how to take apart primary

You search Auto repair manual PDF how to take apart primary, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to take apart primary Direct Download speed 5282 Kb/s

  how to take apart primary Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME INNER PRIMARY HOUSING INSTALLATION INSTRUCTION

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not sold separately Chrome Inner Primary Housing 786A Sealing fastener (5) INSTALLATION NOTES Whenever the sealing fasteners are loosened or removed, they must be replaced. Always replace using Harley-Davidson® Original Equipment sealing fasteners part 786A. Do not use part 786. The primary housing included in this kit installs in the same manner as the stock inner primary housing with the following exception: Use the five sealing fasteners included with this kit. Install and tighten fasteners to the torque specified below. For 2006 Dyna model motorcycles: Remove dowel pins from the chrome inner primary housing before attempting installation. Using a pair of pliers or vice grips, remove the dowel pins by carefully twisting and pulling on the pins. Be careful not to scratch or mar the chrome or sealing surfaces of the chrome inner primary housing. Remove the chain tensioner anchor plate, bolt and screws from the stock inner primary housing after it has been removed, then install it on the chrome inner primary housing. See the appropriate Service Manual for the proper tightening procedure, and torque specifications. 1. See the Drive section of the appropriate Service Manual, and remove the stock inner primary housing. Clean the internal threads in the crankcase and transmission case where the sealing fasteners were removed using a wire brush. Install the chrome inner primary housing as indicated below. Replace the five stock sealing fasteners with the five bolts included in this kit. Put a light coat of primary oil under the head of the sealing fasteners and then tighten to 23-25 ft- lbs (31-34 Nm)

Incoming search terms:

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

Incoming search terms:

HARLEY DAVIDSON SPORTSTER CHROME PRIMARY TRIM COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat and disconnect the negative battery cable at the engine crankcase. Retain all seat mounting hardware. 2. Models with mid foot controls: Remove the two screws retaining the left-side rider footrest and mounting bracket assembly. 3. All models: See Figure 1. Note the installed orientation of the transmission foot shift lever to aid in re-assembly. Use a 1/4 in. hex key to remove the socket head screw (5) holding the shift lever (3 or 4) to the transmission shift lever shaft (1). Remove the lever and rubber washer (2). 4 1 5 3 2 5 is 01929 1. Transmission shift lever shaft 2. Rubber washer 3. Foot shift lever (mid control) 4. Shift lever (forward control) 5. Socket head screw Figure 1. Shift Lever Removal 4 2 3 1 is 01930 Figure 2. Primary Cover Mounting Screw Locations NOTE Remove ONLY the four screws shown. 4. See Figure 2 and Figure 3. Remove and discard the primary cover hex-socket head screws from the four locations shown. 5. Refer to CLUTCH CONTROL: REMOVAL: CLUTCH CABLE-LOWER in the Service Manual to remove the clutch cable at the lower end with these exceptions: •The negative battery cable has already been disconnected, and •On mid-control models, the rider footrest has already been removed. 6. See CLUTCH LEVER AND CLUTCH CABLE-UPPER to remove the clutch cable at the upper end. NOTE Be careful not to scratch the paint on the frame tube when removing the clips. 7. Carefully remove the two vinyl-coated spring steel clips that retain the clutch cable to the frame downtube. 8. Obtain all of the items from the kit. 9. See Figure 2. Insert a chrome screw (3), from the outside, through the hole in location 3 on the chrome trim cover. Place the thinner steel spacer (4) onto the threads of the screw from the inside of the trim cover. 10. Use a 5/32 inch hex key on the screw head, and grip one of the Nylon keeper washers (6) with a pliers. Install the washer onto the screw until several threads extend from the washer, capturing the screw and spacer on the trim cover. 11. Insert the remaining chrome screws, from the outside, through the holes in locations 1, 2 and 4 on the chrome trim cover. Place a thicker steel spacer (5) onto the threads of each screw from the inside of the trim cover. 12. Thread a Nylon keeper washer onto each of the screws as described in Step 10. 13. Position the trim cover over the primary cover with the transmission shift lever shaft extending through the clearance hole (A) in the chrome trim cover. 14. Thread one of the chrome screws into the mating primary cover mounting hole for several threads, taking care not to cross-thread the screw in the hole. 15. Carefully start the remaining screws partially into their mating holes. Continue tightening the screws in turn

HARLEY DAVIDSON CHROME INNER PRIMARY COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
INSTALLATION 1 2 3 is06139 Figure 1. Remove Three Original Equipment Screws As Shown 1. See Figure 1. Remove the stock fasteners as shown in Figure 1. Save screw (3) for reuse. 2. Install the stock fastener in the rear inner cover. Place a locating washer over the fastener with the rounded side facing toward the hole in the primary chain case. 3. Slide the rear inner cover into place and loosely secure it with the stock fastener. 1 is06416 1. Acorn nut Figure 2. Fasten Front And Rear Inner Primary Covers Together 4. See Figure 2. Position the front inner cover over the rear inner cover and make sure that the hole in the front cover fits over the threaded stud in the rear cover. Secure the covers together with the acorn nut installed finger tight. 5. See Figure 3 and Table 1. Place the new 4.25 inch (5) and 1-1/2 inch (4) screws in the front inner primary cover. Place locating washers (6) over the fasteners with the rounded side of the washer facing toward the hole in the primary chain case. 6. Tighten all three screws to 108-120 in-lbs (12.2-13.6 Nm) . 7. Tighten the acorn nut. 8. Push the Allen hole plugs (7) into the four exposed screw heads

HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON PRIMARY COVER CHROME HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the negative (-) battery cable from the battery. Disconnect the positive (+) battery cable from the battery. 2. Replace existing zinc hardware with chrome plated hardware one at a time so the primary chaincase and clutch cover gasket do not need to be replaced. 3. Consult the Service Manual for screw locations and torque values. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Connect the positive (+) battery cable to the battery. Connect the negative (-) battery cable to the battery

HARlEY DAVIDSON AUTOMATIC PRIMARY CHAIN TENSIONER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to the appropriate Service Manual and remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect negative (-) battery cable. 3. Refer to the appropriate Service Manual and remove primary cover. 3 1 2 5 4 is00561 1. Screw (2) 2. Anchor plate 3. Nut and washer 4. Manual tensioner 5. Screw (2) Figure 1. Manual Tensioner: 1985-2000 Models 4. For 1985-2000 model motorcycles, remove manual tensioner and replace the carriage bolt as follows: a. See Figure 1. Remove two screws (5) and nut and washer (3), and remove chain tensioner (4). b. Remove two screws (1) and anchor plate (2). c. Replace the carriage bolt in the anchor plate with the carriage bolt from the kit. d. Apply 2-3 drops of Loctite 262 (red) to the threads of the anchor plate mounting screws (1), then install anchor plate and two screws. Tighten screws to 12- 14 ft-lbs (16-19 Nm) . For 2001 and later model motorcycles, remove manual tensioner as follows: a. See Figure 2. Remove nut and washer (1) and remove chain tensioner (2) Removing the Autotensioner for Service 1. Use a tie wrap and secure the shoe to the base of the autotensioner, without securing it to the autotensioner bracket. This will retain the autotensioner adjustment for reinstallation during service. 2. Remove two autotensioner hex screws, and autotensioner. Resetting the Autotensioner 1. See Figure 5. Compress autotensioner wedge (1) and spring back to the base. 2. Hold wedge in position by inserting a hex wrench or pick tool through the hole in the base of the autotensioner. 3. See Figure 6. Move plastic autotensioner shoe (1) into place as shown. 4. If available, install shipping plate (2) to secure the shoe to the base. If it is not available, secure the shoe to the base with a tie wrap

COMPUFIRE 1084 GEAR SETS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
1. Remove the seat and disconnect the cables at the battery. Remove the ground cable first and then the positive (+) cable. 2. Drain the oil in the outer primary case and remove the outer primary cover following instructions in the Factory Shop manual. 3. Bend the tab on the jackshaft bolt away from the bolt head. Remove the starter pinion gear with the jackshaft bolt, lock plate and washer. 4. Remove the clutch assembly using the procedure found in the Factory Shop manual. 5. Remove the original equipment ring gear from the clutch basket by drilling out the rivets with a 5/16-inch drill bit. Drill through the rivet head and tap the ring gear off the clutch basket using a hammer. 6. Drill out the six holes in the clutch basket with the 5/16-inch drill bit. RING AND STARTER PINION GEAR INSTALLATION 1. Attach the new 84-tooth ring gear to the clutch basket using the six 5/16×24 socket head cap screws supplied. NOTE… The bevel side of the ring gear (identified by the three dots) faces away from the starter motor. Torque the socket head cap screws to 29 ft lbs. 2. Assemble and install the primary drive assembly following the instructions in the factory Shop manual. 3. Install the new 10-tooth pinion gear with the jackshaft bolt, lock plate and thrust washer. Torque the jackshaft bolt to 7 – 9 ft lbs. Bend the lock tab on the lock plate against a flat on the jackshaft bolt head. 4. Measure and adjust the air gap between the ring gear and the pinion gear. See Fig-1 . The correct gap is .075 – .125 inch. If the gap is larger than .125 inch, use the supplied shim washers inside the jackshaft coupler. See Fig-2 . If the air gap is smaller than .075 inch, the jackshaft must be shortened by removing material from the splined end of the shaft. See Fig-3 . 5. Install the outer primary cover following instructions in the Factory Shop manual and refill the primary case with the proper amount of primary oil. 6. Re-install the battery cables in the reverse order they were removed. Re-install the seat

Incoming search terms:

1937-1984 Big Twins BRUTE II EXTREME BELT DRIVES INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-10-2010

download
Remove the outer primary cover. Remove the front pulley, chain, compensator & chain adjuster Remove oil lines to primary and plug or clamp to prevent leakage. Cut the chain oiler hose 3 inches from the oil pump and permanently plug. All belts must be run dry without lubrication of any kind. Therefore, remove all oil from inside the primary covers. The spacer behind the front pulley should be removed prior to installing the belt drive. This spacer may or may not be required to correctly align the pulleys. If a spacer is needed for alignment, various sizes are available from your local Primo Belt Drives dealer (part number PX-1 =package of 6 various sizes). Install the front pulley supplied in the kit. Loop the belt around both pulleys to insure that you have the proper belt for your pulleys, then gently push the unit into place. Use the supplied washer & nut on the motor shaft. Torque the motor nut to 80-100 foot pounds. If installing a PC-1000-Aremove the clutch hub & clutch basket. On tapered shaft models check the fit on the shaft & the fit of the keyway in the hub. Install the key in the mainshaft, making sure it is firmly seated (use of super glue or threadlock in the keyway is helpful to keep the key from sliding out of the keyway during clutch installation). Tighten the clutch hub nut(left-hand thread) to 60-90 foot pounds. 1 After installing and adjusting clutch, track the belt by turning the pulleys. If needed use a straight edge between the front and rear pulleys to check alignment. Improper alignment of the pulleys will result in reduced belt life. Spacing the motor pulley outward will cause the belt to track towards the outer primary cover. If spaced too far out the belt will rub on the inside of the clutch shell. Before installing the primary cover be sure that everything inside clears both the outer and inner covers. In some cases a small amount of metal may need to be removed from one or more of the bosses on the inner or outer primary cover.

HARLEY DAVIDSON SOFTAIL 6 SPEED TRANSMISSION – COMPLETE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 3. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. 4. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. 6. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter. 7. See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. 8. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. 9. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing. 10. Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. 11. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. 12. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. 13. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation

Incoming search terms:

Incoming search terms: