insta trike installation manual

You search Auto repair manual PDF insta trike installation manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  insta trike installation manual Direct Download speed 5282 Kb/s

  insta trike installation manual Full Version speed 6162 Kb/s



HARLEY DAVIDSON BLADE FRONT WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. or FXSTD: Discard tapered spacer. NOTE Install short valve stem (43157-83A) included in the installation kit. Discard all other valve stems. 2. See Figure 2. Install valve stem assembly (L) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The side with the machined groove on the hub face is the primary bearing side for all kits except Kits 41681-07 and 40818-08. For Kit 41681-07: Install the wheel so that the hub markings are on the left side and the machined groove is on the right side of the motorcycle. • For 2006 and later FXDWG Models: When correctly installed, the tire will be 0.08-0.2 in (2-5 mm) off of center, compared to the fender. • For 2007 and later FX Softail and 2008 and later FXDWG Models: The left side of the wheel is the primary bearing side. • For 2006 and earlier FX Softail and 2007 and earlier FXDWG Models: The right side of the wheel is the primary bearing side. For Kit 40818-08: • Proper installation of this kit requires the separate purchase of two floating brake discs (44343-01 for 2004 – 2007 models and 44553-06A (stock) or 41500012 (polished) for 2008 and later models) and a tire (43371-07 on 2004-2008 models and 44026-09A on 2009-later models). The left side of the wheel has machined DOT markings to identify it as the primary bearing side. • For 2008 and later Touring: Install bearing shim (43903- 08) under the primary bearing. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. 4. For FLSTC and FLSTN Models: Install wheel kit and right hand wheel spacer provided in installation kit. Refer to FRONT WHEEL in service manual. For FXSTD Models: Install wheel kit, stock wheel spacer and right side wheel spacer provided in installation kit in place of the tapered spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install wheel kit, stock wheel spacers and spacer provided in installation kit between the left side wheel spacer and the left fork. For all other models: Install previously removed wheel spacers. Refer to FRONT WHEEL in service manual. 5. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to verify that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON 80-SPOKE REAR WHEEL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
Additional Parts Required This kit includes the custom wheel only. Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer: •Wheel Bearing Remover and Installer (HD-44060) •Wheel Installation Kit (See Service Parts Tables for part number) The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See the Service Parts section for kit contents. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. NOTE Remove the rear brake caliper before removing the wheel. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. Install the tube and tire on wheel. Refer to REAR WHEEL in the Service manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. 4. Install rear wheel (1), stock axle and stock axle nut. Refer to REAR WHEEL in Service Manual

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

HARLEY DAVIDSON BOOM! AUDIO MUSIC AND INTERCOM KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Intercom system flash (H-D Part No. 76441-06DT) Non-Ultra Overlay Harness (H-D Part No. 70169-06) NOTE For a more integrated appearance of the rider headset connector, the console may be replaced using an Ultra Classic Electra Glide console and/or console pod. See FLHTCU parts manual for applicable parts, and service manual for installation instructions. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 7 and Table 2. REMOVAL 1. Refer to the service manual and remove the following: a. Main fuse. b. Outer fairing. c. Seat. d. Fuel tank and console. e. Inner fairing cap. f. Wire trough cover. g. Left hand control. h. Left side saddlebag. INSTALLATION Install Switch Housing on Passenger Headset Harness 1. See Figure 1. Install push-to-talk switch housing (2) to passenger headset plug housing (3), included as part of passenger headset wire harness (see Figure 7, Item 6). 2. Position the switch housing so the knob is located close to the flip cap on the passenger headset connector. 3. Install self-tapping screws (1) to the switch housing but do not fully tighten at this time. Location adjustment may be required based on the motorcycle model, seats and accessories installed on the vehicle Secure Headset Connector and Switch Housing 1. 2006-2008 FLHX, FLTR, FLHT/C models: For motorcycles WITHOUT docking hardware, See Figure 7. Use the fender support cover fastener to install the smaller P-clamp (11) from the kit. For vehicles WITH docking hardware, use the front docking point fastener. Install the smaller P-clamp (11) between the outside face of the docking point behind the screw and washer. 2009-later FLHX, FLTR, FLHT/C models: For motorcycles WITHOUT docking hardware, see Figure 2. Use the threaded hole in the frame using screw (4), washer (3), spacer (2) and the smaller P-clamp (5) from the kit. For motorcycles WITH docking hardware, use the docking point shown in Figure 3. Install the smaller P-clamp from the kit to the outer end of the docking point using the docking point washer and screw. 2009-later Trike models without the Tour-Pak (FLHXXX): See Figure 4. The headset/switch assembly (1) will be secured to the frame at the location shown using the 1/2- 13 screw (3) and the larger P-clamp (2) from the kit. 2. For ALL models: Once the position of the PTT/VOL switch has been established, securely tighten the self-tapping screws installed to the switch housing earlier.

Incoming search terms:

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

HARLEY DAVIDSON FRONT DETONATOR WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Discard moon-style hub cap on FLSTC and FLSTN models. Discard left side spacer on FXSTS models and tapered spacer on FXSTD models. Refer to FRONT WHEEL in Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in Service Manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTE Install primary bearing first using the applicable Service Manual and WHEEL BEARING REMOVER/INSTALLER. Kit 44550-07: The left side of the wheel has a groove machined in the hub to identify it as the disc side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kits 44660-07 and 44661-07: The wheel should be installed so that the hub markings are on the left side of the motorcycle. An arrow engraved into the rim of 44661-07 indicates the direction of rotation. A groove is machined in the left-side hub face to indicate the primary bearing side. • Dual-disc models: Install the brake discs according to the Service Manual procedures. The Chrome hub cap (2) is not used. • Single-disc models: Install the brake disc according to the Service Manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Kit 44660-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 21-inch wheels. Kit 44661-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 19-inch wheels. Kit 44552-08: The left side of the wheel has a groove machined in the hub to identify it as the left side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kit 44556-07: The right side of the wheel has a groove machined in the hub to identify it as the right side for installa

HARLEY DAVIDSON FRONT NINE-SPOKE WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN models: Discard moon-style hub cap. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in service manual. NOTES Install the primary bearing first with the WHEEL BEARING REMOVER/INSTALLER, following the service manual instructions. The machined grooves in the hub face indicate the primary bearing side. The front wheel should be installed so that the valve stem is on the right side of the motorcycle. 4. Install wheel assembly parts from the appropriate service parts table for your fitment and stock brake disc(s). Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in service manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in kit installation. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual. 7. For 2009-Later TLE/U Sidecars: Assemble the sidecar brake disc and hub cap (purchased separately) to the wheel. The brake disc is to be installed on the side of the wheel opposite the valve stem. Install wheel according to the sidecar service manual

Honda VTX 1300 Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 27-10-2010

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) · Passenger Seat (to be reinstalled without modification) NOTE: OEM front and rear seat mounting bolts and brackets to be retained and reused. · Left and right passenger foot rests. (to be re-installed later). · Mufflers (to be re-installed and relocated with minor modification) · Rear Fender (complete w/ sub frame and all attaching parts) · Swing Arm, Drive Shaft and Rear Wheel (complete w/ all attaching parts) · Rear brake Line to hard line in front of the Swing Arm. Core Return There are NO core return parts for this model. Honda VTX 1300 TRIKE CONVERSION CHAMPION TRIKES Installation Manual Page 7 of 16 Revision 2 3 Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Cut and remove passenger foot rest mount from OEM frame on both sides (left hand side picture shown) . Figure 1 b. Clean cut frame and paint black. c. Remove and secure Charcoal Canister. d. Cut and remove charcoal canister frame bracket. Figure 2 e. Clean cut frame and paint black

Incoming search terms:

HARLEY DAVIDSON SOFTAIL 6 SPEED TRANSMISSION – COMPLETE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 3. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. 4. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. 6. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter. 7. See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. 8. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. 9. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing. 10. Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. 11. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. 12. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. 13. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation

Incoming search terms:

Incoming search terms: