL1800/A Linked Braking System (LBS) Proportional Control Valve (PCV) Leakage

0

Filed Under (Honda) by admin on 25-11-2010

download
1. Pump the rear brake pedal four times. •If the brake pedal feels spongy, bleed the brake system per the Service Manual. After verifying proper brake system operation, proceed to step 2 below. •If the brake pedal does not feel spongy, proceed to step 2 below. 2. Place the motorcycle on its side stand, with the handlebars in the full left position . Lock the handlebars. 3. Place a scissor jack directly under the left front brake caliper as shown in the illustration. To avoid damage to the caliper, place a protective piece of rubber (such as a piece of inner tube) between the caliper and the jack. Wind up the jack until the front wheel is approximately 15 mm off the ground. 4. Measure the distance from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). Record this measurement . • If the measured length is 30.3 mm, replace the PCV per the Service Manual. (This length indicates the unit’s secondary master cylinder is fully stroked, which means there is no hydraulic brake pressure acting on the PCV.) After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. •If the measured length is longer than 30.3 mm , proceed to step 5 below. • INSPECTION/REPAIR PROCEDURE Record this measurement. Pump the rear brake pedal four times.
GL1800/A #16 ©2005 American Honda Motor Co., Inc. – All Rights Reserved 3 of 6 FEBRUARY 2005 5. Wait 30 minutes. Do not disturb the motorcycle in any way during this time. 6. Measure the distance again from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). •If the measurement has decreased more than 1 mm from the measurement you recorded, proceed to step 7 below. •If the measurement is within 1 mm of the measurement you recorded, the PCV is OK. Proceed to the IDENTIFICATION section of this Service Bulletin. 7. Check the PCV for leakage. • If the PCV is leaking , replace the PCV per the Service Manual. After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. • If the PCV is not leaking , you must diagnose the brake system problem before proceeding. After you have diagnosed and repaired the brake system, proceed to the IDENTIFICATION section of this Service Bulletin. NOTE: Any brake system problem not related to the PCV that is found while performing this Service Bulletin is not covered by this Safety Recall. If the motorcycle’s original factory warranty is still in effect or under HPP, file a normal warranty claim. If the unit is outside its factory warranty period or HPP coverage, contact TechLine for goodwill consideration. 8. Verify proper front and rear brake operation by pumping the front brake lever and rear brake pedal before riding the motorcycle

HONDA CT110 SERIES MOTORCYCLE Cold engine Starting Procedure

0

Filed Under (Honda) by admin on 15-11-2011

download
Prime the engine before starting by cranking the engine several times with the kick starter. The ignition switch should be OFF, the choke lever Fully ON (A) and the throttle opened slightly. Flooded Engine If the engine fails to start after several repeated attempts, it may have become flooded with excess fuel. To clear the engine, turn off the engine stop switch and lower the choke lever to Fully OFF (B). Open the throttle fully and crank the engine several times with the kick starter. Turn the engine stop switch to RUN and open the throttle slightly; start the engine using the kick starter When service is required, remember that your authorized Honda dealer knows your motorcycle best and is fully equipped to maintain and repair it. The scheduled maintenance may also be performed by a qualified service facility that normally does this kind of work; or you may perform most of the work yourself it you are mechanically qualified and have the proper tools
and service data. • These instructions are based on the assumption that the motorcycle will be used exclusively for
its designed purpose. Sustained high speed operation, or operation in unusually wet or dusty conditions, will require more frequent service than specified in the MAINTENANCE SCHEDULE. Consult your authorized Honda dealer for ecommendations applicable to you individual needs
and use

2004 Vengeance MOTORCYCLE OWNERS MANUAL

0

Filed Under (Vengeance) by admin on 21-11-2010

download
Vengeance Warrior • Vengeance Raider • Vengeance Vertebreaker • Vengeance Striker • Vengeance Vendetta • Vengeance Vindicator Shifting Gears Starting off and changing gears requires coordination of the clutch and throttle and gearshift lever. If you don’t do things right, the amount of control you have over the bike is lessened. To start off, pull in the clutch, shift into first gear, roll on the throttle a little, and ease out the clutch. You will become familiar with the friction zone (that’s where the clutch begins to take hold and move the bike), and you add a bit more throttle. You don’t want to stall the engine, nor do you want to over-rev it. There’s a sweet spot in there; find it. Shift while traveling in a straight line. Shifting in a curve is not good practice, and something to be avoided. Become familiar with the sound of your engine, so you can tell when you should shift without looking at your instruments. When you downshift to a lower gear, you should (in one swift, smooth movement) be able to squeeze the clutch, rev the engine a little to let it catch the lower gear smoothly, and shift down. When you come to a stop in traffic, leave the bike in first gear with the clutch disengaged (just in case you want to accelerate out of there in a hurry). Who knows what may be coming up behind you. Braking Don’t ever forget: The front brake on your motorcycle can supply as much as 70 percent or more of your stopping power. The single most important thing you can learn about braking is to use that front brake every single time you want to slow down. Always apply both the front and the rear brakes at the same time. If necessary, apply them hard, but not so hard that you lock up either wheel. A locked wheel, as well as causing the bike to skid, results in downright inefficient braking. Turning When you are riding along the road, you lean a motorcycle into a turn. Learning to lean is an essential part of riding a motorcycle. It is a normal function of the bike when you are changing its path of travel – and quite different from turning the steering wheel of your car. To get the motorcycle to lean in a normal turn, press the handlebar in the direction of the turn and maintain slight pressure on that handlebar to take you smoothly through that particular turn. In other words: press right to go right; press left to go left. Your instincts to keep the motorcycle on a smooth path while keeping it from falling over usually take care of this without you even noticing it. (Demonstrate to yourself how a motorcycle moves by pressing a handlebar slightly while traveling in a straight line. The motorcycle will move in the direction of the handlebar you pushed.)

HONDA 1100 ACE, AERO AND SABRE CENTERSTAND INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-12-2010

download
Relocation of Regulator. Laying under the right side of the motorcycle, locate the voltage regulator. (finned aluminum box-approximately 3″x 4″) Note: See photo #1 – regulator already relocated. Remove the (2) 10 mm bolts attaching the regulator to the frame. Attach the bracket supplied to the regulator as shown. Using the original bolts, attach the regulator and bracket assembly to the frame as shown in photo #1 using the two 10 mm bolts supplied. Clamping Centerstand to Frame . Notice the centerstand is shipped with (2) white plastic washers. Note: See photo #2-A These are in place to overcome the spring tension or lock the stand in place and allow you to pivot the lower stand down partially to make installation easier. Pivot the upper stand about half way from the retracted to the extended (down) position. Note: This will require some force. If the stand will not stay in the position you can further tighten the two 9/16″ pivot nuts. Remove the bolts from the four band clamps. Wrap the (2) small clamps around the small upper frame tube and start the bolts so that the bolt will be at the bottom of the tube and the wrench head facing towards the rear of the motorcycle. Note: See photo #2. Center the stand on the frame from side to side so as to gain even clearance between the feet on the centerstand and the rear tire when the stand is in the retracted position. Holding the larger cradle up against the frame, tighten the (2) small clamps enough to hold the centerstand in place. Install one of the large clamps as shown in photo #3-A. Install the 2nd large clamp as shown in photo #2-C. Again retract the stand and check that the feet have even amounts of space from the side of the rear tire. Tighten the flour clamps securely 5-7 ft. lbs. Next remove the (2) 9/16″ pivot nuts and the white plastic washers as shown in photo #2-A. Re-install and tighten the 9/16″ pivot nuts securely 8-12 ft lbs. With the stand in the retracted position-adjust the stop bolt and lock nut, see photo #3-B, so that the stand is parallel with the ground and does not come in contact with any parts of the motorcycle. Using your new centerstand . To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail or grab under the bottom of the seat. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now put all of your weight onto the centerstand pedal (stand on it). Pull up and back on the grab rail or seat using a rocking motion to rock the motorcycle up onto the stand. Remember it is a matter of using your body weight and leverage not lifting!

Incoming search terms:

HONDA 1100 ACE, AERO AND SABRE CENTERSTAND Page 1 INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 07-11-2011

download
Using your new centerstand. To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail or grab under the bottom of the seat. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now put all of your weight onto the centerstand pedal (stand on it). Pull up and back on the grab rail or seat using a rocking motion to rock the motorcycle up onto the stand. Remember it is a matter of using your body weight and leverage not lifting!
Getting the Bike Down off the Centerstand: While holding the left handle bar and saddlebag rail or seat, firmly rock the motorcycle off the stand. You can also rock it off while sitting on the motorcycle

KTM Starter Gear Maintenance Instructions

0

Filed Under (KTM) by admin on 26-11-2010

download
Checking the electric starter motor for wear -Check Bendix 1 for smooth operation and signs of wear. -Check the sprocket of the electric starter for wear and radial clearance. -Replace O-ring 2 of the electric starter. -Replace gasket 3 . -Check starter idler gear 4 for smooth operation and wear, check that the bearing bushings are seated firmly. Electric starter motor – checking for and adjusting play -Mount the electric starter and the starter idler gear. -Mount the tighten cover 5 . -Move starter idler gear 4 back and forth in the direction of rotation, the maximum play may not exceed half the width of a tooth. -If play is larger, cover 5 must be removed and as many shims 6 with a thickness of 0.10 mm as necessary must be added to eliminate all play. Then remove one shim again. -Check the play again; the maximum play may not exceed more than half of the width of a tooth. 1 2 3 4 5 4 5 6

Incoming search terms:

Incoming search terms: