installing docking hardware

You search Auto repair manual PDF installing docking hardware, if there are search results will appear below. If search results do not exist, please search by others keyword.



  installing docking hardware Direct Download speed 5282 Kb/s

  installing docking hardware Full Version speed 6162 Kb/s



HARLEY DAVIDSON DYNA DOCKING HARDWARE FOR FXDX WITH WIDE TIRE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
Installation NOTE Perform the following procedures on one side of the motorcycle until instructed to go to the other side. To keep fender in alignment the front docking point will be mounted first. INSTALLING DOCKING POINTS NOTE Save the acorn nuts and washers removed from the fender support bracket for use when installating docking points. 1. Loosen and remove the acorn nuts, washers, and screws from the fender support (right-hand) bracket. Save the washers and acorn nuts for docking point installation. Discard screws. 2. Obtain 1 plastic bushing, labeled 01, from a bushing set. 3. Place the bushing (4) (beveled side out) into the front support hole as shown in Service Parts illustration. 4. Place the countersunk side of the front docking point (2) so that it engages bushing (4). 5. From underneath (inside) the fender, insert hex-head screw (1) through fender, support bracket and front docking point (2). 6. Install washer (7) split lockwasher (5) and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 7. Obtain another plastic bushing, labeled 01 , from the bushing set. 8. Place bushing (4) (beveled side out) into the the rear support hole as shown in Service Parts illustration. 9. Place the countersunk side of the rear docking point (3) so that it engages bushing (4). 10. From underneath (inside) the fender, insert hex-head screw through fender, support bracket and rear docking point (3). 11. Install washer (7) split lockwasher (5)and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 12. Repeat procedures 1 through 11 for opposite (left-hand) side of the motorcycle. NOTE In time docking points may wear, causing the sideplates to become loose. The fit may be tightened using the following procedure. 1. Loosen docking hardware. 2. Rotate docking points clockwise approximately 45°. 3. Tighten docking hardware to the appropriate torque values. Repeat as often as required, up to 3 times

Incoming search terms:

HARLEY DAVIDSON DYNA DOCKING HARDWARE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION Installing the Front Docking Point To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Remove the seat and disconnect the negative (-) battery cable. NOTE To keep the fender aligned, complete ALL the following procedures on one side of the motorcycle before starting the other side. 2. See Figure 1. Remove the stock fender support bracket. Position new rear fender mounting bracket from kit (5) into position. 3. Apply Loctite 243 (Blue) to button head bolt (2) prior to installation. Place the tapered side of front docking point (1) against the strut cover. Insert button head bolt (2) through the docking point, fender support and fender. Tighten to 12-18 ft-lbs (16.3-24.4 Nm) . 4. If used without saddlebags, install rear docking point (3) and recess cover (4) according to instructions in Part Number 53968-06C, Directional Relocation Kit. If used with saddlebags, mount rear docking point according to instructions with saddlebag kit. MAINTENANCE NOTE In time, the docking points may wear causing the mating luggage rack or sideplates to become loose. The fit may be tightened using the following procedure. If any fasteners with Loctite are loosened, then the fasteners must be removed, cleaned of existing Loctite and re-installed with new Loctite. 1. Loosen the docking hardware. 2. Rotate the docking points clockwise approximately 45°. 3. Tighten the docking hardware to the appropriate torque values as indicated in the installation procedures. This procedure can be repeated up to 3 times before replacement of the docking points is recommended.

Incoming search terms:

HARLEY DAVIDSON FLSTC & FLSTS DOCKING HARDWARE WITH SADDLEBAG SUP- PORTS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
The rear docking points in kit part number 90366-03 provide the rear mounting points for the Solo Rack. The rear mounting points from this kit ( 53931-03A ) will need to be installed to provide the clearance for the Solo Rack to be mounted. Table 2. Turn Signal Relocation Kit Requirement Turn Signal Relocation Kit Required Accessory Part Number 2003 and later FLSTC Not required 53815-00 Detachable Sideplates Not required 53066-00A Detachable Tour Pak Rack REMOVAL FLSTS Saddlebag Assembly Removal 1. See Figure 15. Remove a saddlebag by removing the acorn nut and washer on the lower support and the two flange locknuts inside the bag. Discard the flange locknuts but retain the acorn nut and washer. 2. See Figure 1. Remove the saddlebag support studs and their mounting hardware. 3. Repeat steps 1 – 2 on the other side of the vehicle. FLSTC Saddlebag and Fixed Mount Sissybar Removal 1. See Figure 15. Remove a saddlebag by removing the acorn nut and washer on the lower support and the two flange locknuts inside the bag. Discard the flange locknuts, but retain the acorn nut and washer. 2. See Figure 1. Remove the saddlebag support studs and their mounting hardware. 3. Remove and discard fixed mount sideplates. Retain sissy bar for use with detachable sideplates. 4. Repeat steps 1 – 3 on the other side of the vehicle. 1 is06914 1. Saddlebag support studs Figure 1. Original Equipment Hardware (FLSTS model shown) INSTALLATION Docking Hardware Installation – For Detachable Sideplates or Tour-Pak Rack NOTE See Figure 15. The rear docking point (8) is wider than the front docking point (2). -J02425 1 of 5 1. Place front docking point (2) on front stud (1), with countersunk end of docking point facing fender support. 2. Place spacer (6) for side plates or mid docking point (for detachable sideplate kit) on rear stud (1). 3. Place rear docking point (8) on bolt (7), with countersunk end facing fender support. 4. Insert front stud (1) through front docking point (2), fender support and into bracket underneath fender as shown. 5. Insert rear stud (1) through fender support and into bracket underneath fender as shown. 6. Install bolt (7) through fender support and into bracket underneath fender as shown. 7. Tighten front and rear studs (1) and bolt (7) to 27 ft-lbs (37 Nm) . 8. Repeat steps 1-7 on the other side of the vehicle.

Incoming search terms:

HARLEY DAVIDSON XL DOCKING HARDWARE/ DIRECTIONAL RELOCATION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION 1. See Figure 2. Following directions supplied with saddlebags to relocate rear turn signals, but also use the following exceptions to install the parts contained in this kit: •Use turn signal studs (4) in place of hex bolts supplied with saddlebags. The longer studs are required to accommodate the rear docking points. •On each side, insert relocation pad plate (3), saddlebag mount spacer (12), rear docking point (2), and docking point spacer (11) between relocation pad (supplied with saddlebags), and fender support cover as shown. •Use 4-inch long cap screw (5) in place of hex bolts supplied with saddlebags. The longer cap screws are required to accommodate the rear docking points. •The turn signal wires should be routed under the fender support cover back to the connectors they were removed from following the directions supplied with saddlebags. 7 1 14 2 12 6 9 3 1 11 4 10 8 16 17 15 18 5 13 is03490a 1. Locknut, 5/16-18 inch (3) 2. Rear docking point 3. Relocation pad plate from saddlebag kit 4. Turn signal stud 5. Cap screw, 5/16-18 x 4 inch 6. Spacer from saddlebag kit 7. Turn signal wire 8. Fender support cover 9. Cap screw, 5/16-18 x 2-1/4 inch 10. Front docking point 11. Docking point spacer 12. Saddlebag spacer 13. Washer, 1/4 inch 14. Locknut 1/4-20 inch 15. Cap screw, 1/2-13 x 3-3/4 inch 16. Spacer 17. Saddlebag support 18. Stock washer Figure 1. Installation shown on 2000 model On 1999 and earlier models: See Figure 2. Before mounting saddlebag supports, remove acorn nut from upper shock mount, and install washer (7), and shock mount spacer (8) as shown. Tighten upper shock mount spacer to 21-35 ft-lbs (28-47 Nm). This will properly space out the saddlebags to accommodate the docking points. On 2000 models: See Figure 1. Before mounting saddlebag supports remove button screw from upper stock mounts, and proceed to Step 2.

Incoming search terms:

HARLEY DAVIDSON FOUR-POINT DETACHABLE DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. See Figure 3. Remove the screw (A) retaining the rear of the chrome cover to the rear frame extension on each side of the vehicle. 2. Place a washer (7) over the threads of each of the larger TORX® head screws (6) from the kit. Apply 2 or 3 drops of Loctite 262 Threadlocker and Sealant – Red to the threads of each screw. Install the screws through the docking plates (1) and fender covers, and into the threaded holes in the frame extensions on each side of the vehicle, and tighten to 17 ft-lbs (23 Nm) . NOTE See Figure 1. The docking points must be attached to the docking plates (2) with the chamfer (1) facing the plate and the flat side facing out. 1 2 is05506a 1. Docking point chamfer (bevel) 2. Mounting plate Figure 1. Docking Point Installation 3. See Figure 3. Slide a spacer (2) onto the longer pin (B) of each docking plate. Install the four docking points (3), chamfer end first, onto the long and short docking plate pins using the washers (5) and smaller TORX screws (4). Tighten to 10.5 ft-lbs (14.2 Nm) . NOTE Protective tape must be installed to the rear saddlebag mounting bracket to prevent damage to the saddlebag finish when the lid is opened. 4. See Figure 2. Apply protective tape (2) to the rear mounting bracket (1) on the saddlebag in the location shown. Repeat for the other side. 2 1 is05533 1. Rear saddlebag bracket (2) 2. Protective tape %lengthT=0

Incoming search terms:

HARLEY DAVIDSON FXSTD DETACHABLE WINDSHIELD AND DOCKING HARDWARE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
INSTALLATION NOTE Use the Docking Hardware Kit to assemble two upper and two lower clamps. See the Service Parts illustration. The upper clamps use a mounting pin (4) and the lower clamps use a button head screw (5) to fasten the windshield mounting bushing. 1. Assemble the windshield docking hardware as follows: a. Install a larger chrome washer (6) and bushing (7) onto a button head screw (5). Thread the screw into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. b. Install a larger chrome washer (6) and bushing (7) onto a mounting pin (4). Thread the pin into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. 2 1 3 4 4 5 is 02187 1. Upper clamp 2. Lower clamp 3. Fork tubes 4.1/8 inch (3 mm) approximately 5.3.0 inch (76 mm) Figure 1. Installing Clamps NOTE Place shop rags on the headlamp, front fender and front of the fuel tank to prevent scratches to these components. Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts. 2. See Figure 1. Install a lower clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the top of the lower triple clamp, then finger tighten the lock nut. Repeat with the second lower clamp and fork tube. NOTE Keep front wheel straight to prevent brackets from scratching fuel tanks. See Figure 1. Install the clamps on the fork tubes so the bushing center lines are 3 inches (76 mm) apart. 3. Install an upper clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the bottom of the upper triple clamp. Ensure that the center lines of the upper and lower bushings are 3 inches (76 mm) apart, then finger tighten the lock nut. Repeat with the second upper clamp and fork tube

HARLEY DAVIDSON XL DETACHABLE SOLO RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-04-2011

download
Kit Contents See Figure 2 and Table 1. There are no Service Parts available with this kit. INSTALLATION 1. See Figure 2. While standing behind the motorcycle, place the front rack notches (1) into the front docking points (2). NOTE Check alignment as shown in Figure 1. Failure to properly align the docking points and sideplates may result in damage to the rear docking points. 2. Pull the rotary latches (3) back into their rearmost position. Position the rear rotary latches over the rear docking points (6), ensuring the latches and sideplates (4) fit into the neck (5) of the rear docking points. This may require some gentle squeezing or spreading of the sideplates. NOTE The front and rear docking points must be fully engaged. If docking points are not fully engaged or docking kit is loose, it could shift position or come loose during operation. 3. Push down and close the rotary latches by pressing the latch lever (7) as far forward as it will go. You will hear a click when the latch is in place. If the latch does not easily close, do not force. Recheck alignment as described in Step 2. 4 4 3 2 2 1 1 1 2 is 00963 1. Right sideplate 2. Right front docking point 3. Correct: sideplate fully engaged in docking point 4. Incorrect: sideplate NOT fully engaged in docking point Figure 1. Sideplate Must Fit into Docking Point Correctly REMOVAL 1. See Figure 2. To remove the rack, press the release button (8), and pull the rotary latch lever back. Carefully lift the rear of the rack up and pull the rack out of the front docking points

HARLEY DAVIDSON BOOM! AUDIO MUSIC AND INTERCOM KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Intercom system flash (H-D Part No. 76441-06DT) Non-Ultra Overlay Harness (H-D Part No. 70169-06) NOTE For a more integrated appearance of the rider headset connector, the console may be replaced using an Ultra Classic Electra Glide console and/or console pod. See FLHTCU parts manual for applicable parts, and service manual for installation instructions. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 7 and Table 2. REMOVAL 1. Refer to the service manual and remove the following: a. Main fuse. b. Outer fairing. c. Seat. d. Fuel tank and console. e. Inner fairing cap. f. Wire trough cover. g. Left hand control. h. Left side saddlebag. INSTALLATION Install Switch Housing on Passenger Headset Harness 1. See Figure 1. Install push-to-talk switch housing (2) to passenger headset plug housing (3), included as part of passenger headset wire harness (see Figure 7, Item 6). 2. Position the switch housing so the knob is located close to the flip cap on the passenger headset connector. 3. Install self-tapping screws (1) to the switch housing but do not fully tighten at this time. Location adjustment may be required based on the motorcycle model, seats and accessories installed on the vehicle Secure Headset Connector and Switch Housing 1. 2006-2008 FLHX, FLTR, FLHT/C models: For motorcycles WITHOUT docking hardware, See Figure 7. Use the fender support cover fastener to install the smaller P-clamp (11) from the kit. For vehicles WITH docking hardware, use the front docking point fastener. Install the smaller P-clamp (11) between the outside face of the docking point behind the screw and washer. 2009-later FLHX, FLTR, FLHT/C models: For motorcycles WITHOUT docking hardware, see Figure 2. Use the threaded hole in the frame using screw (4), washer (3), spacer (2) and the smaller P-clamp (5) from the kit. For motorcycles WITH docking hardware, use the docking point shown in Figure 3. Install the smaller P-clamp from the kit to the outer end of the docking point using the docking point washer and screw. 2009-later Trike models without the Tour-Pak (FLHXXX): See Figure 4. The headset/switch assembly (1) will be secured to the frame at the location shown using the 1/2- 13 screw (3) and the larger P-clamp (2) from the kit. 2. For ALL models: Once the position of the PTT/VOL switch has been established, securely tighten the self-tapping screws installed to the switch housing earlier.

Incoming search terms:

Express ATVS -250cc Cobra Setup/ Installation Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
Unpacking your Cobra Installing the front shock Installing the front tires Installing rear shocks Installing the rear tires Installing seats and harnesses Steering wheel installation Roll cage installation Safety checks / Adjustments General maintenance Unpacking your Cobra First off you should pull the carton off from your new 250 Cobra cart. Inspect the cart thoroughly to make sure that your new Cobra has not been heavily damaged. You will notice that the product has a metal frame holding it in place; you may want to start removing bolts from the shipping steel frame. The next step is to remove the metal frame and lift it off of the cart. Remove any of the metal frame that may afford resistance when working on the cart it self. Be careful the metal frame may be heavy and sharp. Now would also be a good time to inspect your Cobra a little more thoroughly. In the box with the Cobra you should have found a box containing miscellaneous hardware. Installing the front shock Using some of the bolts you found in your box, install the front shocks sliding the bolt through the brackets and tighten the nut down. Next, you will need to place the ball head into the turning arm, then tighten the castle nut and insert a cotter pin so that the castle nut doesn’t loosen and become a hazard. Installing the front tires
Find the front tires and place them on the front hub and place the lug nuts on the studs. Tighten them down. Make sure that all of the lug nuts are on tightly. Installing the rear shocks Moving to the rear of the Cobra you will notice the rear shocks are not inserted. Place the rear shocks into the bracket on the rear of the Cobra. Slide one of the provided bolts through the bracket and shock eyelet and tighten the bolt down. Installing the rear tires Now that the shocks have been placed properly you can install the rear tires, place the tires onto the axle then place the rear rim lined up onto the axle and tighten the provided castle nut down. Place the cotter pin through the axle and bend off to the side. This is so the castle nut does not loosen under load. Installing the seats and harnesses
(The arrow points to an example of where the seat bolts mount) Find the two racing seats shipped in the box with the Cobra. You will need to affix them to the frame by sliding the bolts up through the bottom of the frame. This can be tricky so have patience. Once both seats have been placed in the cart and tightened find the harnesses. Once found the harnesses mount to a bracket behind the seats. Place a bolt through the bracket and bolt the harnesses down tightly. Installing the steering wheel Find the steering wheel and place it onto the steering wheel mount. Grab the six small screws and place them through the steering wheel and mount, tighten them down but also make sure the top of the wheel is facing up. Installing the roll cage

Incoming search terms:

HARLEY DAVIDSON XL DETACHABLE UPRIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
INSTALLATION Install Docking Point Kit Install the docking point kit following the instructions in that kit. Passenger Upright Installation 1. See Figure 1. Stand behind the motorcycle, and place (10) the front upright notches (2) into the front docking points (3). 2. See Figure 2. Check for correct notch engagement. NOTE Failure to correctly engage the sideplate notches to the docking points may result in damage to the rear docking points. 3. See Figure 1. Push (11) the rotary latches (4) into their most forward position. Align the latches over the rear docking points (7), making sure the latches and rear notches (6) fit into the neck (8) of the rear docking points. NOTE This may require some gentle squeezing or spreading of the upright sideplates. 4. Push downward (12) on the sideplates, and close the rotary latches by pulling (13) the latch levers as far back as they will go. A click will be heard when the latch is in place. If the latch does not close, do not force it. 2 12 3 7 4 1 5 9 10 5 7 8 6 4 13 11 is06182a 1. Upright 2. Front notch 3. Front docking point 4. Rotary latch 5. Release button 6. Rear notch 7. Rear docking point 8. Rear docking point neck 9. Fender support bracket 10. Place front notches into front docking points 11. Push latches forward 12. Lower rear notches onto rear docking points 13. Pull rearward to close latches Figure 1. Detachable Upright

Incoming search terms: