installing an airfilter kn a 2003 honda rubicon 500

You search Auto repair manual PDF installing an airfilter kn a 2003 honda rubicon 500, if there are search results will appear below. If search results do not exist, please search by others keyword.



  installing an airfilter kn a 2003 honda rubicon 500 Direct Download speed 5282 Kb/s

  installing an airfilter kn a 2003 honda rubicon 500 Full Version speed 6162 Kb/s



Honda Foreman 500 And Honda Rubicon WINCH MOUNTING KIT INSTALLATION

0

Filed Under (Honda) by admin on 13-12-2011

download
Begin by removing the front skid plate located on the front of the ATV. Remove the four side 8mm bolts and four bottom 6mm bolts securing the front skid plate, figure 1. Save the fasteners as they will be used later to reinstall the front skid plate. 2. Remove the four plastic rivets on each side of the front plastic fascia, figure 2. Use a large screw driver to carefully remove the center rivet. After removing the center rivet, remove the rivet housing. Save the fasteners as they will be used to reinstall the front plastic fascia. 3. Remove the two 6mm bolts that attach the front plastic fascia to the bumper, figure 3. Remove the front plastic fascia at this time . Remove the two 6mm bolts that attach the front bumper to the plastic headlight assembly, figure 4. Save the fasteners as they will be used to reinstall the front bumper. 5. Remove the two top 8mm bumper bolts that attach the front bumper to the front rack, figure 5. Save the fasteners as they will be used to reinstall the front bumper. Figure 5 Remove Top Bumper Bolts Remove (both sides) 6. Remove the two ottom bumper bolts that attach the bumper to the bottom of the vehicle frame, figure 6. Save the fasteners as they will be used to reinstall the front bumper

Incoming search terms:

2002-2003 Honda GL1800/ A Frame Weld REPAIR PROCEDURE OVERVIEW

0

Filed Under (Honda) by admin on 14-12-2010

download
If your inspection identifies a crack or cracks in or on either Left or Right lower crossmember frame welds, STOP – call your DSM or TechLine for further instructions. • If your inspection reveals no cracks, proceed to REPAIR PROCEDURE. NOTE: Verification of repair can also be found in the Dealer Responsibility Report and on the Honda Interactive Network (iN). If you have any questions about verification, please contact TechLine before proceeding. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510) • Frame Weld Inspection Chart (S0513) You MUST provide your TIG welder with the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • Welding Template Box (S0512) All of the above items were shipped to you with this Service Bulletin. If you need additional copies of the Dealer Booklet , Welding Manual , Welding Template Box , or Frame Weld Inspection Chart , you may order them at no cost from DDS at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. Disassembly Overview You will be removing the following components from the vehicle as instructed in the Dealer Booklet : • Handlebar weights • Rear view mirrors • Swingarm pivot covers • Rider foot pegs • Seat • Side covers/Engine side covers • Fairing pockets • Fairing molding • Meter panel • Top shelter • Battery • Fuel tank • Main wiring harness ground • Front lower fairing • Front exhaust pipe protector • Muffler/exhaust pipe • Antenna Whip(s) • Coolant reserve tank • Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: You MUST cover the following with RED duct tape for welder identification pur- poses: • Negative (-) and positive (+) battery cables • Fuel return hose end • Fuel feed hose end • Main wiring harness ground • Alternator • Exhaust ports Welding Overview A qualified TIG welder will weld the frame following the procedures in the 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual . Re-assembly Overview You will be inspecting the new TIG welds, painting the frame, and re-assembling the vehicle as detailed in the Dealer Booklet and Frame Weld Inspection Chart (S0513)

Incoming search terms:

HARLEY DAVIDSON V-Series California Engine Owner's Manual

0

Filed Under (Harley Davidson) by admin on 28-11-2010

download
During Break-In At 50 Miles (80 Kilometers): 1- Change engine oil and filter. 2- Inspect for fuel and oil leaks. 3- Inspect air cleaner element and service as required. 4- Check tightness of exterior fasteners, except head bolts. Engine Maintenance at 500 Miles (800 Kilometers): 1- Change engine oil and filter. 2- Inspect for fuel and oil leaks. 3- Inspect air cleaner element and service as required. 4- Check tightness of exterior fasteners, except head bolts. 5- Check operation of enrichment device and throttle controls. 6- Check engine idle speed. 7- Check tightness of engine mounts. Regular Service Intervals Regular lubrication and maintenance will help keep your new S&S engine operating at peak performance. The following table presents the required service schedule for normal operating conditions. Failure to complete the required engine maintenance can result in engine damage and an increase in emissions. Please refer to the motorcycle owner’s manual for any additional required chassis maintenance. Engine Service Intervals Item Interval Engine Oil & Filter Change at 50, 500, 2,500 miles (80, 800, 4,000 kilometers), every 2,500 miles (4,000 kilometers) thereafter1 Air Cleaner Element Inspect at 50 and 500 miles (80 and 800 kilometers), every 2,500 miles (4,000 kilometers) thereafter2 Tappet Oil Screen Inspect every 2,500 miles (4,000 kilometers). Replace every 5,000 miles (8,000 kilometers). Petcock, Lines, & Fittings, Vacuum Lines Inspect at 50 and 500 miles (80 and 800 kilometers), every 2,500 miles (4,000 kilometers) thereafter. Fuel Tank Filter Screen & In-Line Fuel Filter (If used) Inspect every 5,000 miles (8,000 kilometers). Engine Idle Speed Adjust as required. Operation of Throttle & Enrichment Device ControlsInspect at 500 miles (800 kilometers) and every 2,500 miles (4,000 kilometers) thereafter. Spark Plugs Inspect every 5,000 miles (8,000 kilometers). Replace every 10,000 miles (16,000 kilometers) or as needed. Ignition Timing Inspect every 5,000 miles (8,000 kilometers). Engine Mounts Inspect at 500 miles (800 kilometers) and every 5,000 miles (8,000 kilometers) thereafter. External Fasteners Except Engine Head Bolts Re-torque at 500 miles (800 kilometers) and every 5,000 miles (8,000 kilometers) thereafter. 1- S&S recommends that petroleum-based oil not specifically formulated for motorcycles should be changed every 1,000 miles (1,600 kilometers) after the break-in period. 2- Replace more frequently if required or if engine is operated in a dusty environment.

Incoming search terms:

2003-2004 HONDA GL 1800/A Frame Weld Safety Recall

0

Filed Under (Honda) by admin on 15-12-2010

download
there is no punch mark on the VIN plate as specified in this Service Bulletin, proceed to the REPAIR PROCEDURE section of this Service Bulletin. IMPORTANT: Due to the complexity of this campaign it is imperative that you check iN and your Dealer Responsibility Report before you begin repairs. If iN or your Dealer Responsibility Report indicate the Safety Recall has been performed, but you confirm the unit is not punched and the repair has actually been done (by inspecting the weld), please contact the Warranty HelpLine at (800) 421-1900, option 7. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510)  Frame Weld Inspection Chart (S0516) You MUST provide your TIG welder with the following items:  2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511)  2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) Welding Template Box (S0512) All of the above items were shipped to you with Service Bulletin GL1800 #14. If you need additional copies of these materials, you may order them from Resolve at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. DISASSEMBLY OVERVIEW You will be removing the following components from the vehicle as instructed in the Dealer Booklet : Handlebar weights Rear view mirrors Swingarm pivot covers Rider foot pegs Seat Side covers/Engine side covers Fairing pockets Fairing molding Meter panel Top shelter Battery Fuel tank Main wiring harness ground Front lower fairing Front exhaust pipe protector Muffler/exhaust pipe Antenna Whip(s) Coolant reserve tank Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: Before you send the motorcycle to the welder, you MUST check for lower crossmember frame weld cracks.  If your inspection reveals no cracks in or on either the Left or Right lower cross- member frame welds, proceed to the REPAIR PROCEDURE OVERVIEW section of this Service Bulletin.  If your inspection identifies a crack or cracks in or on either the Left or Right lower crossmember frame welds, perform the following procedure: Place the grinding template (S0512) on the crossmember. Using a suitable felt marker, draw a line on the weld with the crack, drawing the line along the entire edge of the the template (this line will be 89 mm long). If the crack falls within the length of this line (89 mm) , prepare the motorcycle for welding per the Dealer Procedures and advise the welder to use the Cracked Weld Repair Manual (S0515). After the bike has returned from the welder, prepare the frame and re-assemble the motorcycle per the Dealer Procedures . Then, proceed

Express ATVS -250cc Cobra Setup/ Installation Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
Unpacking your Cobra Installing the front shock Installing the front tires Installing rear shocks Installing the rear tires Installing seats and harnesses Steering wheel installation Roll cage installation Safety checks / Adjustments General maintenance Unpacking your Cobra First off you should pull the carton off from your new 250 Cobra cart. Inspect the cart thoroughly to make sure that your new Cobra has not been heavily damaged. You will notice that the product has a metal frame holding it in place; you may want to start removing bolts from the shipping steel frame. The next step is to remove the metal frame and lift it off of the cart. Remove any of the metal frame that may afford resistance when working on the cart it self. Be careful the metal frame may be heavy and sharp. Now would also be a good time to inspect your Cobra a little more thoroughly. In the box with the Cobra you should have found a box containing miscellaneous hardware. Installing the front shock Using some of the bolts you found in your box, install the front shocks sliding the bolt through the brackets and tighten the nut down. Next, you will need to place the ball head into the turning arm, then tighten the castle nut and insert a cotter pin so that the castle nut doesn’t loosen and become a hazard. Installing the front tires
Find the front tires and place them on the front hub and place the lug nuts on the studs. Tighten them down. Make sure that all of the lug nuts are on tightly. Installing the rear shocks Moving to the rear of the Cobra you will notice the rear shocks are not inserted. Place the rear shocks into the bracket on the rear of the Cobra. Slide one of the provided bolts through the bracket and shock eyelet and tighten the bolt down. Installing the rear tires Now that the shocks have been placed properly you can install the rear tires, place the tires onto the axle then place the rear rim lined up onto the axle and tighten the provided castle nut down. Place the cotter pin through the axle and bend off to the side. This is so the castle nut does not loosen under load. Installing the seats and harnesses
(The arrow points to an example of where the seat bolts mount) Find the two racing seats shipped in the box with the Cobra. You will need to affix them to the frame by sliding the bolts up through the bottom of the frame. This can be tricky so have patience. Once both seats have been placed in the cart and tightened find the harnesses. Once found the harnesses mount to a bracket behind the seats. Place a bolt through the bracket and bolt the harnesses down tightly. Installing the steering wheel Find the steering wheel and place it onto the steering wheel mount. Grab the six small screws and place them through the steering wheel and mount, tighten them down but also make sure the top of the wheel is facing up. Installing the roll cage

Incoming search terms:

2003 Honda ST1300lA OWNER'S MANUAL

0

Filed Under (Honda) by admin on 24-04-2011

download
Gauges & Indicators Lights when engine oil pressure is low enough to cause engine damage. If the indicator lights, pull safely to the side of the road. See page 162 for instructions and cautions. Lamp Check. PGM-FI malfunction indicator lamp (red) low oil pressure indicator (red) Lights when there is any abnormality in the PGM-FI (Programmed Fuel Injection) system. Should also light for a few seconds and then go off when the ignition switch is turned ON and the engine stop switch is at RUN. If the indicator comes on at any other time, reduce speed and take your motorcycle to a Honda dealer as soon as possible. Lamp Check. anti-lock brake system (ABS) indicator (red) ABS (ST 1300A) Lights when there is any abnormality in the anti-lock brake system (ABS). Normally, this indicator comes on when the ignition switch is turned ON, and goes off after you ride the motorcycle at a speed above 6 mph (10 km/h)If the indicator comes on while riding, stop the motorcycle in a safe place and turn off the engine. Refer to ABS indicator, page 61. For information about ABS, see page 60. LampCheck Use this button for the following purposes. To adjust time To adjust display illumination Use this button for the following purposes. To adjust time To select and reset the fuel mileage meter To change the mileage units for the odometer/tripmeter and available driving distance Use this button for the following purposes. To adjust time To select and reset the tripmeter

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

Honda GL 500 MiniTrike Installation Manual

0

Filed Under (Honda) by admin on 29-04-2011

download
Refer to diagram for bracket identification 1. Secure motorcycle in an upright stable position 2. Attach bracket A (left) to rear footpeg mount. 3. Attach bracket B (right) to rear footpeg mount. 4. Remove rear saddlebags. 5. Attach top of brackets C/D to saddlebag sub frame hardware as in photo. Place enclosed 3/8 spacer between brackets C/D and inside of sub frame. 6. Attach axles and wheels to MiniTrike frame and place in proper position and relation behind motorcycle. 7. Attach bracket A (left) / B (right) to TOP of forward attaching points on MiniTrike frame. 8. Attach bottom of brackets C/D to rear mounting plate on MiniTrike frame 9. Ensure MiniTrike is square with motorcycle and tighten all bolts. 10. Remount saddlebags. Wheel Alignment Wheel alignment is critical for proper tire wear and handling. With MiniTrike installed measure A and B . Loosen axle plates and align wheel so A and B are equal to within 1/16th of an inch. Tighten axle bolts and torque to 45 pounds. Repeat for C and D . It may be necessary to shim axle plates for proper alignment. NOTE : The measurement of A and B may not be the same as C and D. This is normal and presents no difficulty

Honda GL 500 Installation Manual

0

Filed Under (Honda) by admin on 21-11-2010

download
Wheel Alignment Wheel alignment is critical for proper tire wear and handling. With MiniTrike installed measure A and B . Loosen axle plates and align wheel so A and B are equal to within 1/16th of an inch. Tighten axle bolts and torque to 45 pounds. Repeat for C and D . It may be necessary to shim axle plates for proper alignment. NOTE : The measurement of A and B may not be the same as C and D. This is normal and presents no difficulty. Wheel Height / Traction Adjuster The wheel height/traction adjuster (right and left side) allows you to selectively adjust the position of your trike wheels in order to customize ride, handling, level, and traction characteristics. Your trike is shipped with the adjuster preset to an optimum position for your model of motorcycle however you can make whatever adjustments necessary to customize to your bike and personal preference. Shortening the adjuster arm raises the trike wheels and places more of the weight of your motorcycle on the motorcycle wheel. This increases motorcycle traction and gives a generally softer ride. 1) Loosen jam nuts 2) Shorten adjuster arm by turning adjuster nut A toward bolt C desired amount. 3) Turn adjuster nut B until it tightens against adjuster bracket and adjuster nut A 4) Tighten nuts A and B and jam nuts Lengthening the adjuster arm lowers the trike wheels and places more of the weight of your motorcycle on the trike wheels. This gives a firmer ride and increases handling/cornering. 1) Loosen jam nuts 2) Lengthen adjuster arm by turning adjuster nut B toward bolt D desired amount. 3) Turn adjuster nut A until it tightens against adjuster bracket and adjuster nut B 4) Tighten nuts A and B and jam nuts

2001 – 2003 Prius 2003 4Runner, Camry, Land Cruiser and Sequoia VEHICLES EQUIPPED WITH TRANSPONDER ECU

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. 2. Turn the ignition ON (engine OFF). 3. Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes. 4. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. 5. Register any additional keys as necessary. 6. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below.

Incoming search terms:

Incoming search terms: