importers exporters dealers of iron metalworks steel chemical equipment mail

You search Auto repair manual PDF importers exporters dealers of iron metalworks steel chemical equipment mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





TOYOTA ALL MODELS IRON PARTICLE CONTAMINATION REPAIR

0

Filed Under (Toyota Manuals) by admin on 28-10-2011

download
During rail transportation or extended storage near industrial areas, vehicles may occasionally be subjected to contamination by airborne iron particles shed from either railroad tracks, train wheels, etc., or exposure to heavy machinery facilities. These particles can adhere to horizontal painted surfaces of vehicles and quickly corrode when combined with moisture. If not immediately recognized and removed from painted surfaces, they become embedded and cause further paint damage. INSPECTION: This type of contamination can be identified by the presence of small red or brown particles on the paint surfaces. These particles are often difficult to see on dark color paints, but still can be readily felt when brushing a hand or fingernail across horizontal body surfaces such as hood, roof, or decklid. CAUTION: Because of the abrasiveness of these small iron particles, polishing or buffing procedures should not be attempted to repair the paint surface of an affected vehicle. This will result in further paint damage and detract from vehicle appearance. CORRECTIVE ACTION: Washing the affected paint surfaces with an oxalic acid solution is the recommended method to dislodge embedded iron particles and remove the surrounding rust stains. ZEP X-20472 “INDUSTRIAL FALLOUT REMOVER” is one of several commercially pre-mixed oxalic acid wash solutions and is very effective in removing iron particle contamination. The correct usage of oxalic acid solutions is described in this bulletin

Incoming search terms:

HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

INDIAN MOTORCYCLE EQUIPMENT LISTING

0

Filed Under (Indian) by admin on 28-11-2010

download
INDIAN MOTORCYCLE, INC. EQUIPMENT LISTING QTY DESCRIPTION SERIAL # 1 VIPER VT-25 CNC LATHE FANUC 18-T CONTROL MACHINE CENTER 3398080101 1 MIGHTY COMET MILLING 3VHG 98017/98025 1 SHARP MILL PACKAGE LMV 9 X 42 61124334/61124335/31124336 1 VIPER V-1000G CNC MILL MDL VMC 206506 1 CLAUSING C12AX KHS BANDSAW INV328172 LC889967 1 CNC ROTARY HYDRAULIC TUBE BENDING MACHINE – HMT 992L3055 3 AXIS 005B 1 JANCY COLD SAW T315 21006 1 KALAMAZOO AH9W BANDSAW GEI TECHNOLOGY SOLIDWORKS & PDM WORKS, EASTMAN M9000 STATIC TABLE SYSTEM 1 MITUTOYO CORDINATE MEASURING MACHINE 1006804 2 KHS JET DRILL PRESS 2 MOTOMAN -SK16 ROBOT S99354/S994351 LOT TENNESSEE RAND – SCOUT SWING ARM MANUAL WELD FIXTURE, CHIEF SWING ARM MANUAL WELD FIXTURE, SCOUT REAR STRUT MANUAL WELD FIXTURES, CHIEF REAR STRUT MANUAL WELD FIXTURE, ERGONOMIC TOUCH UP AND REPAIR STANDS – BOTH CHIEF & SCOUT INDIAN MOTORCYCLE, INC. EQUIPMENT LISTING QTY DESCRIPTION SERIAL # 1 CROWN FORKLIFT SC4040-35 ISLE PICKER TROJAN BATTERY HOBART CHARGER FORKLIFT – SC4040-35 BATTERY 63257 CHARGER 100C62388 1 CROWN FORKLIFT SP3210-210 1 NISSAN ELECTRIC FORKLIFT – MODEL PE30Y CSPO1-9A1555 1 NISSAN ELECTRIC FORKLIFT – MODEL PE50YSC CWPO2-9C2180 1 NISSAN LIFT TRUCK MODEL P50LP – USED KP50YLP-901370 CROWN FORKLIFT ISLE PICKER 1A206705 KOMUTSU FORKLIFT 506718A 2000 CHEVY FLATBED

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

2007 Harley-Davidson Softail Family Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
frame Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Swingarm Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Front Fork 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers Rear Shocks Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Caliper Type 4-piston front and rear 4-piston front and rear 4-piston front and rear Rotor Type: (diameter x width) Patented, uniform expansion rotors Patented, uniform expansion rotors Patented, uniform expansion rotors Front 292 mm x 5.08 mm 292 mm x 5.08 mm 292 mm x 5.08 mm Rear 292 mm x 5.84 mm 292 mm x 5.84 mm 292 mm x 5.84 mm Front (mm) 130 130 130 Rear (mm) 109 109 109 Engine Torque (EU standard EC95/1)5 86 ft. lb / 117 Nm @ 3200 rpm 89 ft. lb / 120 Nm @ 3300 rpm 89 ft. lb / 120 Nm @ 3300 rpm Right 29° 30° 28° Left 26° 28° 26° Battery Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating ) Charging Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Starting 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement Headlamp Headlamp Headlamp Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Tail/Stop Lights Tail/Stop Lights Tail/Stop Lights 8W/28W (5W/21W) 8W/28W (5W/21W) 8W/28W (5W/21W) Turn Signal Lights Turn Signal Lights Turn Signal Lights 28W (21W) self-canceling 28W (21W) self-canceling 28W (21W) self-canceling Indicator Lamps Indicator Lamps Indicator Lamps High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6- speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings Passing Lamps Chrome Vivid Black Vivid Black Vivid Black Black Cherry Pearl Black Cherry Pearl Black Cherry Pearl Deep Cobalt Pearl Black Pearl Black Pearl Pewter Pearl Fire Red Pearl Deep Cobalt Pearl White Gold Pearl Deep Cobalt Pearl Olive Pearl & Vivid Black Suede Blue Pearl & Vivid Black Suede Blue Pearl White Gold Pearl & Vivid Black Black Cherry Pearl & Pewter Pearl Olive Pearl White Gold Pearl & Deep Cobalt Pearl Fire Red Pearl & Black Pearl Pacific Blue Pearl Deep Cobalt Pearl & Pewter Pearl Pewter Pearl Yellow Pearl White Gold Pearl

Incoming search terms:

DUCATI EVOLUZIONE SLIPPER CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
If installing with Ducati OEM basket you need the washer cod. 0D1SR140C220045 (3mm). – If installing with STM basket (Z12 o Z48) you need the washer cod. 001MG019 (1,5mm). – Insert the correct washer on the gear shaft. – Perform the initial hub group assembly: position the progressive engagement steel plate (003MG015) on the hub (0F3SR140J24001C) , with the step facing up. Be careful to position it correctly into the specific seats, then check that pushing one side, the opposite stand up simultaneously. – Now put the 6 steel balls (001MG025) at the bottom of the grooves using a little bit of grease. Then fix the clutch drum (0F3SR140J24002C) on the clutch hub (0F3SR140J24001C) at rest position, using an M6 screw to help locking the two parts, avoiding in this way any possibility for the steel balls (001MG025) to fall out while inserting the hub pack on the main shaft. – Insert the hub pack on the gear shaft – Insert the clutch discs starting with the sintered one and finishing with the steel guided one; total disc set thickness must be included between 36 and 36,5mm. – Remove the M6 screw from the hub (0F3SR140J24001C). – Put the drum stopper hub (003MG106) on the hub (0F3SR140J24001C). – Verify that the secondary spring support (0F3SR540B140016) is well inserted into its housing on the drum (0F3SR140J24002C). – Insert the secondary spring (0S2085) into its housing on the drum (0F3SR140J24002C). – Mount the pressure plate (003MGP10) on the drum (0F3SR140J24002C) . – Position the Evoluzione spring (0S1090) on the pressure plate (003MGP10), with the convex part facing up (STM logo facing up), making sure previously that the squared section ring (901SE003), which works as primary spring support, is well positioned into the pressure plate itself. – Assemble the complete spring stopper pack: starting from the spring stopper plate (003MG008), with the shaped side facing up as shown in the picture. Insert the ball bearing (003MG007) and finally the spring stopper hub (0F3SR140N220007). Once completed these operations, position the complete spring stopper pack inside the Evoluzione spring (0S1090). – Insert the toothed washer (901RD101) with the convex side facing up, then insert and tighten up the clutch nut (0F30S140C220013); use a dynamometric wrench setting the torque suggested by the bike manufacturer. We suggest to use the specific optional tool (UTL-0020) in order to lock the pressure plate (003MGP10) while performing this operation. – Assemble the complete bearing rest pack: insert the washer (001MG018) in its housing on the bearing rest (0F3SR140N220004). Then put in the same housing the ball bearing and the push rod pin of the original clutch. – Position the complete bearing rest pack in the pressure plate (003MGP10), making sure it fits correctly into the housing grooves. – Manually practise a little pressure on the bearing rest (0F3SR140N220004) in order to release the seat for the tightness circlip (003MG018). – Fit correctly the above mentioned tightness circlip (003MG018). MAKE SURE that it adheres to all the groove perimeter. NB: Once completed the installation, repeatedly operate the clutch lever, checking that the pressure plate performs correctly the opening and closing movements. For a road use of the clutch you have to check clutch plates set every 2000 km. Please verify that the clutch plates set thickness is between 36,5mm and 35,0mm. If it is inferior to 35,0mm please replace a 1,5 steel plate with a 2 mm steel plate. For a racing use of the clutch we suggest to check the clutch plates set thickness frequently. GENERAL SAFETY REGULATIONS – In this sheet are reported the directions to perform correctly the clutch assembly operations. – STM reserves the right – without notice – to introduce any technical change whenever deemed it to be necessary to improve functionality and quality of the products. – Assembly operations must be performed by a skilled technician and must be scrupulously observed. – Before mounting the clutch make a complete inspection of the various parts, in order to verify the possible presence of faults or anomalies on the motorbike. – Make sure that there are no missing/damaged parts in the package . – Some parts of the clutch and its components can have sharp surface: handle with care. – Some components of the clutch, because of their small dimensions can be swallowed: keep away from children. STRADA srl Via Campo Archero 20 10023 Chieri ( TO ) Tel +39 011 9422832 Fax +39 011 9471447 003 MG 018 Tightness circlip

TOYOTA Tacoma 2005 – STAINLESS STEEL EXHAUST TIP Procedure

0

Filed Under (Toyota Manuals) by admin on 18-10-2011

download
Safety (eye protection, rechecking torque procedure, etc.).  Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).  Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Installation. (a) Make sure the vehicle’s tail pipe is free from dirt and debris. (b) Remove exhaust tip from box and set on a soft surface to prevent scratching. (c) Slide the Stainless Steel clamp over the vehicle tailpipe as shown. (Fig 1-1 & 1-2) (1) Locate the bolt of the clamp on the right side (3:00 Position) with the nut on the top as shown. (Fig 1-1) (2) Continue sliding up out of the way so it won’t interfere when you install the exhaust tip and aluminum bushing. (Fig. 1-2) (d) Slide the exhaust tip over the tail pipe with the bump facing toward the rear of the vehicle as shown. (Fig 1-3) (1) If necessary, a rubber mallet may be used to aid installation

PIAGGIO Power Program with SIP Stainless Steel Joint Pipe Installation Manual

0

Filed Under (Piaggio) by admin on 28-10-2010

download
First, loosen and remove both screws between joint pipe and exhaust. Then, remove the other two upper screws, as in illustration 2, between cylinder and joint pipe. This may be a little difficult to reach. For additional ease removing screws, raise up motor frame with a crowbar or chisel. Now, remove old joint pipe and replace with SIP stainless steel pipe. Don’t forget to replace old gaskets with new gaskets, included in delivery. Join us in the SIP Article Forum for further handy tips and tricks from those in the know at www.sip-scootershop.com Turn down screws bit by bit, one after another, to ensure balanced fit, making sure to loosen muffler screws shortly. If you should have difficulty getting a good fit, here’s a tip: drill longer holes on exhaust flange to get better adjustment. Finito; put away the tools and take a test drive

Incoming search terms:

Harley-Davidson Camshaft TC, EVO, Shovelhead, XL EVO, Iron Head, XR Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
EVO Black Widow PP8833-2 – 29 55 62 25 264 267 54 103 109 105.8 0.600 0.602 EVO Black Widow PP8826-2 – 27 61 63 29 268 272 56 107 107 107.0 0.602 0.602 EVO Black Widow PP8817-2 – 254 254 0.590 0.590 EVO Carl’s Speed Shop CM4 – 28 44 52 20 252 252 48 98 106 102.0 0.495 0.495 EVO Carl’s Speed Shop CM495F Y 19 47 50 16 246 246 35 104 107 105.5 0.495 0.495 0.179 0.168 EVO Carl’s Speed Shop CM580 – 19 47 50 16 246 246 35 104 107 105.5 0.580 0.580 0.194 0.163 EVO Carl’s Speed Shop CM612 – 36 60 68 28 276 276 64 102 110 106.0 0.612 0.612 0.277 0.235 88 EVO Carl’s Speed Shop CM660 – 38 62 68 28 280 276 66 102 110 106.0 0.660 0.660 0.314 0.277 90 EVO Carl’s Speed Shop CM774 – 284 284 0.784 0.784 0.277 0.236 EVO Carl’s Speed Shop CM780F – 34 70 74 30 284 284 64 108 112 110.0 0.774 0.774 103 EVO Crane EVR0020 – 31 64.5 77 23 275 280 54 107 117 112.0 0.608 0.589 88 EVO Crane Fireball 2000 Y -12 22 20 -10 190 190 -22 107 105 106.0 0.490 0.490 0.026 0.032 EVO Crane Fireball 300 Y 12 34 41 15 226 236 27 101 103 102.0 0.490 0.490 4000 EVO Crane Fireball 310 Y 16 40 43 19 236 242 35 102 102 102.0 0.490 0.490 1500 4500 75 EVO Crane Fireball 316 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 2000 5000 80 EVO Crane Fireball 326 – 24 48 57 25 252 262 49 102 106 104.0 0.490 0.500 2500 5500 EVO Crane H286 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 2000 5000 80 EVO Crane H290 – 17 43 45 23 240 248 40 103 101 102.0 0.581 0.581 1800 5200 EVO Crane H296 – 24 48 57 25 252 262 49 102 106 104.0 0.490 0.500 2500 5500 EVO Crane H304 – 24 50 55 25 254 260 49 103 105 104.0 0.600 0.600 2500 5800 EVO Crane H306 – 28 54 69 23 262 272 51 103 113 108.0 0.500 0.510 0.224 0.195 3000 6000 EVO Crane H310 – 23 63 68 28 266 276 51 110 110 110.0 0.550 0.550 0.229 0.229 3000 6500 88 EVO Crane H314 – 26 54 65 21 260 266 47 104 112 108.0 0.600 0.600 2800 6000 EVO Crane HEV0042 – 27 59 71 23 266 274 50 106 114 110.0 0.600 0.576 0.226 0.194 3000 6000 100 116 EVO Crane HEV0067 – 24 50 56 24 254 260 48 103 106 104.5 0.600 0.530 0.128 0.113 EVO Crane HEV0098 – 36 62 72 34 278 286 70 103 109 106.0 0.650 0.650 0.171 0.156 96 EVO CycleRama CR-E550 – 24 52 53 23 256 256 47 104 105 104.5 0.550 0.530 EVO CycleRama CR-E581 – 22 46 53 23 248 256 45 102 105 103.5 0.581 0.550 EVO CycleRama CR-E600A – 24 50 56 24 254 260 48 103 106 104.5 0.600 0.530 EVO CycleRama CR-E600B – 23 51 54 22 254 256 45 104 106 105.0 0.600 0.550 EVO CycleRama CR-E617 – 22 50 50 22 252 252 44 104 104 104.0 0.617 0.617 EVO CycleRama CR-E630 – 18 60 63 13 258 256 31 111 115 113.0 0.630 0.630 EVO CycleRama CR-E660 – 27 59 71 23 266 274 50 106 114 110.0 0.660 0.660 3500 6500 140 EVO Dave Mackie DM500 Y 22 38 52 12 240 244 34 98 110 104.0 0.500 0.500 0.189 0.138 EVO Dave Mackie DM500X Y 25 40 55 20 245 255 45 98 108 102.5 0.500 0.500 0.208 0.178 EVO Dave Mackie DM530 – 28 42 55 15 250 250 43 97 110 103.5 0.530 0.530 0.221 0.141 EVO Dave Mackie DM580 – 26 42 56 12 248 248 38 98 112 105.0 0.580 0.580 0.227 0.144 113 EVO Dave Mackie DM581 – 26 42 56 12 248 248 38 98 112 105.0 0.580 0.580 0.227 0.144 EVO Dave Mackie DM595 – 21 49 57 14 250 251 35 104 112 107.8 0.595 0.595 0.192 0.150 EVO Dave Mackie DM635 – 20 56 59 18 256 257 38 108 111 109.3 0.635 0.635 0.194 0.176 EVO Edlebrock 1740 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 0.176 0.203 EVO Edlebrock 1741 – 20 46 52 22 246 254 42 103 105 104.0 0.600 0.600 0.183 0.187 EVO Head Quarters HQ-23 – 19 47 52 24 246 256 43 104 104 104.0 0.600 0.530 EVO Head Quarters HQ-24 Y 20 36 52 19 236 251 39 98 107 102.3 0.500 0.500 EVO Head Quarters HQ-25 – 18 38 42 14 236 236 32 100 104 102.0 0.550 0.550 EVO Head Quarters HQ-26 – 20 54 53 22 254 255 42 107 106 106.3 0.600 0.530 89 EVO Head Quarters HQ-27 – 26 60 70 24 266 274 50 107 113 110.0 0.650 0.575

Incoming search terms:

Toyota Avensis Equipment REMOVAL AND INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 05-10-2011

Trip computer with fuel consumption &average speed display (where standard audio fitted) Outside temperature display Instrument display dimmer Digital odometer with two trip meters Digital Clock Dashboard integrated multi-information display (where standard audio fitted) Fuel Caplocation indicator Rearfoglamps indicator Sequential automatic transmission mode indicator (where sequential automatic fitted) Tachometer Fuel indicator with low fuel warning Water temperature indicator Engine temperature warning Engine management warning Lights Onwarning Door Ajarwarning



Incoming search terms: