hydraulic pushrods for 1982 harley davidson

You search Auto repair manual PDF hydraulic pushrods for 1982 harley davidson, if there are search results will appear below. If search results do not exist, please search by others keyword.



  hydraulic pushrods for 1982 harley davidson Direct Download speed 5282 Kb/s

  hydraulic pushrods for 1982 harley davidson Full Version speed 6162 Kb/s



Harley-Davidson feuling Adjustable Pushrods Installation Instructions

0

Filed Under (Harley Davidson) by admin on 22-04-2012

download
1. Refer to the proper factory service manual for your model and year of engine, for removal of existing pushrods. 2. The Feuling pushrods are designed with a small adjustment parameter for rigidity creating maximum lift – These are not quick install pushrods and may require the removal of the lifter blocks and or loosing of the breathers/rocker arms supports. When loosening the rocker arm supports always remove the breather bolts first. 3. Clean and inspect each new Feuling pushrod including center oil hole 4. Feuling pushrods are marked Intake and Exhaust. The shorter pushrods are Intake and the longer pushrods Exhaust 5. Feuling recommends using new O-rings and gaskets where applicable to prevent oil leaks
6. Always pump up hydraulic lifters before installing them. Use an oil squirt can to fill the lifter with oil through the feed hole on the side of the lifter, push oil through the feed hole until the air bubbles are gone. If needed work the oil back and forth through the feed hole and pushrod seat with the squirt can. Light weight oil can be helpful. 7. Assemble and adjust one cylinder at a time, the servicing cylinder needs to be on TDC of compression stroke so the cam lobes are at their lowest point 8. Install pushrods into proper locations with the adjusting side of the pushrod down, towards the lifter. Slide the pushrods through the pushrod covers up into the rocker housing and set the pushrod on the seat of the lifter. We recommend filling the pushrods with oil then maneuver the pushrod up into the rocker arm seat. 9. Torque rocker arm housings and breathers to factory torque spec’s 10. See the instructions for your lifters for the proper adjustment. All Feuling hydraulic lifters run best at . 090″ – . 100″ of crush.

Harley-Davidson Twin Cam Engines Cam Chain Drive System Installation and removal MANUAL

0

Filed Under (Harley Davidson) by admin on 27-03-2012

download
Removing the Cam Chain Drive System. NOTES Changing camshafts and cam drives in the 2006-up Harley-Davidson® Twin Cam 88® engines is different than in pervious engines. Procedures require use • of some special tools. Installation should be done by an experienced mechanic with access to factory service manual and required tools. Tighten all fasteners to the correct specifications and in order described. Always use an accurate torque wench. • Incorrect installation can cause engine damage not covered under warranty. CAUTION Failure to install components correctly can result in sudden engine seizure. Engine seizure may result in serous injury to motorcycle operator, passenger, or others. A- Disconnect the battery ground cable to eliminate potential sparks and inadvertently engagement of the starter while working on the motorcycle. B- Remove spark plugs and pushrod cover clips. Collapse the pushrod covers to expose the pushrods. C- Safely elevate and stabilize the rear of the motorcycle. Place the transmission in high gear. Turn the rear wheel to rotate the engine until both lifters and pushrods for either cylinder are at the lowest point on the camshaft (TDC of compression stroke). Both intake and exhaust pushrods for that cylinder will be under pressure from the valve springs and will rotate with light finger pressure. NOTE: 510G camshafts may use stock style non-adjustable pushrods instead of adjustable pushrods. If installing non-adjustable pushrods, disassemble and assemble rocker boxes per H-D® instructions. All other S&S® gear driven cams require installing adjustable pushrods. As a time-saving measure, the stock pushrods can be removed with bolt cutters. Be sure to head caution and warnings of these instructions. D- Cut the pushrods for the cylinder that is at TDC with the bolt cutter and remove the pushrod covers from the engine. Rotate the engine to place the pushrods for the other cylinder at their lowest point. Cut and remove the remaining pushrods. WARNING CAUTION Cutting pushrods with a saw or cutoff wheel may result in debris entering the engine, causing engine damage not covered under warranty. WARNING Cutting pushrods without releasing spring pressure, by rotating the engine until tappets are at the lowest point of travel can result in bodily injury. E- Remove the pushrod covers and lifters form the crankcase. F- Remove engine cam cover and gasket. Secure lifers with a tool made from a large binder clip

Incoming search terms:

Harley Davidson HIGH PERFORMANCE QUICK- INSTALL ADJUSTABLE PUSHRODS INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Remove stock pushrods using a bolt cutter. 2. Place the motorcycle on a hydraulic center stand with the rear wheel raised off the ground. Remove spark plugs. CAUTION 1 WARNING 1 WARNING CAUTION 1 WARNING CAUTION ® i02097.tif Figure 1. Adjustable Push Rod Kit Number 17997-99A Pushrod Tube Adjusting Screw Flats Adjusting Screw Locknut 1 of 2 Exhaust Pushrod Tube has Thicker “Finished” area and is slightly longer Intake Pushrod Tube has Thinner “Finished” area and is slightly shorter 3. With transmission in gear use rear wheel to turn engine over until both front cylinder tappets are at their lowest point. 4. Replace O-rings, lower pushrod cover and spring cover keeper with new components supplied in kit. 5. See Figure 1. Loosen locknut on all of the pushrods and adjust them to their shortest length. NOTE See Figure 1. In Step 6, pushrods with the Thinner “Finished” area on the tubes must be installed to the Intake location on the cylinders; pushrods with the Thicker “Finished” area on the tubes are slightly longer and must be installed to the Exhaust locations on the cylinders. 6. Install pushrods with pushrod covers. Be sure adjuster end of pushrod is down and ball end of adjuster is in tappet socket. 7. If hydraulic tappets are used, adjust pushrods following procedure A. With solid tappets, follow procedure B. NOTE Pushrod adjustment must be made with engine cold. PROCEDUREA (Hydraulic Tappets) 1A. Adjust pushrod length to zero clearance. 2A. See Figure 1. With the pushrod tube kept from rotating with a 1/2 inch or adjustable wrench, slowly turn the adjusting screw with a 5/16 in. wrench, 2-1/2 complete turns counter clockwise (lengthening the pushrod) as viewed from the bottom. (You may wish to mark adjuster to aid in counting turns.) 3A. Hold adjusting screw and tighten locknut with 1/2 in. open end wrench against the pushrod tube. If pushrod turns with locknut use three open end wrenches, one to hold the pushrod tube, one to hold adjusting screw and one to turn locknut.

Incoming search terms:

Harley-Davidson Evolution Engines, Hydraulic Lifter Limited Travel Kit Installation Manual

0

Filed Under (Harley Davidson) by admin on 23-10-2010

download
Remove tappet assemblies from engine being sure that each one is kept with it’soriginal tappet block. NOTE: This procedure is the preferred method of installation. However, kit can be installed without removing lifters from engine. 2. Remove hydraulic piston retaining wire clip from one assembly at a time. Be careful not to bend wire clip during disassembly. 3. Completely disassemble tappet removing all parts. 4. Thoroughly clean all parts including tappet body. Remove any oil which might prevent hydraulic unit from fully collapsing during adjustment. 5. Insert one spacer from S&S HL 2 Tkit in tappet body. 6. Reassemble tappet in reverse order making sure original parts arereturned to their original positions. See Picture1. 7. Replace wire retaining clip in tappet body. 8. Put tappet back in original tappet block. 9. Repeat Steps 2 through 8 for three remaining tappets. 10. Reassemble engine with modified tappets. 11. Adjust pushrods. NOTE – In all cases engine must be cold and lifter must be at lowest point of travel for pushrod adjustment To prevent accidents, remove ground cable from battery. A. Remove spark plugs. B. Bring piston to TDC on compression stroke in cylinder to be adjusted. Normally both tappets will be at their lowest point of travel. C. Extend pushrod adjustment, collapsing lifter until piston assembly is in contact with HL 2 Tspacer and pushrod is tight. If tappets contain oil, as when pushrods are readjusted after engine has been run, or if all oil was not removed during installation, extend pushrod adjustment until valve is open (about five additional turns of adjusting screw). Allow 5 minutes for hydraulic unit to bleed down. If pushrod can be turned with fingers after bleeding down, lifter is not completely collapsed, and this step must be repeated. NOTE – perform this operation on one cylinder at a time. Do not turn engine until pushrod adjustment is complete. Turning engine while valve is held off the seat could result in valve to valve or valve to piston contact and serious valve train damage. D. Loosen pushrod adjustment until pushrod can be rotated with the fingers with slight drag. NOTE – Shortening adjuster an additional six flats or full turn from zero lash often results in quieter pushrod operation. This provides additional travel for the hydraulic piston assembly, which can improve the ability of the hydraulic unit to maintain zerolash under normal operating conditions. E. Tighten lock nut. F. Follow the same procedure for all four push rods. G. Recheck pushrod adjustment after a few hundred miles. NOTES ● It is a good idea to recheck pushrod adjustment in a new engine as valve train may tighten up due to gasket compression and valve seat wear. ● Upon initial start up after modification, HL 2 Tequipped lifters may be somewhat noisy for 10-20 miles. If lifters are still noisy after 20 miles it is recommended that pushrods be adjusted 1⁄2 turnlooser. See step D

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

2010 Harley-Davidson FLHR Road King front and rear 4-piston braking system Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
in Vivid Black with blue and silver pinstripes, six-speed. Air-cooled, Twin Cam 96™ engine with Electronic Sequential Port Fuel Injection (ESPFI), ABS, security system, cast wheels with independent front and rear 4-piston braking system. Motorcycle generously donated by Harley-Davidson Motor Company Police & Fleet Sales. MSRP excludes all taxes title/documentary fees, registration, tags, dealer prep, labor and installation charges, insurance, optional equipment and accessories, certificate of compliance or non-compliance fees, and finance charges. Delivery must be coordinated through Rockville Harley-Davidson by November 30, 2010. Winner is responsible for any applicable fees above. 6,000 tickets printed. Odds of winning are 1:6,000. Ticket holder need not be present to win. Licensed by the D.C. Lottery and Charitable Games Control Board. Must be 18 years or older to win. No substitutes, return for cash, or other models. As per IRS tax code, amounts paid for chances in a raffle do not qualify as a deductible charitable contribution. Taxes on prizes are the responsibility of the winner. Harley-Davidson is proud to be a sponsor of the National Law Enforcement Officers Memorial Fund. Harley-Davidson Motor Company is a prize provider only, and Harley-Davidson, Inc., and Harley-Davidson Motor Company have no responsibility regarding conduct or administration of the raffle.

Incoming search terms:

Harley Davidson Five Speed Transmissions Hydraulic Clutch Modification

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Hydraulic Clutch Modification for Harley Davidson With Champion Reverse Gear 1 1.1 Install Reverse Gear Assembly to gearbox. 1.2 Remove clutch cover (left side). 1.3 Remove Release Plate (clutch adjustment) and Push Rods. 1.4 Install Hydraulic Clutch Release Cover with supplied spacer and two gaskets. 1.5 Bleed clutch system. NOTE: When bleeding clutch system, lever feel will become hard, do not force lever because piston is at end of travel.(Continue Bleeding) 2 2.1 Install Push Rod. 2.2 Push the rod into clutch assembly to force hydraulic piston to its start position. Push the rod hard until the clutch cylinder is fully compressed. This is the start position. 2.3 Install Hydraulic Clutch Throw-Out Bearing Holder and bearing to push rod. Do not install circlip at this time. 2.4 If the throw-out bearing holder does not fully seat into the Pressure Plate (Figure 2.4), proceed to step 2.5. If shaft is too short then use throw-out bearing holder from Champion Reverse Gear Kit, skip next step and proceed to 3.0 2.5 Measure distance between bearing holder and pressure plate (ensure that push rod is pushed in) Figure 2.4 2.6 Remove bearing holder and push rod, reinstall bearing holder until seated (without push rod). Measure distance from pressure plate to bearing holder. Figure 2.6 2.7 Add measurements taken in steps 2.5 and 2.6 2.8 Add 0.090″ to total of step 2.7 (allowance for clutch plate wear). Measurement should be approximately 1/8″. 2.9 Measure push rod length. 2.10 Subtract measurement of step 2.8 from measurement of step 2.9 (push rod length). This measurement represents the amount of material to be removed from ball end of push rod. (Step 2.11)

Incoming search terms:

HARLEY DAVIDSON CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
CHROME 1.25 INCH (31.75 MM) DIAMETER HANDLEBAR KIT GENERAL Kit Number 56032-08 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only). This kit does not fit models equipped with a hydraulic clutch, handlebar mounted gauges or the Road Tech® Radio. Additional Parts or Accessories Required Separate purchase of additional parts or accessories is required for proper installation of this Handlebar Kit on this model motorcycle. Please see the P&A retail catalog or the Parts and Accessories section of for a list of required parts or accessories for this model. For Australia, Brazil, England, Europe and Japan, two special screws (Part Number 2935A) will also be required. Tools and Supplies Required Loctite® 271 Threadlocker and Sealant – Red (H-D Part Number 99671-97) is required for the proper installation of this kit. Fresh, uncontaminated DOT 4 brake fluid from a sealed container will also be needed. Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) For models that retain the original brake line, the two brake- line gaskets found at each banjo fitting must be replaced . Refer to the appropriate parts catalog or see a Harley-Davidson dealer for the correct part numbers. Motorcycles equipped with a glued left-side hand grip will also require a new grip, sold separately. Refer to the parts catalog for replacement stock hand grips. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory hand grips that are available. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for this year and model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 6 and Table 1. INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills)

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
FL Touring models equipped with a TLE/ TLE Ultra Sidecar will require the additional installation of a Bank Angle Switch Kit (88115-03) and is available for separate purchase. See a Harley-Davidson dealer.INSTALLATION 1. Remove the original equipment (OE) Turn Signal Module (TSM) or Body Control Module (BCM) following the instructions in the service manual. 2. Install the Bank Angle Sensor (BAS) on sidecar vehicles. 3. Install the new turn signal/security module (TSSM) (7), Hands Free Security Module (HFSM) (1) or BCM (9, 11) from this kit, following the instructions in the service manual. Configure the Trike or sidecar TSSM, HFSM or BCM to “Side Car Enabled” using Digital Technician. 4. Install the Hands Free Security Module (HFSM) Antenna and antenna mount (6) if necessary, using the service manual instructions. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) ACTUATION 1. See a Harley-Davidson dealer to activate the key fob to the TSSM, HFSM or BCM. NOTE You can activate the TSSM fob by referring to the procedure in the electrical diagnostic manual. TRIKE AND SIDECAR CONFIGURATION (FL TOURING MODELS ONLY) Only Touring Harley-Davidson Motorcycles are suitable for sidecar use. Consult a Harley-Davidson dealer. Use of motorcycles other than Touring models with sidecars could result in death or serious injury. (00040a) NOTES FL Touring Models equipped with TLE/TLE-Ultra Sidecar require the installation of a Bank Angle Sensor (88115-03). Failure to install and configure a Bank Angle Sensor may result in death or serious injury. Sidecar and Trike configuration of the security system requires the use of a Digital Technician. Consult your Harley-Davidson dealer or the sidecar or Trike service manual for complete details. On vehicles equipped with a sidecar, the security system must be reconfigured from the default solo vehicle setting to the sidecar setting

Incoming search terms:

HARLEY DAVIDSON FRONT TYPHOON WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
If installing kit 44615-08, 40774-10, 44657-08 or 43300053 on a Dyna model with stock laced wheels, the separate purchase of stock brake disc (44553-06A) or polished brake disc (41500012) is required. The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) •Harley® Preserve™ Bare Aluminum Protectant (99845-07) Touch-up paint for painted wheels is available from a Harley- Davidson dealer: •Touch-Up pen, wheel, black (94482) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. 1 2 is06470 1. Closed brake disc 2. Open brake disc or floating rotor Figure 1. Front Brake Disc Styles Table 1. Front Disc Hardware Fitment Hardware Brake Disc 5 Stock disc screws (3655A) Closed disc Chrome screw kit (46646-05) includes 5 screws 5 Stock disc screws (3762M) and 5 disc washers (6966M) Open disc NOTE: Models equipped with dual front brakes and models being equipped with a wheel with dual brake mounting surfaces require twice as many screws/washers (10 total screws or 2 chrome screw kits if available). INSTALLATION NOTE Use plastic protectors on tire mounting tools and rim clamps when mounting a tire to a painted wheel. For wide low profile tires a tire mounting machine with a second arm to press down on the sidewall while the wheel is rotating is recommended.