how to replacing fork seals on gl1800 goldwing

You search Auto repair manual PDF how to replacing fork seals on gl1800 goldwing, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replacing fork seals on gl1800 goldwing Direct Download speed 5282 Kb/s

  how to replacing fork seals on gl1800 goldwing Full Version speed 6162 Kb/s



HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

Incoming search terms:

HARLEY DAVIDSON FX SOFTAIL FRONT LOWERING SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (T), lockwashers (S), flat washers (R) and axle cap from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) and spacer (O) from fork tube plug (B). Remove quad ring seal (D). Save bolt and spacer but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring -J03923 1 of 4 pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring (1). 11. Remove dust cover (E). 12. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 13. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 14. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). NOTE The lower stop (L) may come out with the damper tube or remain in the slider tube. Ensure that the lower stop is removed from the slider tube. 15. Remove the lower stop (L). 16. Remove damper tube (2) from fork tube. 17. Remove rebound spring (F) from damper tube. 18. Repeat Steps 1-17 for the opposite side fork assembly. Fork Assembly

HARLEY DAVIDSON FL SOFTAIL PROFILE LOW FRONT SUSPENSION KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
Fork Spring Removal 1. Elevate and support the vehicle so the front tire is off the floor and the forks are fully extended. 4 9 3 1 10 11 2 5 6 7 8 is04004 1. Slider tube cap 2. Spacer washer 3. Oil seal 4. Clamp bolt and washer 5. Fork tube plug 6. O-ring 7. Fork spring 8. Tight-wound end of spring 9. Fork slider tube 10. Fork slider 11. Drain screw and washer Figure 1. Front Fork NOTE Remove the brake caliper from the fork slider. DO NOT remove the brake line from the caliper. 2. Remove the front wheel. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. 3. Remove the front fender. See FRONT FENDER in the Service Manual. 4. See Figure 1. Remove the slider tube cap (1), spacer (2) and oil seal (3) from the top of one fork side. Save the cap and spacer. The oil seal can be discarded. 5. Loosen the clamp bolt (4) and pull the fork from the brackets. 6. Repeat Steps 4 and 5 for the other fork side. -J00280 1 of 4 Wear saf ety glasses or gog gles when ser vicing f ork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) NOTE Be careful not to damage the O-ring. 7. See Figure 1. Remove the fork tube plug (5) and O-ring (6). Pull the spring (7) out of the slider tube (9). Remove the drain screw and washer (11), and drain the fork. Reinstall the drain screw and washer, and tighten to 52-78 in-lbs (5.9-8.9 Nm). 8. Repeat Step 7 for the other fork side. NOTE The Profile® Low Front Suspension Kit requires a different amount of H-D TYPE E FORK OIL than is listed in the Service Manual. NOTE Measure the oil level from the top of the fork tube with the fork spring removed and the fork fully compressed. 9. See FRONT FORK OIL in the Service Manual, but substitute the measures below. Fill the forks with Harley- Davidson TYPE E FORK OIL: • 1986 through 1999 models: •11.7 oz (345 cc) of oil, or •5.2 inch (132 mm) from top of oil level to top of tube. • 2000 and later models: •13.4 oz (396 cc) of oil, or •4.1 inch (104 mm) from top of oil level to top of tube. Fork Spring Installation 1. Insert a new Profile Low spring (7) from the kit into each slider tube (9), with the tight-wound portion (8) toward the bottom of the fork slider. NOTE Be careful not to damage the O-ring. 2. Install the fork tube plug (5) and O-ring (6) assembly into the slider tube and tighten securely. Be sure that one flat on each fork tube plug faces toward the inside of the fork. 3. Insert both fork side assemblies up through the slider covers, the fork stem and bracket, and the upper bracket. 4. Obtain two new oil seals (3), H-D Part Number 45733-48, and the spacer washers (2) and slider tube caps (1) saved earlier. Place an oil seal, followed by a spacer washer, onto each fork tube plug. 5. Insert the threads of a slider tube cap through each washer and seal, and into the fork tube plugs. Tighten to 40-60 ft- lbs (54.2-81.3 Nm). 6. Tighten the fork stem bracket clamp bolts (4) to 30-35 ft- lbs (40.7-47.5 Nm). 7. Install the front fender. See FRONT FENDER in the Service Manual. Install the front wheel and brake caliper. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. Jiffy Stand Removal/Installation 1. Move the jiffy stand to the retracted (up) position. Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c) 2. See Figure 3. Unfasten the jiffy stand leg spring (A) from the vehicle. Remove the hex bolt (B), lock washer (C), flat washer (D) and leg stop (E) from the threaded end of the jiffy stand leg. Discard the jiffy stand leg, but retain all other components. 3. Clean and inspect the jiffy stand attaching parts and mounting bracket for wear or damage. If parts replacement is necessary, refer to the Jiffy Stand section of your Service Manual for replacement procedures

Incoming search terms:

Harley Davidson 39 mm Front Spring Lowering Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Support the motorcycle so the front wheel is off the ground. Next remove the front wheel and fender. Remove the fork cap nuts and loosen the lower triple clamp pinch bolts. Remove the front brake caliper. Some models have a tapered end to the fork tube. Extra effort will be required to remove the tube from the crown. Loosen the top fork cap 1 to 2 revolutions. Use a soft wood block or similar tool (that will not mark fork cap finish) and tap down with mallet to loosen fork tube from its tapered fit in top steering crown. Make sure fork pinch bolts are loose. To completely remove fork of this style, unscrew the fork cap entirely. 2. Slide both fork assemblies out of the triple clamps. Unscrew the top fork tube plugs. Remove the plugs and fork springs. CAUTION: Fork caps are under spring pressure and could cause serious injury. Drain the fork oil by turning the fork assemblys upside-down. 3. Next, bottom the fork tube into the fork leg. DO NOT extend the tube while you remove the allen bolt on the bottom of the fork leg. Turn the assembly upside-down and shake the damper rod and rebound spring out of the fork assembly. Again, DO NOT extend the tube during this. Extending the tube could dislodge the internal bottoming cone, which fits on the end of the damping rod, making it very difficult to reinstall the damper rod without complete fork disassembly. 4. FOR 1″ REDUCTION IN FORK LENGTH: You must first measure the length of the O.E.M. rebound spring. Depending on the model of the motorcycle, the length will either be 1″ or 2″ long. A. If you currently have a 1″ rebound spring, you need to replace it with the 2″ long LA Choppers rebound spring (included in the kit), then reinstall the damper rod in the fork tube. B. If you currently have a 2″ rebound spring, you will need to add the 1″ long spacer, then reinstall the damper rod in the fork tube.

HONDA GL1200 fork seals Removal And Installation Manual

0

Filed Under (Honda) by admin on 27-02-2011

download
subsequent seal failure it can cause, is to cover or “shield” the tubes in some manner that goes beyond the normal protection offered by dust seals. My old CB200T has the traditional, accordion-rubber “gaiters” over the shock tubes, and the seals have failed only once in 12 years, at 80,000 miles. That’s why you still see gaiters on virtually every off-road bike made. But somewhere along the line “fashion” and “design” overcame common sense, and we all started insisting on street bikes with modern-looking, totally exposed, polished fork tubes. Gaiters were dropped almost entirely, determined to be much too old-fashioned-looking, or as contributing in some miniscule manner to fork “stiction.” Maybe so—but they worked. Some riders, wise to the ways of seal failure, have developed “home remedies” to protect their forks. Among the ones I’ve seen are sections of rubber hose attached to fork housings with hose clamps, or the more attractive addition of vinyl “wrap-arounds” that velcro around the tubes and slide up and down with the forks. Some of these are even color-matched to the bikes. I used to own a Honda GL1200 that needed the fork seals replaced at 21,000 miles, 43,000 miles, and 62,000 miles. Then I covered the exposed upper tubes with vinyl “sliders,” and never had to replace the seals again. The bike’s current owner now has the odometer up to 124,000 miles, and the seals are still holding. Honda must have gotten wise to this, because the GL1500 models came with plastic “fork shields” built right onto the front fender. Even though they don’t quite cover the entire exposed area of the tubes

Incoming search terms:

HARLEY DAVIDSON FXST BLACK FORK SLIDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION The fork sliders included in this kit install in the same way as the original equipment parts. NOTE Prior to installation of this kit, check the bores of the new sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s), and front wheel according to instructions found in the Chassis section of the appropriate Service Manual. NOTE On some models other parts will also need to be removed to access the front forks. See the Service Manual. 3. Drain and remove the front forks. See the Chassis Section of the Service Manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 4. Disassemble the front fork tubes according to instructions in the Service Manual, and replace the original fork sliders with the black sliders from the kit. 5. Assemble the front fork tubes, replacing worn seals, bushings or other additional items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 6. Tighten the drain screws to 52-78 in-lbs (5.9-8.8 Nm) 7. Fill with Harley-Davidson TYPE E FORK OIL according to the instructions found in the Service Manual. 8. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel, and caliper(s) according to the instructions found in the Chassis section of the Service Manual. Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b) 1 is02733 1. Install bottom of reflector 2.0 inches above center of axle Figure 1. Reflector Placement NOTE The front reflectors located on both sides of the fork sliders will be removed, cleaned and installed on the new chrome fork sliders. 9. See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side to side until it can be removed. Retain reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. 10. Peel off any excess adhesive from both reflectors. Surface must be clean for reinstallation. 11. Peel off one side of backing on foam double sided tape. Press firmly on tape to secure it to reflector. Repeat double sided adhesive tape installation on remaining reflector. NOTE The bottom edge of reflector should be two inches (50 mm) above the center of the axle shaft. 12. See Figure 1. Remove second side (outside surface) of adhesive backing. Place reflector in position (1) and press reflector firmly into place to activate the adhesive. Repeat for remaining reflector. 13. Pump brakes prior to test riding vehicle.

Incoming search terms:

Street Fork Spring Installation Instructions

0

Filed Under (Tips and Review) by admin on 13-02-2011

download
1. Remove fork springs according to instructions contained in your shop manual. For maximum performance we highly recommend that the forks be thoroughly cleaned, inspected and new fork oil installed. Note: If your motorcycle comes equipped with two fork springs in each leg (long & short), remove and discard both springs and the flat washer between the springs. If a stock spacer exits, remove it. If there is a short spring on the damper rod, do not remove it! 2. Use the recommended fork oil viscosity as noted in your owners manual with the following exceptions: GL1100 20 weight, GL1200/1500 15 weight required. See fine tuning for more in- formation. Fork oil level/volume should be checked according to the steps outlined in your authorized shop manual. Measurement of your fork oil by level is the preferred method. However, some manuals only specify a volume measurement. Due to the design of a progressive wound fork spring it will displace more oil thus requiring a maximum oil level of 5.5″ (140mm). Caution: This is not a recommendation, it is only a precautionary statement. If your manual specifies an oil level higher than 5.5″ (140mm) set the oil level at 5.5″ (140mm). (Oil level is the distance from the top of the fork tube to the top of the oil with the fork completely collapsed and the fork spring removed see figure 1.) This measurement can be made by using either one of the Progressive Suspension Fork Oil Level Adjusters (FOL-1 or FOL-2). 3. Install your new fork springs into the forks. Mechanically, it makes no difference which way the springs are installed. Some manuals will state; install the spring with the close wound end towards the bottom. This is done because sometimes there will be less spring noise. The springs will perform exactly the same regardless of which direction they are placed. Check the spacer length requirement for your motorcycle in the enclosed supplement. If not listed, you must calculate the pre-load. What is pre-load? Pre-load is the distance the spring compresses when the fork cap is installed. You may or may not utilize a spacer to achieve proper pre-load. The spacer in itself is not “pre-load”. It just helps to achieve it. Why is pre-load important? It determines the proper ride height which in turn affects how the bike handles.

Suzuki B-King GSX1300 BK Suspension Removal and Installation

0

Filed Under (Suzuki) by admin on 01-12-2010

download
Front Fork Removal and Installation B823H12206002 NOTE The right and left front forks are installed symmetrically and therefore the removal procedure for one side is the same as that for the other side. Removal 1) Remove the front wheel assembly. Refer to “Front Wheel Assembly Removal and Installation in Section 2D (Page 2D-4)”. CAUTION ! •Make sure that the motorcycle is supported securely. •Do not operate the front brake lever with the front wheel removed. 2) Disconnect the brake hose clamp (1) from the front fender. 3) Disconnect the brake hose (2) from the brake hose clamp. 4) Remove the front fender by removing the bolts (3) , left and right. 5) Remove the reflex reflector for E-03, 24, 28, 33. 6) After removing of the headlight cover upper screws (4), move the headlight assembly forward. 7) Loose the front fork upper clamp bolt (5). NOTE •Slightly loosen the front fork cap bolt (6) to facilitate later disassembly. •Be sure to adjust the rebound damping force adjuster (7) to the softest position before removing the front fork. 8) Loosen the front fork lower clamp bolts (8) and remove the front fork. NOTE Hold the front fork by the hand to prevent sliding out of the steering stem. Installation 1) Set the front fork to the front fork lower bracket temporarily by tightening the lower clamp bolts (1) . 2) Tighten the front fork cap bolt (2) to the specified torque. Tightening torque Front fork cap bolt (a): 23 N·m (2.3 kgf-m, 16.5 lb-ft) 3) Loosen the lower clamp bolts. 4) Set the front fork with the upper surface “T” of the outer tube positioned 3.0 mm (0.12 in) “a” from the upper surface of the steering stem upper bracket. 5) Tighten the front fork lower clamp bolts (1). Tightening torque Front fork lower clamp bolt (b): 23 N·m (2.3 kgf- m, 16.5 lb-ft) 6) Tighten the front fork upper clamp bolt (3). Tightening torque Front fork upper clamp bolt (c): 23 N·m (2.3 kgf- m, 16.5 lb-ft

SUSPENSION SERVICE TOOLS/ FORK DAMPER ROD BLEED TOOL

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
33 SHOP EQUIPMENT & TOOLS SUSPENSION SERVICE TOOLS K&L FORK TUBE U-BLOCKS Precision machined from billet aluminum, these quality three piece sets are a handy, accurate and safe way to straighten and check fork tubes. 35-9411 36mm (for 33 thru 36mm tubes) 35-9412 40mm (for 37 thru 40mm tubes) 35-9413 43mm (for 41 thru 43mm tubes) 35-9414 46mm (for 44 thru 46mm tubes) 35-1964 35-8579 35-7995 DAMPER ROD HOLDERS Holds damper rod when disassembling forks. 35-8578 Yamaha front forks, 43mm Kayaba YZ125/250 (1988) YZ490 (88-90) 35-8579 Yamaha YZ125/250 with UD(upside down) forks FORK DAMPER ROD TOOLS Sold each. 35-7995 Combination Fork Damper Tool Designed to hold the damper rod during assembly & disassembly of Honda XR400′s or Suzuki DR-Z400S. One end features spanner type prongs for the XR400 and the other a 27mm hex for Suzuki. 35-1964 Combination Damper Rod Fork Tool Designed for assembly and disassembly of most inverted Kayaba and Showa 41mm, 43mm, 46, and 47mm forks. Use one end for Kayaba forks and the other for Showa forks. (not required for 91-92 Honda CR models) ROD HOLDER Double sided damper rod holder. Works on Kayaba U.D (upside down) 41mm forks. 35-8580 Yamaha YZ125/250Amodels (89-90) FRONT FORK CAP SOCKET Designed to remove and install Yamaha front fork caps with female hex head. Sold each. 35-8571 14mm female socket 35-8573 19mm female socket FORK DAMPER ROD HOLDERS Holds damper rod when disassembling and assembling front forks. 35-8576 Use for Yamaha 43mm Kayaba forks, 30mm hex YZ125 (84-87), YZ250 (81-87) IT250 (1983) YZ490 (82-87) 35-8577 Use for Yamaha 38mm Kayaba forks, 24mm hex YZ125 (81-83), IT175 (82-83), IT250 (81-82) YZ250 (77-80), YZ400 (77-79), IT465 (81-82) FORK CAP WRENCH Designed to remove the front fork caps on late model Honda CR’s and Suzuki RM’s. Can also be used for adjusting compression. One end of wrench is 49mm, the other is 50mm. Sold each. 35-7803 Fork Cap Wrench 35-8576 35-8577 35-8571 35-8573 6 Point Hex 35-8578

Incoming search terms:

Incoming search terms: