how to take windshield off 2003 road king

You search Auto repair manual PDF how to take windshield off 2003 road king, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to take windshield off 2003 road king Direct Download speed 5282 Kb/s

  how to take windshield off 2003 road king Full Version speed 6162 Kb/s



DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

HARLEY DAVIDSON FLST REPLACEMENT WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. See Figure 1. Remove stock windshield. 2. Remove all hardware that secures mounting brackets to windshield. The nine screws must be removed with a T- 27 TORX® screwdriver. Save all hardware and brackets for installing new windshield. 3. Remove all old tape from brackets and apply new tape (1, 2) from kit onto brackets. Align holes in tape with holes in brackets. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets. Tighten all screws and acorn nuts to 48-60 in-lbs (5.4 to 6.8 Nm) . 5. Install windshield (3) on motorcycle CARE AND CLEANING Polycarbonate windscreens/windshields require proper attention and care to maintain. Failure to maintain polycarbonate properly can result in damage to the windscreen/windshield. (00483d) •Do not use benzene, paint thinner, gasoline or any other type of harsh cleaner on the windscreen/windshield. Doing so will damage the surface. •Do not clean Lexan® polycarbonate in hot sun or high temperature. •Powdered, abrasive or alkaline cleanser will damage the windscreen/windshield. •Never scrape the windshield with a razor blade or other sharp instruments, as permanent damage will result. •Sunlight reflections off of the inside curvature of a windscreen/windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windscreen/windshield to avoid reflections. •Do not use benzene, paint thinner, gasoline or any other cleaning agents on the rubber bushings. Doing so will damage the bushing surfaces. Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a) NOTES Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier. Harley-Davidson Windshield Water Repellent Treatment Part Number 99841-01 is approved for use on Harley-Davidson Lexan windshields

HARLEY DAVIDSON QUICK RELEASE DETACHABLE WINDSHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) NOTE Cover the front fender, headlamp and the front of the fuel tank with clean shop towels to prevent scratching. Make sure the windshield assembly does not contact chrome or painted parts. Damage to the finish could result. Turn Signal Relocation Relocate the turn signals according to instructions included in the Turn Signal Relocation Kit, item 20. Assemble the Clamps to the Windshield 1. See Figure 1. Remove the windshield sub-assembly from the packaging and place face down on a clean, soft surface with the mount brackets facing upward. 2. See the Service Parts illustration. Remove both the clamp and hardware kits from the packaging, and separate similar parts in preparation for assembly. Note that upper and lower clamps are exactly alike. 3. See Figure 2. Assemble the clamp assemblies and hardware stacks. The cupped side of the Belleville (cone) washers must face each other and sandwich the windshield mount brackets at each mount point. Failure to orient washers correctly can reduce the windshield’s ability to break away in a collision, which could result in death or serious injury. 4. See Figure 2. One clamp at a time, with the clamp facing upward and inboard of the windshield bracket (2), tighten the shoulder bolts (1) enough to hold the clamp orientation to the windshield during mounting of the windshield to the bike. The bolts will be fully tightened later. Install the Windshield NOTE Keep front wheel straight to prevent brackets from scratching fuel tank. 1. Make sure all four clamps are in the “open” position, then bring the windshield (with the clamp side away from you) to the front of the bike. 1 WARNING 1 WARNING ® Kit Numbers 58779-05, 57160-05 1 of 3 Figure 1. Windshield Mounting Brackets i07503 Figure 2. Windshield MountingClamp i07504 1 Shoulder bolt 2 Right windshield bracket 3 Cup washer 4 Belleville washers (cupped sides face each other with windshield bracket between)

HARLEY DAVIDSON FLHR/ FLHP WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. Remove stock windshield. 2. Remove all hardware that secures the mounting brackets to the windshield. The nine screws that must be removed require a T-27 TORX® screwdriver. Save all hardware and brackets for installing the new windshield. 3. Remove all old tape from the brackets. Apply tape from kit to areas of the new windshield that had tape on the stock windshield. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets and tighten all screws and acorn nuts to 23-27 in-lbs (2.6-3.0 Nm) . 5. Install windshield on motorcycle. Improper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b) Failure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a) NOTE Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. NOTE Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components. CARE AND CLEANING NOTE Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections

HARLEY DAVIDSON WINDSHIELD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove all hardware securing windshield. 2. Remove windshield. INSTALLATION 1. See Figure 1. Remove rubber trim strip from the original windshield and install on the replacement windshield. 2. Put the windshield into position. At each wellnut location use a scribe, or similar pointed tool, to make a pilot hole through the windshield tape where the mounting screw (4) goes into the wellnut (3). Install the mounting screws (4), with the nylon washers (5) and on 2004 models, the rubber washers (6) positioned as shown into the wellnuts (3). 3. Tighten mounting screws from the center to the outside edge on both sides. Tighten screws to 6-13 in-lbs (0.7- 1.5 Nm) . Well-nuts will expand to grip fairing CARE AND CLEANING NOTE Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan. Lexan is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. Failure to maintain Lexan properly can result in damage to the windshield. (00230a) Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a)

HARLEY DAVIDSON WINDSHIELD KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
and later FLTR Black wind deflector 57957-98 Fits 1998-2003 FLTR (Domestic) Standard height clear 57958-98A Fits 1998-2003 FLTR Plus 3″ taller, clear 58009-98A Fits 1998-2003 FLTR (International) Standard height, clear 58246-99A Fits 1998-2003 FLTR Low profile smoked 58453-98A Fits 1998 and later FLTR Smoked and contoured low profile 58753-01A Kit Contents Table 2. Kit Contents Part Number Description Quantity Not Sold Separately Windshield 1 There are no Service Parts available with this kit. REMOVAL 1. Remove all hardware securing windshield. 2. Remove windshield. INSTALLATION 1. See Figure 1. Remove rubber trim strip from the original windshield and install on the replacement windshield. 2. Put the windshield into position. At each wellnut location use a scribe, or similar pointed tool, to make a pilot hole through the windshield tape where the mounting screw (4) goes into the wellnut (3). Install the mounting screws (4), with the nylon washers (5) and on 2004 models, the rubber washers (6) positioned as shown into the wellnuts (3). 3. Tighten mounting screws from the center to the outside edge on both sides. Tighten screws to 6-13 in-lbs (0.7- 1.5 Nm) . Well-nuts will expand to grip fairing.

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

HARLEY DAVIDSON MULTI-POCKET WINDSHIELD BAG INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
Installation 1. Remove the acorn nuts from the inside-center, left and right on the horizontal windshield bracket. 2. Apply protective tape strips to the horizontal windshield bracket to protect chrome finish. 2. Place windshield bag and bracket with eyelets over screws in the horizontal windshield bracket. Mark the location of the vertical supports for correct placement of the rubber bumpers to protect the bottom of the bag bracket. Place two bumpers each at the marked locations of the vertical windshield supports. 3. Align the metal brace with the eyelets, to fit snugly onto the windshield horizontal bracket screws. 4. Fasten the acorn nuts removed in step 1 onto the screws through the eyelets under the windshield bag. Torque the nut to 90-110 in-lbs (10.2-12.4 Nm). NOTE The brace under the bottom of the windshield bag conforms to the contour of the windshield bracket as the acorn nuts are torqued. To keep this surface in the best condition, lightly wipe with a Harley-Davidson Micro Fiber cloth, part number 94663-02, using clear water or a mild Harley-Davidson cleaner such as: • Sunwash (part number 94659-98), • Bug Remover (part number 94657-98) or • Harley Gloss (part number 94627-98).

Kawasaki Mule 610 Windshield Installation And Operations Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Seizmik Hybrid Roof Frame Kit Contents: A. Windshield Mount Top Brackets and Hardware (2) B. Windshield Clamps and Hardware (2) (not shown) C. Windshield (1) (not shown) A B C D E F G H I J K L M Note: All hardware and brackets may not be shown in this view. Windshield Top Mount Hardware Includes: A. M6x22mm Socket Head Bolts (4) B. M6x12mm Socket Head Bolts (4) C. M8 Standard Flat Washers (4) D. Compression Sleve (2) E. M8x18mm Socket Head Bolt (2) F. Windshield Stay Assembly (2) G. 1.875″ Bar Clamp Half (4) H. Windshield bracket (2) I. Windshield clamp plate (2) J. Windshield clamp gasket (4) K. M6x25mm hex head bolt (4) L. M6 flat washer (8) M. M6 hex lock nut (4) Windsheild Lower Clamp Hardware (not shown) Includes: A. M6 x 40mm Zinc Coated Hex Head Bolt (2) B. M6 Standard Flat Washer (4) C. M6 Zinc Coated Nut (2) D. M6 Wide Flange Nut (2) E. 2″ Tube Clamp (2) F. 2″ Rubber Grip Strip (2) 3 Installation Instructions: Use the passenger side clamp to ensure proper positioning. The clamp should be positioned as shown. The driver’s side clamp should be even with the passenger’s side

Incoming search terms: