how to time ktm640 engune

You search Auto repair manual PDF how to time ktm640 engune, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to time ktm640 engune Direct Download speed 5282 Kb/s

  how to time ktm640 engune Full Version speed 6162 Kb/s



MPS Electronic Engine Kill Installation Instructions

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
blue wire should be connected to the normally open pole of the shift button. The Shift Button is a momentary type switch. The common pole of the shift button should be connected to a good ground and the normally open connects to the blue wire from the Electronic Engine Kill box. Electric Air Valve – The Electric Air Valve has two wires. These wires are interchangeable. One needs an ignition switched 12 volt power source. The other needs a ground signal when the shift button is depressed. The easiest way to do this is to locate the red and blue wires in the Electronic Engine Kill wire harness. Splice one Electric Air Valve wire into the red wire and splice the other Electric Air Valve wire into the blue. Once again soldering is the preferred method but you can use schotchlok splices. Setting Kill Time – Kill time is the amount of time the engine stays dead between gears during a shift. Generally the shorter the kill time the quicker the shift. The proper kill time will vary from bike to bike. Its generally better to start with to much kill time and work your way quicker. We generally start at around 75 ms. of kill time. The Kill Time is adjusted via a small potentiometer accessed through the grommet on the front of the unit. Using a small screwdriver Carefully turn the pot clockwise to the end of its travel. This is 100 ms of kill time. Now, carefully turn the pot screw counterclockwise to the end of its travel. This is 50 ms of kill time. Halfway in between is 75 ms. The pot only goes from 7 oclock to 5 oclock so don’t force it, they break easily! Testing The System – With no air in the system start the bike. Bring the rpm up to around 3000 rpm and push the shift button. You should hear a slight hesitation in the engine each time you depress the shift button. Once you establish that you have a engine kill when pushing the shift button remove the clevis pin from the shift cylinder and extend the shaft to the end of its travel. Air up the shifter to 120 psi. We also have onboard compressor kits available to conveniently fill the air tank on the fly or high pressure CO2 systems that can shift hundreds of times without refilling. With the engine off and the key on push the shift button

KTM 125 EXC, EXC SIXDAYS 200 XC, XC-W, EXC 250 XC, XC-W, EXC, EXCSIXDAYS 300 XC, XC-W, EXC-E, EXC-ESIXDAYS OWNER'S MANUAL 2008

0

Filed Under (KTM) by admin on 02-12-2010

download
Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket. Enter this number on page 1. Clutch lever The clutch lever [1] is located on the left side of the handlebars. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). OPERATION INSTRUMENTS » 1 2 A B
ENGLISH 6 OPERATION INSTRUMENTS » TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions. SPEED display mode / H (service hours) Only the SPEED / H and SPEED / ODO display modes are activated in the condition at delivery. SPEED/H is displayed whenever the display is activated and the front wheel is not turning. It automatically changes to the SPEED/ODO display mode as soon as the front wheel starts turning. SPEED displays the speed. H displays the engine’s service hours. The service hour counter starts to count as soon as you start the engine. The displayed figure cannot be changed. Service intervals are indicated in service hours for some KTM offroad motorcycles, making the service hour counter a very practical function. SPEED / ODO display mode (odometer) The SPEED/ODO mode displays the speed and the total distance traveled. The display automatically changes to the SPEED/H display mode when the front wheel stops turning. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. changes to the next display mode The electronic speedometer has a number of display modes (functions) that you can also activate (reveal) (see: Activating and deactivating display modes).
ENGLISH 7 OPERATION INSTRUMENTS » SPEED / LAP (lap time) display mode You can use the manual stop watch to stop and store up to 10 lap times, which you can view in the LAP/LAP display mode (see below). LAP displays the lap times in hours, minutes and seconds. + button Starts and stops the stop watch, lap time is not reset to 0 – button Stops the stop watch, stores the lap time and restarts the stop watch again. The time is reset to 0. A total of 10 lap times can be stored. If the lap time continues to run after you press the – button, all 10 memory locations are occupied.To clear all of the stored lap times, hold the button for 3 seconds in the SPEED/LAP mode.Up to 10 lap times can be stored in this way. briefly press buttonChanges to the next display mode.If no lap time is stored or the motorcycle is driving, the LAP/LAP mode will be skipped. hold button 3 secs. Clears all LAP figures SPEED / CLK (time) display mode CLK displays the time in hours, minutes and seconds. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. set the clock menu To set the clock, see „Setting the clock”. Activating and deactivating display modes In the display mode SPEED/H, press and hold the button for 3 seconds to access the SETUP menu. The active functions will be displayed. The blinking function can be activated by pressing the + button and deactivated by pressing the – button. Press and hold the button 3 seconds to store the settings. If no button is pressed for 20 seconds, the setting will be stored automatically and the display will return to the SPEED/H mode. + button activates the blinking display – button deactivates the blinking display briefly press buttonchanges to the next display without changing any settings hold button 3 secs. starts the SETUP stores the settings and changes to the SPEED/H mode

Incoming search terms:

SUZUKI GSX 1300R OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 01-12-2010

download
CLOCK/FUEL INJECTION SYSTEM INDICATOR (D The indicator displays clock under normal condition. The indicator switches from the clock to the fuel injection system indicator if the fuel injection system has any failure. Clock mode The clock indicates 12-hour mode. Follow the procedure below to adjust the clock. 1. Push the button® until the display blinks. 2. Pushing the button will advance one minute at a time. Repeat pushing the button until the display reaches desired time. 3. Keeping the button pushed in will advance ten minutes at a time. Keep the button pushed until the display reaches desired time. Fine- tune the time by pushing the button repeatedly. 4. Wait 5 seconds and push the button to resume to time display. Fuel injection system indicator F I The fuel injection system indicator indicates “Fl” or “CHEC” if the fuel injection system has any trouble. The Fl indicator light (D will also come on if the fuel injection system has failure. No 1 2 3 Fuel injection system indicator Fl Fl/Clock alternately CHEC Fl indicator light Blinks Lights – Engine condition Engine does not start. Engine can start. Engine does not start. 14 If the fuel injection system indicator displays “Fl” and Fl indicator light blinks, the engine will not start due to a serious fuel injection system failure. If the system has serious failure while riding, the engine may stop. When the fuel injection system indicator displays “Fl” and clock alternately and Fl indicator light comes on, the engine can be started and a will keep running with limited engine performance. This shows that the fuel injection system has minor failure. Bring your motorcycle to an anthorized Suzuki dealer or qualified mechanic to inspect the motorcycle. Continuous operation in this condition may seriously damage the motorcycle. 3. When the fuel injection system indicator indicates “CHEC,” the engine will not start. Make sure that the engine stop switch is turned on and the transmission is in neutral position with the side stand fully up. If the indicator still indicates “CHEC,” inspect the ignition fuse next. SPEEDOMETER ® The speedometer indicates the road speed in kilometers per hour and miles per hour. RIGHT TURN SIGNAL INDICATOR LIGHT © When the right turn signals are operated, the indicator light will flash at the same time. NOTE: If the turn signal light is not operating properly due to bulb filament or circuit failure, the indicator light flickers more quickly to notify the rider of the existence of trouble

TOYOTA E ECU / COLD START INJECTOR TIME SWITCH MODIFICATION

0

Filed Under (Toyota Manuals) by admin on 17-10-2011

download
Before replacing an ECU or a cold start injector time switch, perform a thorough inspection to verify that all engine mechanical, fuel and electrical/electronic systems are to recommended specifications. PARTS RETURN INFORMATION: The replacement ECU’s are remanufactured by Nippondenso-Los Angeles (NDLA). In order to maintain cores for rebuilt units, the original ECU must be sent to NDLA as soon as it has been replaced.

Harley davidson Sportster Custom Straightshot Exhaust System REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake master cylinder. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips . INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the circlips and flanges from the stock system on to both of the new head pipes. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe using the stock nuts, do not tighten at this time. 5. Install the rear head pipe using the stock nuts, do not tighten at this time. 6. Install one muffler clamp (supplied) over the inlet (notched end) of each muffler. 7. Identify the front and rear muffler mounting brackets. The front bracket is stamped with the number 305 and the rear muffler bracket is stamped 213 . 8. Install the front muffler mounting bracket to the stud on the engine (where the stock muffler mounted) and fasten using the stock nut (leave loose at this time). The bracket will bend inward towards the center of the motorcycle when installed correctly. Note: You may need to move the wires and hoses on the lower frame rail to decrease the possibility of them chaffing on the bracket bolts. 9. Slip one of the mufflers onto the front head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using the 5/16″ flange head bolts (supplied) leave them loose at this time. 10. Attach the rear mounting bracket to the rear muffler. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the bracket to the muffler using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note: The single hole in the bracket will point downward and slightly forward when installed correctly

BMW R/ K Series LEFT AND RIGHT TURN-SIGNAL SWITCHES INSTALLATION MANUAL

0

Filed Under (BMW) by admin on 17-11-2010

download
On most models, access to the turn signal flasher is possible simply by removing the seat and locating it within the wiring harness underneath. On some models, it is located inside the front fairing. If in doubt, turn it on and follow the clicking sound to locate it. Refer to your bike’s Manual, or the Wiring Diagram to find its location. TIME-OUT SELECTION To set the length of time, after which the signalMinder will stop flashing: n Make sure the power is turned OFF. o Set the time-out by appropriate selection of the DIP switch # 2 # 3 TIME FLASHES OFF OFF 8 sec 10 ON OFF 16 sec 20 OFF ON 24 sec 30 If you elect to install other optional features, please refer to: Ñ Optional Hook-ups section Ñ Special Features and Functions Ñ VL-10 vectraLIGHT plug-in ports Enhance your visibility! – use all available features. NOTE! The 4-Way flash or Test Mode flash features are not enabled unless the Running Light Option is hooked-up. Typical location of signal flasher Page-4 SM-2 SM-2 Application: Ñ Older Japanese models Ñ BMW F650 and early air- cooled models signalMinder ™ FEATURES: Ñ Plug-n-Play replacement for: – existing turn signal flasher Ñ DIP Switch selection for: – 8, 16 or 24 seconds time-outs – Running Light intensity Ñ Built-in 3-Pin connector for: – Running Light Conversion option – Brake Input option Ñ Molex 3-pin wire harness for: – easy hook-up using Scotch-locks Ñ 4-Way Emergency flash mode, or – Test Mode flash Ñ Built-in driver ports for vectraLIGHT – mirror mounted LED array with SEQUENTIAL flash, Running lights and Brake override

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

Incoming search terms:

1981 Vespa P 200E Engine Specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Engine Specification – Malossi 210 Bodywork or other specialised parts – Malossi kit and pm pipe Cruising Speed and Top Speed — 60 and 80 on a good day Paintwork – Red with ‘Rasher’ from the Beano on Accessories – Rusty grab rail and battle scars Known History of the Vehicle – was one of Stoker’s scoots from a long time ago (1989 ish). Originally came from Milton Keynes. Sold on to Jason ‘Reg’,Redgers, who used it for a while, but then emigrated to Sweden – but left the scooter at his parents’ houses (they moved a few times, and each time had to house the beast for him!). It has not been on the road since about 1992, but now it has been brought back from the dead to be once again thrashed by a slightly younger rebel!! Time taken to build and by who?- Mr. Dan Stokes can have the credit for that Hardest Part of the Project – ? Ask him, but I don’t think he would remember. (Didn’t hardly use it, cos I had an a RD350LC at the same time so that used to get thrashed instead!! DS) Overall Cost (time and money) approx. – Who cares? Overall Cost that you have told your wife – Cheaper than most of scooters owned

Incoming search terms:

YAMAHA ROAD STAR LONGSHOT EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 28-12-2010

download
1. Remove the header flange nuts from the rear cylinder. 2. Loosen the muffler clamp on the front head pipe. 3. Remove the two muffler mounting bracket bolts, located between the two mufflers. 4. Carefully separate the front head pipe from the muffler assembly. Remove the muffler assembly with the rear head pipe attached and set it aside. 5. Remove the header flange nuts from the front cylinder. Remove the front head pipe and set it aside. 6. Remove the muffler mounting bracket from the frame. Note: The rear brake hose must be disconnected from the rear brake caliper in order to remove the muffler mounting bracket. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Reconnect the brake hose to the rear caliper. Important : Bleed the rear brake to remove any air from the system and refill the reservoir with the proper brake fluid. 2. Install the new mounting bracket (stamped 274) to the frame, by aligning the two 10mm holes in the bracket with the two holes in the frame below the right rear footrest (where the stock mounting bar was removed). Use the two 10mm bolts and lock nuts (supplied), do not tighten at this time. Note: The bracket will bend away from the motorcycle when mounted correctly. Refer to figure 1. 3. Connect the brake hose clip to the muffler mounting bracket, using the 6mm bolt and lock nut (supplied). Refer to figure 1. 4. Install the chrome flanges (supplied) on to both the new head pipes. 5. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 6. Install the front head pipe using the stock nuts, do not tighten at this time. 7. Install the rear head pipe using the stock nuts, do not tighten at this time. 8. Install one muffler clamp (supplied) over the front (notched end) of each muffler. 9. Slip one muffler onto the front head pipe. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of the muffler and attach the muffler to the mounting bracket using two of the 5/16″ flange head bolts (supplied), but leave them loose at this time. 10. Repeat step #8 for the rear muffler. 11. Align the mufflers so they are parallel when viewing from the right side of the bike, and tighten the 5/16″ flange bolts on the back side of both mufflers. 12. Tighten the two 10mm bolts that mount the bracket to the frame. 13. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 14. Place the appropriate heat shield onto the rear pipe, wrap the hose clamps around the head pipe and tighten. Repeat this step with the front heat shield

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

Incoming search terms: