how to wire accessory lights 2006 stratoliner

You search Auto repair manual PDF how to wire accessory lights 2006 stratoliner, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to wire accessory lights 2006 stratoliner Direct Download speed 5282 Kb/s

  how to wire accessory lights 2006 stratoliner Full Version speed 6162 Kb/s



LED SHOW LIGHTING INSTALLATION INSTRUCTIOINS

0

Filed Under (Tips and Review) by admin on 27-12-2010

download
1. The kit is supplied with 4 “cluster” lights that project a round flood lighting pattern and 4 “array” lights that have a narrow fan type pattern. Determine where you would like to mount the supplied lights, switch and wiring connections. You may want to hook up one of the lights with some long jumper wires connected to the battery and hold it in various places to see what will show off your bike best. The idea is to see the light reflected off your bike and not see the light fixture. 2. Mount the lights and switch using the supplied primer and 2-sided adhesive pad. Apply the primer to the backside of the lights and switch; let it dry for 5 minutes. Remove the protector from one side of the adhesive pad and apply. Apply the primer on the motorcycle where the lights and switch will be mounted and let it dry for 5 minutes. Remove the protector from the adhesive pad and mount the lights and switch. 3. Refer to the provided wiring diagram. The wiring is color-coded and connects in parallel. All of the black wires connect together through the BLACK wire of the 2 conductor black jacketed wire (Ground Wires). All of the colored wires connect together through the RED wire of the 2 conductor black jacketed wire (Power Wires). Connections may be soldered, crimped with solderless connectors, or twisted together. 4. Measure and cut the supplied 2-conductor black-jacketed wire to the lengths that are needed to connect the lights and switch. When routing the wire from any lights that you have mounted to the front make sure you have provided enough slack at the steering head to be able to turn the front wheel full left and full right without damaging the lights or wires. Also be sure the wire is at least æ” from any exhaust pipe. 5. Join each connection and cover with the supplied heat shrink tubing. NOTE; All wire connections must be insulated. Cut a piece of the provided heat shrink tubing long enough to cover the connection completely. 6. Connect one wire from the switch to the RED wire of the lights with one of the supplied blue butt connectors. Connect the second wire from the switch to one wire from the fuse holder with the other blue butt connector. Connect the second wire from the fuse holder to the positive (+) battery terminal using one of the supplied fork connectors. 7. Connect the BLACK wire of the lights using the other fork connector to a ground connection. (The negative (-) battery terminal or motorcycle frame.) 8. Secure all loose wires by using the supplied cable ties. Check the front wheel again to be sure there is enough wire slack for turning.

BMW R1200GS Dual Function LED Running Lights and Flashing Brake Lights installation instructions

0

Filed Under (BMW) by admin on 08-11-2010

download
The flasher is set to flash continuously as long as the brake is applied. To convert to a 5 second flash and then stay solid while the brake is applied, cut the green wire loop on the flasher. Use electrical tape to protect and secure the green wires to the other wires. 2. Remove the rider’s seat. Locate the wire bundle that starts at the rear of the motorcycle. At the most accessible spot carefully remove 3″ to 3½” of protective wire loom. I know, I know…it’s really beautifully done. Cowboy up! Take it off! 3. Mount the flasher in a location that will not crimp wires or interfere with the other bike assemblies. Locate the +12 volt wire ( GRAY wire with BLACK stripe and YELLOW banding) from the brake light Attach the kit RED wire to the brake light positive wire using one of the Posi-Tap connectors in the kit. 4. Locate the Ground wire ( BROWN wire) from the brake light. Attach the kit BLACK wire to the motorcycle ground wire using a Posi-Tap connector. 5. If you have a Fuse Block with ignition switched relay installed, route the Hyper-Lite GRAY wire to a fused circuit on the (relay activated) fuse block . 6. If you do not have a Fuse Block installed, find the alarm circuit connector under the seat . The alarm circuit has a rectangular connector and five wires, White with Black stripe; White with Brown stripe; Red with White; Brown with White; and Green with White stripe. Use a Posi-Tap to attach the Hyper-Lite GRAY wire to the green wire with white stripe. Pull the wire loom back from the wire. Tap into the wire with the Posi-Tap provided. . 7. If using the Hyper-Lite License Plate Mounting bracket, install it now. OR: Clean the side facing reflectors at the rear of the bike with alcohol. Mount the LED modules vertically on the reflectors so that the LEDs point straight back. Press in place for about 5 seconds. The tape can be used only once! If you goof, new tape is required. 8. Route the BLUE and BROWN wires from the flasher and the LED modules. Trim the Blue and Brown wires to remove any excess wire . Use a Posi-Twist to connect the 3 BLUE wires together. Use a Posi-Twist to connect the 3 BROWN wires together. (see Posi-Twist Connector instructions)

Incoming search terms:

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

YAMAHA ROADLINER AND STRATOLINER LAY DOWN LICENSEPLATE/ TAIL LIGHT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate holder assembly from the rear fender (three 8mm Allen bolts 5mm wrench). Remove the five 4mm Allen screws underneath the rear fender which secure the taillight/turn signal assembly to the rear fender (3mm wrench). As shown in photo #2, pull the taillight assembly out away from the fender, turn it over, place a towel or rag between the light and fender and allow it to rest on the fender. 2. Locate the supplied triangular license plate mounting block, two 8 x 20mm Allen screws with holes driiled thru and three rubber washers. Place the two Allen screws thru the upper holes in the block and the rubber washers over the screws on the backside of the block. Start the screws into the upper holes on the fender. Use one of the three screws removed earlier from the original mount in the remaining lower hole of the new block sliding the remaining rubber washer between the block and fender. Tighten all three Allen screws secure enough to compress the rubber washers (4-6 ft lbs.). 3. Locate the supplied license plate mounting plate and LED lights. Cut off the excess red and black wires at the end of the black loom or tube. Referring to photo (1) thread the wires of the LED lights thru the small holes in the mounting plate, peel the cover from the adhesive backing on the lights and press them firmly into place as shown. 4. Locate the three supplied ¼” x ½” flat head Allen screws. Hold the plate up to the mounting block installed earlier with the wires at the bottom of the plate. Thread the wires from the LED lights thru the holes in the upper bolts of the block. Install the plate onto the block using the three flat head screws being sure to keep the exposed wire behind he plate as short as possible and fitting into the slot or cut out at the edge of the block. Snug the screws and again check to see tat the wires are in the slot or cut out in the block and do not become pinched as the screws are tightened. Tighten the screws securely. 5. Where the wires from the taillight go thru the fender there is a grommet, pull this grommet out from the fender. Thread the wires from the LED lights thru the grommet with the other wires. Replace the grommet into the fender and remove any slack from the wires under the fender. Cut the LED wires off at 6″ past the grommet. 6. Referring to photo (2) remove 2″ of the black tubing exposing the red and black wires on the LEDs. Locate the supplied brake/tail light dual function element (a red wire at one end with a red and orange wire at the other) and wire connectors. Cut all three wires on the dual element to 3″ long. Strip the end of the single red wire on the element and both of the red wires from the LEDs then connect them using one of the blue butt connectors. Connect the two black wires from the LEDs to any one of the black wires on the tail light or signals using one of the supplied splice connectors (place both black wires into one of the holes on the connector). Using the remaining splice connectors attach the red wire from the dual element to the yellow wire on the tail light and the orange wire to the blue wire on the tail light. Turn on the ignition and check that the LEDs are working both as tail and brake lights when the brakes are applied.

Incoming search terms:

HONDA Ground Effects Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
Wiring Installation: 1. Remove the four M8x1.25 socket head cap screws from the seat and remove the passenger handles and seat. 2. Remove both rear side covers, and right front side cover. 3. Remove the two M3 Phillips head screws and two trim clips from the right front storage pocket. 4. Place the three relays of the Ground Effects Ground Effects Ground Effects Ground Effects wiring harness underneath the relay box. 2001 2001 2001 2001 — – 2005 MODELS 2005 MODELS 2005 MODELS 2005 MODELS Route the long end of harness (blue wire and orange wire), behind the fuel tank to the brake lines. The shorter section of the harness will end at the brake lines. Continue along the brake lines to the main harness of the motorcycle to the shelter, then up through the shelter to the pocket area. 5. Locate the harness connectors under the pocket. Go to step 6. 2006 & NEWER MODELS 2006 & NEWER MODELS 2006 & NEWER MODELS 2006 & NEWER MODELS Route the long end of harness (blue wire and orange wire), under the relay box and connect to the Positions Relay. 6. Connect the orange wire to the orange wire with white tracer using a scotch-lok connector. Connect the blue wire to the light blue wire with white tracer using a scotch-lok connector. 7. Route the red and white wires behind the fuel tank, along the left side wiring harness to the fuse box. 8. Connect the RED wire with eyelet connector attached, to the positive side of the accessory terminal in the fuse box. 9. Connect the WHITE wire to the negative battery terminal. 10. Connect the brown wire with white tracer to the brown wire with white tracer (tail relay in relay box) using a scotch-lok connector. 11. Route the orange wire with black tracer and the white wire behind the fuel tank, with at least 6 inches of wire left hanging below the bike. 12. Reinstall the right fairing pocket with the two M3 Phillips head screws and two trim clips. 13. Replace the right front side cover and the right and left rear side covers. 14. Replace the seat and passenger grip handles with the four M8 x 1.25 socket head cap screws

HARLEY DAVIDSON DETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE If your motorcycle has directional lights mounted on the upper fork bracket they must be relocated to the bottom fork bracket. Some models have front directional lights equipped with three wires, the third black wire is a ground wire. Check to determine how many wires are connected to the front directional lights and follow the following procedure that applies. Ifdirectional lights are not mounted on the upper fork bracket proceed to “ASSEMBLING FAIRING”. Relocating Two Wire Directional Lights 1. Support motorcycle on a center stand such that front wheel is raised slightly off the ground. 2. Remove fork tube pinch screw from right side of lower bracket. 3. Cut wires connected to right directional light about 2 in. away from directional light body. 4. Remove fork tube pinch screw from right side of upper fork bracket. (This is the screw that secures the right directional light.) 5. Install right directional light on right side of lower fork bracket using pinch screw removed in step 4. Install pinch screw removed in step 2 into right side of upper bracket. Tighten both pinch screws to 30-35 ft-lbs. 6. Repeat steps 1 through 5 to relocate left directional light. NOTE Fork tubes may slide downward within fork brackets. If this occurs, front fork tube extension above front fork upper bracket will have to be readjusted according to appropriate Service Manual procedures. 7. Connect the right directional light as follows: Strip approx. 5/16 in. of insulation from the wires cut in step 3. 8. Crimp solderless connectors from kit on two wires coming from motorcycle. 9. Split one end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 10. Slide a piece of shrink tubing from kit over each of the wire ends stripped in step 9 and crimp the wires into the terminals installed in step 8. Make sure you connect the silver and copper colored wires to like colored wires. NOTE Polarized wire is used in this application to ensure correct wiring. One wire is silver, one is copper colored. Wire colors of spliced wire must match wire color of original directional wire leads. 11. Cut polarized wires to the length required for connection to the wires at the relocated directional light. Make certain you leave enough slack in wires to allow routing the harness along the fork tube. 12. Split remaining end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 13. Slide heat shrink tubes over the two wire end. 14. Strip 5/16 in. of insulation from wires connected to directional light and connect like colored wires at directional light with connectors from kit. 15. Slide heat shrink tubing over connectors installed in steps 10 and 14. Activate shrink tubing with heat gun or hair dryer.

SR-C400 Motorcycle Security System INSTALLATION MANUAL AND USER'S GUIDE

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Routing the Antenna Wire The MCM includes an 18″ antenna wire. The first 12″ is a coaxial wire; the remaining 6″ is the reception antenna wire. When routing, try to avoid running the antenna along or near metal. For best performance, have the antenna wire as vertical as possible and exposed. Wire Connections The system includes one harness (HAR-1a) that connects directly into the MCM. The harness is split into three plugs: one for the GEN-1a connector, one for the optional SN-5 connector and one for the data output for future expansion. Note: Each plug is unique and will only fit the appropriate component one way. Main Harness Note: If the optional factory connector kit is being used, please disregard this section of the instructions and refer to the instructions supplied with the factory connector kit. The main harness consists of two harnesses. One is labeled (HAR-1a) and the second is labeled (GEN-1a). Plug in the white 4 pin connector from the (HAR-1a) into the matching 4 pin connector from the (GEN-1a). The (HAR-1a) also has a waterproof connector that plugs into the MCM. The wires should be connected as follows: HAR-1a Black wire with fuse and ring terminal – To battery Positive (+). GEN-1a Black wire – To ground (-). Orange wire – To tail light wire or any other wire that is hot (+) when ignition is ON (NOTE: this is an input to the alarm this connection is not designed to flash the tail light). Color Codes: Ground (-) Tail Light Honda Green wire Brown wire Kawasaki Black wire Red wire Suzuki Black/White Brown wire Yamaha Black wire Blue wire Harley Davidson Black wire Blue wire

Incoming search terms:

Motorcycle LED lights RENEGADE LIGHTS Disconnection Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Disconnect the fuse holder from the battery – both the positive ( +) and negative ( -) sides. 4. Cut the wire to the light that is not working with the side cutters. 5. At the problem light twist the light case back and forth slowly and then pull firmly, DO NOT yank to remove from the motorcycle. 6. If the motorcycle led light does not come off easily, repeat the twisting motion back and froth until you feel the light loosen – then pull. 7. Pull the motorcycle led light away from the motorcycle slowly until the cut end of wire falls free. 8. If you will NOT be using your motorcycle until the new lights arrive, you may stop at this step. SAFETY POINT: Otherwise, where you cut the wire, you need to dead end or tape the cut wire. This will keep it from shorting out until the new motorcycle led light is installed. 9. Reconnect fuse holder to battery. 10. Reconnect the battery and then install the seat. 11. Return the motorcycle led light or lights to Renegade Lights along with Warranty Return Policy Form. 12. Renegade Lights will return your new motorcycle led lights along with instructions for installing them.

Incoming search terms:

1982-2005 Harley Motorcycle Removal and Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
” bolt from the mounting stem on the Signal® mirror. While seated on the motorcycle, position the Signal® mirror on the handle bar. Secure the Signal® mirror to the handle bar using the 5/ 16 ” bolt. Make sure the bolt is tight! Guide the Signal® mirror wire harness into the cowling by going along side the existing factory wire harness. 4 Remove any slack in the wire harness. Secure the wire harness to the handle bar using a supplied tie wrap. 5 6 Adjust the position of the Signal® mirror and tighten the ball retention screws. Remove the motorcycle seat. Remove the aft mounting bolts on the fuel tank. 7 Guide the Signal® mirror wire harness along the inside of the fuel tank’s front mounting bolt and between the crossover tube. 8 9 Lift up the aft portion of the fuel tank and guide the Signal® mirror wire harness down the backbone of the motorcycle frame, alongside the existing factory wire harness. The motorcycle’s electrical wiring for turn indicators is located aft of the gas tank on the backbone of the frame. Guide the new wire harness from the Signal® mirror to the electrical wiring. Cut off any excess slack in the wire. Locate the SOLID BROWN wire from the wire connector. Turn the ignition key so that electrical power is on and activate the right side turn indicator. Probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘right side turn’. Repeat all of the previous steps to replace the left side factory mirror with the new Signal® mirror. Locate the SOLID VIOLET wire from the wire connector. Activate the left side turn indicator and probe the wire with the wire tester to verify that flashing turn indicator power is present. Label that wire as ‘left side turn

TOYOTA COROLLA 1984-2006 VEHICLE WIRING VEHICLE WIRING REMOVAL

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
IRING INFORMATION: 1984 Toyota Corolla FWD WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE OR WHITE/RED Ignition Harness STARTER WIRE BLACK/WHITE Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/ORANGE Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) BLUE/WHITE Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) BLUE/RED Harness In Driver’s Kick Panel PARKING LIGHTS (+) DK. GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) LT. GREEN Harness At Steering Column HEADLIGHTS (-) RED/WHITE Harness At Steering Column DOOR TRIGGER (-) RED/WHT OR BLK/WHT Harness At Fuse Box TRUNK TRIGGER COMMON WITH DOORS (Hatchback Only) TACHOMETER WIRE BLACK At Ignition Coil BRAKE WIRE (+) GREEN/WHITE Brake Pedal Switch HORN TRIGGER (-) GREEN/RED Steering Column LEFT FRONT WINDOW UP GREEN/BLACK At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/RED At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP GREEN Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/WHITE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN RED/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN BLUE/BLACK Harness In Driver’s Kick From Driver Doo

Incoming search terms: