idle control harley

You search Auto repair manual PDF idle control harley, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be installed in the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3 2 1 is00825 1. Brake lever 2.5/32 inch (4 mm) cardboard insert 3. Brake lever bracket Figure 1. Install Cardboard Insert 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 3 4 1 2 5 is 02071 1. Upper switch housing 2. Lower switch housing 3. Throttle cable adjuster 4. Idle cable adjuster 5. Adjuster jam nut Figure 2. Handlebar Throttle Control 4. Remove the right upper and lower switch housing screws. 5. Loosen the upper screw securing the handlebar clamp to the master cylinder housing. Remove the lower clamp screw and flat washer. NOTE If possible, leave the friction shoe in place. The friction shoe is a loose-fit and may fall out or become dislodged if the lower switch housing is turned upside down or shaken. 6. See Figure 3. Remove the brass ferrules from the notches on the inboard side of the throttle control grip. Remove the ferrules from the cable end fittings. 1 2 4 3 is 02072 1. Throttle cable 2. Idle cable 3. Brass ferrule 4. Notch Figure 3. Throttle/Idle Control Cables 7. Pull the crimped inserts at the end of the throttle and idle control cable housings from the lower switch housing. For best results, use a rocking motion while pulling. Remove cables with retaining rings from switch housing. Apply a drop of light oil on the retaining ring, if necessary, to help in removal. NOTE If installing different handlebars, measure the change in distance that will be required from the end of the cable housing to the throttle grip. Compare this additional required length to the cables provided in the kit. If the cables are more than 2.0 inches (51 mm) longer or more than 1.0 inch (25 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. Install proper length throttle cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00396b) 8. Follow instructions in the applicable service manual and remove air cleaner and backplate.

Incoming search terms:

Yamaha Road Star Forward Control Kit Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Before starting to assemble this forward kit on your motorcycle check the packing list to make sure that the kit you received is the correct one for your model motorcycle and that the foot pegs are the style you ordered (billet or ISO). Next check the contents hardware kit P.N.0109-1000 against the packing list for completeness. Installing The Shift Control Photo 1 Remove wires from horn. Remove the two hex head bolts (Save for later installation) that mount the OEM shift controls to your motorcycle. Unthread stock shift rod at trans shift arm, leaving OEM rod end connected to stock shift arm. Using Original Metric hardware, place a drop of Loctite #242 (blue) to the bolt threads and mount the shift control plate to the motorcycle frame, Photo 2. FORWARD CONTROL KIT PM SHIFT CONTROL ASSEMBLY Note Before torquing the shift control mounting bolts down, tighten them snug and look behind the shift control mounting plate to where it contacts the mounting lug on the frame. Make sure it fits squarely to the lug before proceeding further. Torque the two shift control mounting bolts down to 25 ft-lb. Using a 3/8″ x 1″ hex head bolt with a lock and flat washer put a drop of Loctite #242 (blue) on the threads and insert the bolt through the rear of the control mounting plate and attach the foot-peg pivot to it. Tighten the bolt while holding the footpeg pivot so that its hinge is lined up in a 45˚ rear facing angle. Thread supplied shift rod coupler to stock shift rod end at trans arm. Mount the shift pedal to the other end of the shift ro d using a 5/16″ x 1″ socket head screw and Nylocnut . Adjust the transmission shift linkage so that the shift arm on the forward controls and the shift arm on the transmission are parallel. Secure it with the jam nuts. Apply a drop of Loctite #242 (blue) to the threads under the jam nut before tightening see Photo 3 After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use. A Shim Washer PHOTO 4 A B C D PHOTO 5 A PHOTO 6 PHOTO 7 Note For complete brake system removal instructions and precau – tions refer to the appropriate service manual for your year and model motorcycle

Incoming search terms:

SUZUKI SV1000S EMISSION CONTROL INFORMATION/ SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
EMISSION CONTROL SYSTEMS FUEL INJECTION SYSTEM SV1000S motorcycles are equipped with a fuel injection system for emission level control. This fuel injection system is precision designed, manufactured and adjusted to comply with the applicable emission limits. BEFORE-PRESSURIZED FUEL PRESSURIZED FUEL * I’ RELIEVED FUEL ~%~~~ Ift 0 0 9 0 0 0 EMISSION CONTROL INFORMATION 9-3 CRANKCASE EMISSION CONTROL SYSTEM The engine is equipped with a PCV system . Blow-by gas in the engine is constantly drawn into the crankcase, which is returned to the combustion chamber through the breather hose, air cleaner and throttle body . C * FRESH AIR FUEL/AIR MIXTURE 411111110 BLOW-BY GAS 9-4 EMISSION CONTROL INFORMATION EXHAUST EMISSION CONTROL SYSTEM (PAIR SYSTEM) The exhaust emission control system is composed of the PAIR system and THREE-WAY CATALYST system. The fresh air is drawn into the exhaust port with the PAIR solenoid valve and PAIR reed valve . The PAIR solenoid valve is operated by the ECM, and the fresh air flow is controlled according to the TPS, ECTS, IATS, ZAPS and CKPS. H02 sensor (Except for USA) I 0 0 0 0 0 NOISE EMISSION CONTROL SYSTEM TAMPERING WITH THE NOISE CONTROL SYSTEM PROHIBITED : Federal law prohibits the following acts or the causing thereof: 1. The removal or rendering inoperative by any person, other than for purposes of maintenance, repair or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use, or 2. The use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW : • * Removing or puncturing the muffler, baffles, header pipes, screen type spark arrester (if equipped) or any other component which conducts exhaust gases . • * Removing or puncturing the air cleaner case, air cleaner cover, baffles or any other component which conducts intake air . • * Replacing the exhaust system or muffler with a system or muffler not marked with the same model specific code as the code listed on the Motorcycle Noise Emission Control Information label . EVAPORATIVE EMISSION CONTROL SYSTEM (FOR E-33)

Incoming search terms:

Harley-Davidson MOBILE RADIO & CONTROL UNIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-03-2012

download
Installation of the ORION mobile radio and control unit consists of: •Assembling and installing the weather resistant motorcycle case assembly, including the adapter bracket, case/antenna mounting bracket, and bottom case (previously assembled) to the motorcycle mounting bracket (user supplied). •Installing the radio in the radio mounting bracket located inside the weather-resistant case, •Installing the control unit, microphone, and speaker •Installing the antenna •Routing the power, control, and option cables •Connecting all cables including: power, control, and option cables. •Installing the Headset Option •Operational check All mounting hardware consists of stainless steel screws, locknuts, nuts, and lockwashers to resist corrosion. TOOLS REQUIRED •Socket wrench set U.S./metric with 3″ extender •Open end wrench, adjustable •Wire clippers •TORX BIT set, small metric 13
EQUIPMENT INSTALLATION Assembling & Installing The Weather Resistant Case As- sembly The motorcycle Weather Resistant Case Assembly may be installed on almost any motorcycle. Installation instructions provided here include information for the Harley-Davidson Dyna and Road King models and the Kawasaki K1000. Figure 5 illustrates installation on Harley-Davidson motorcycles while Figure 6 illustrates installation on a Kawasaki K1000. Refer to these diagrams during installation. Installation on other motorcycles is at the discretion of the installer. Harley-Davidson Installation 1. Unpack the weather resistant motorcycle case, remove the key taped to the top cover and open the case. 2. Refer to Figure 5 and verify that all components shown in the diagram are available. 3. Mount the adapter bracket onto the Dyna or Road King radio mounting bracket (user supplied) using the 1/4-20 x 5/8 screws provided

Incoming search terms:

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

harley davidson CRUISE CONTROL KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 23-02-2012

download
See Figure 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 5. Refer to the service manual, and follow the instructions to loosen the brake hand lever/master cylinder assembly and remove the right-side upper and lower switch housing sub-assemblies from the handlebar. It is not necessary to remove the throttle control grip. For FLHR models: Refer to the service manual. Disconnect the left-side handlebar MOLEX socket housing from the gray eight-way main harness pin housing [24B] inside the headlamp nacelle. Refer to the service manual to remove the clutch hand lever and left-side upper and lower switch housing subassemblies from the handlebar. 6. For ALL models: See Figure 2. The friction shoe (1) is a loose fit on the end of the tension adjuster screw (2). Make sure the shoe has been removed with the switch housing sub-assemblies, and is not lodged in the groove of the throttle control grip (4). 3 4 1 2 is06318 1. Friction shoe 2. Tension adjuster screw 3. Right-side lower switch housing 4. Throttle control grip Figure 2. Throttle Tension Adjuster Screw and Friction Shoe 7. See Figure 1. Verify that the 5/32-inch (4 mm) thick insert is in place between the brake lever and the lever bracket. Obtain the new right-side handlebar switch housing assembly (Item 4 or 5, depending on model) from the kit. Separate the upper and lower halves of the housing assembly. Refer to the service manual, and follow the instructions to install the switch housing assembly and brake hand lever/master cylinder assembly to the handlebar. 8. Route the right-side switch harness along the same path as the original harness (along the right handlebar). Connect the pin housing to the black socket housing disconnected in Step 3. 9. For FLHT, FLHTC, FLHX, FLHXXX and FLTRX models: Continue at Step 11. For FLHR models: Obtain the new left-side switch housing assembly (6) from the kit. Separate the upper and lower halves of the switch housing assembly. Refer to the service manual, and follow the instructions to install the left-side switch housing assembly and clutch hand lever assembly to the handlebar. 10. Route the left-side hand control harness along the same path as the original harness (along the left handlebar). Connect the pin housing to the gray socket housing disconnected in Step 5

HARLEY DAVIDSON HAND CONTROL LEVER KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Dav- idson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) Brake Lever Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) NOTE Do not remove handlebar clamp or switch housing assembly to remove brake lever. 1. See Figure 3. Remove the retaining ring (4) from the groove in the pivot pin (A). Do not position fingers between hand control lever and handlebar grip. Improper hand positioning can impair control lever operation and cause loss of vehicle control, which could result in death or serious injury. (00032a) 2. Place a 4 mm (5/32-inch) thick insert between the brake lever and the lever bracket. NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 1. 3. See Figure 3. Loosen the brake master cylinder clamp screws. Rotate the master cylinder assembly slightly forward and then slide toward the center of the handlebar. 4. Remove the pivot pin (A) and original equipment (OE) brake lever. Retain the pivot pin for later assembly. 5. Apply a small amount of GM-40M grease (H-D Part No. 42820-04) to the area where the master cylinder pushrod seats against the brake lever. DO NOT apply grease to the stop-light switch contact surface of the lever. See Figure 2. Align the hole in the brake hand lever with the hole in the master cylinder bracket. From the top of the assembly, slide the pivot pin down through the bracket and hand lever. Check that the pushrod (1) is properly seated in the bowl shaped tab (2) on the lever

HARLEY DAVIDSON XL CHROME FORWARD CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
2008-05-05 XL CHROME FORWARD CONTROL KIT GENERAL Kit Number 33395-04, 33398-04 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harley- davidson.com (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 5, Figure 6 and Table 1. INSTALLATION Remove Stock Shift Lever and Footrest Assembly 1. See Figure 1. Loosen the shift lever retaining screw (2) securing the shift lever (1) to the shifter shaft. Slide the shift lever off the splined shaft. Remove shifter peg from lever and save for installation. Discard shift lever. 2. Remove the two socket head screws (4) securing the footrest bracket (3) to the frame and remove footrest. Discard screws. 3. See Figure 5. Obtain two hole plugs (1) from kit and firmly press plugs into frame screw holes remaining from footrest removal. 4. See Figure 2. Remove the retaining ring (1) from the clevis to free the footrest clevis pin (4). Remove the clevis pin and footrest (3) from the footrest support. Save footrest for installation. Discard retaining ring, clevis pin, spring washer and footrest bracket. 1 2 4 3 is 01887 1. Shift lever 2. Retaining screw 3. Footrest bracket 4. Socket head screw Figure 1. Remove Shift Lever and Footrest 5 1 3 2 4 is 01901 1. Retaining ring 2. Spring washer 3. Footrest 4. Clevis pin 5. Footrest bracket Figure 2. Remove Left Footrest from Support Remove Stock Brake Pedal and Footrest Assembly 1. See Figure 3. At the right footrest, remove the retaining ring (1) clevis pin (2), footrest (3) and spring washer (4). Discard all hardware but save footrest for installation. 2. Remove brake rod (5) from brake pedal and master cylinder bell crank. Discard brake rod. 3. Remove the two screws (6) and right footrest/brake pedal support bracket with attached brake assembly from frame

HARLEY DAVIDSON CRUISE CONTROL KIT FOR FLHR/I AND FLHRS/I MODELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Remove seat, left saddlebag, left side cover and air cleaner assembly following instructions in applicable Service Manual. 2. Review the CRUISE CONTROL-ULTRA MODELS section in the applicable Service Manual before attempting to install this kit. Install Cruise Control Module To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the appropriate Service Manual and remove bat- tery. 1 is04799 1. Cruise control module mounting hole (3) Figure 1. Battery Box (Right Side View) 2. See Figure 1. In battery box, identify the location of the three mounting holes (1) (on left side of panel) for mounting the cruise control module. 3. See Figure 10. Obtain the cruise control module (1) with cruise cable attached and three grommets (5) from kit. Install the grommets on studs of cruise control module with small diameters outward. 4. See Figure 2. While holding cruise control assembly in place near its mounting location, feed the cruise control cable through the hole in frame crossmember plate and route under rear spark plug wire staying on inner side of fuel line components. Carefully curve cable toward the right and continue routing up under the fuel tank and over the top of the engine stabilizer bracket, then down between cylinder heads. Leave in place temporarily. 5. See Figure 10 and obtain a harness retainer (4) from kit and secure the cruise cable to crossmember plate with barb as shown. On California models, remove the EVAP hose from cable clip and secure hose with one of the cable strap (8)

Incoming search terms:

Incoming search terms: