instructions for 62970 02 lcd dip stick

You search Auto repair manual PDF instructions for 62970 02 lcd dip stick, if there are search results will appear below. If search results do not exist, please search by others keyword.



  instructions for 62970 02 lcd dip stick Direct Download speed 5282 Kb/s

  instructions for 62970 02 lcd dip stick Full Version speed 6162 Kb/s



HARLEY DAVIDSON LCD OIL TEMPERATURE/ LEVEL DIPSTICK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
LCD DIPSTICK INSTALLATION 1. Remove the original equipment (OE) dipstick from the filler neck. 2. Non-threaded Dipsticks: Lightly oil the O-ring on the new LCD dipstick. Orient the dipstick so that the display window is horizontal and readable from left to right, with the Bar and Shield logo to the left (towards the rear of the motorcycle). Push the dipstick straight into the filler neck until it seats. 3. For threaded dipsticks: Lightly oil O-ring and screw into the transmission like OE dipstick. If the orientation of the display is unsatisfactory when fully seated, refer to Adjusting the Display Angle later in these instructions. NOTE To be sure of correct readings, the dipstick MUST seat firmly against the flange. LCD DIPSTICK USE AND CARE Removing the Dipstick The dipstick assembly must be removed from the filler neck to add oil or to service the internal battery. Displaying the Oil Temperature and Level See Figure 1. Press and release the rubber button on the front face to display the temperature of the oil in the oil tank in degrees Fahrenheit (°F), and the oil level. The display will automatically shut off after approximately ten seconds. Do not overfill oil tank. Doing so can result in oil carryover to the air cleaner leading to equipment damage and/or equipment malfunction. (00190a) NOTES Oil level cannot be accurately measured: • on a cold engine • with the motorcycle upright • with the engine running NOTE Oil level on 2000 through 2004 Softail models with the original dipstick is checked with the motorcycle standing upright (not leaning on the jiffy stand). THIS IS NOT THE CASE with the LCD oil temperature/level dipstick. For all 2000 and later Softail models, oil level inspection must be done with the motorcycle LEANING ON the jiffy stand, on level ground. For pre-ride oil level inspection: With the motorcycle on level ground, RESTING ON the jiffy stand : •The oil level should be as indicated in Figure 1, display 4 through 8 (bars showing oil level, and “COLD OIL” message followed by flashing oil temperature) when the engine is cold. DO NOT ADD OIL to bring the level to the FULL mark on the dipstick of a COLD engine. •If the oil level indicates as in display 9 (animated level bars, followed by an “888 NO SENSOR” code), the wires inside the dipstick may be disconnected or damaged. Refer to Replacing the Battery later in these instructions to separate the dipstick upper and lower assemblies. If the small plug next to the battery has become dislodged from the receptacle, plug it in. If a visible wire is damaged, a repair can be attempted. If no damage is visible, the dipstick is damaged internally and should be replaced. For oil level inspection at operating temperature: Ride the motorcycle until the engine is at normal operating temperature. Idle for 1-2 minutes with the motorcycle on level ground, RESTING ON the jiffy stand (except Softails) , turn the engine OFF.

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

1998 BMW R1100RT LCD Temperature Gauge Scale Calibration LCD Fuel Gauge Calibration Fuel Sender Testing and Cleaning

0

Filed Under (BMW) by admin on 26-10-2010

download
Oil Temperature and Gauge 2.1. Introduction My 1998 BMW R1100RT came with an LCD temperature gauge that shows horizontal black bars in a vertical motif, to indicate temperature. This is difficult to interpret at speed (how many bars are exposed?) and does not actually tell me what the oil temperature is. 2.2. Normal Operation The bike seems to run at 5 or six bars under normal conditions. It appears that the oil thermostat for the cooler is set to ’5 bars’. 2.3. Over Heating The LCD panel indicates that 8 bars is the maximum normal operating temperature. It would be useful to know what the actual temperature is. Modern oils have a normal operating temperature of approximately 110 degrees Celsius and will not show any serious degradationii at this temperature. The maximum sustained operating temperature (at the bearing surface) is approximately 130 degrees Celsius for any oil formulated in the past 5 years and some high performance synthetics will not appreciably degrade even at this temperature. However, the degradation curve is a polynomial and degradation will increase rapidly with increasing temperature. According to the oil’s formulation (pure synthetics will show the least increase with temperature), by approximately 160 degrees Celsius (or about 300 degrees Fahrenheit), oil degradation can be up to 10 times faster then at 110 Deg. C. 2.4. Scale To fix the ‘number of bars’ problem, I determined that an overlay with numbers would be the best idea. 2.4.1. Addendum The number scale became too much to maintain. Rather than this, I cut a mm or so wide stripe out of the self sticking stripping meant for the side of a car. Using a red material, I put it through the middle of the fifth bar of both the temperature and fuel display. The stripe is slightly smaller than the thickness of the bar. This allows me to tell when I am at normal operating temperature and when approximately half a tank is used

Incoming search terms:

HARLEY DAVIDSON CHROME FORK SLIDERS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
REMOVAL 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s) and front wheel according to instructions found in the Chassis section of the appropriate service manual. NOTE On some models other parts will also need to be removed to access the front forks. See the service manual. 3. For All Models EXCEPT Touring: Drain and remove the front forks. See the service manual. 4. For Touring models equipped with air-adjustable suspension: Bleed the air-adjustable suspension according to the instructions in the appropriate service manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 5. For 2000 and Later Models EXCEPT Touring: See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side-to-side until it can be removed. Save reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. Peel off any excess adhesive from both reflectors . Surface must be clean for installation. 6. Disassemble the front fork tubes according to instructions in the service manual. INSTALLATION NOTES The chrome fork sliders included in this kit install in the same manner as the original equipment parts. Refer to the service manual for proper installation procedures. Prior to installation of this kit, check the bores of the new chrome sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Assemble the front fork tubes, replacing worn seals, bushings or other items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 2. Tighten the drain screws: •Early Models with 39 mm forks (see Figure 2): Tighten to 13-17 in-lbs (1.5-1.9 Nm) •Early Models with 41 mm forks (see Figure 2): Tighten to 52-78 in-lbs (5.8-8.8 Nm) •Later Models (see Figure 3): Tighten to 52-78 in-lbs (5.8- 8.8 Nm) 3. Fill with TYPE E FORK OIL (99884-80) according to the instructions in the service manual. 4. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel and caliper(s) according to instructions in the service manual. 5. For Touring models equipped with air-adjustable suspension: Refill the air-adjustable suspension system after assembly according to the service manual instruc- tions

Incoming search terms:

HARLEY DAVIDSON CENTER-MOUNTED LICENSE PLATE BRACKET KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (-) battery cable. Retain all seat mounting hardware. 2. Remove rear fender and side-mounted license plate bracket following the instructions in the Service Manual. INSTALLATION 1. Assemble and install the rear fender and the center- mounted license plate bracket following the instructions in the Service Manual. 2. Connect the license plate lamp connector following the instructions in the Service Manual. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 3. Install the seat and connect the negative (-) battery cable following the instructions in the Service Manual.

HARLEY DAVIDSON MINI-TACH WITH SHIFT LIGHT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION Preparation For EFI models: To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) Follow the instructions found in the Service Manual to purge the fuel supply of high pressure gasoline and remove the fuel supply line. For ALL models, WITH Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the Maxi-Fuse. For ALL models, WITHOUT Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. -J04106 Gasoline can drain fr om the carb uretor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) 2. For carbureted models: Turn the fuel supply valve to OFF. Remove the fuel line from the valve. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 3. For ALL models: Follow the instructions in the Service Manual to remove the instrument console from the fuel tank. 4. See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 5. For all models EXCEPT FLHR or 1986 and later FL Softail models with Chrome Headlight Nacelle Kit (Part Number 67907-96): Follow the instructions in the Service Manual to remove the headlamp housing. For FLHR models, or Softail models WITH the Nacelle Kit: Follow the instructions in the Service Manual and the mini-tach bracket kit (purchased separately) to remove the handlebar shroud. Mini-Tach Bracket Installation 6. For all models except FLHR: Install the mini-tach bracket components per the instructions in that kit. For FLHR models: Follow the instructions in the Service Manual and the mini-tach bracket kit to install the handlebar shroud and bracket components. 7. See Figure 7. Select the rubber isolation gasket (1) from this kit.

Incoming search terms:

HARLEY DAVIDSON ROAD ZEPPELIN SEAT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove main fuse following the instructions in the service manual. NOTE Cover the painted surfaces with protective material to prevent scratches or other damage. 2. Remove the left and right side saddlebags following the instructions in the owner’s manual. 3. See Figure 1. Remove the screw (1) and lockwashers (2) securing the grab strap (3) to the bracket (4 or 6). Save the hardware for installation. 4. Remove the grab strap. 5. Remove seat following the instructions in the service manual. -J04456 1 of 4 1 2 4 3 1 2 6 3 5 7 is06068 1. Stock screw 2. Stock lockwasher 3. Grab Strap 4. Bracket, 2009-Later Models 5.2009-Later Models 6. Bracket, 2008-Earlier Models 7.2008-Earlier Models Figure 1. Grab Strap and Saddlebag Front Mounting Bracket INSTALLATION 1. See Figure 2. Remove rubber plug from accessory connector (1) located under seat. Plug the seat electrical connector into the accessory connector. The connectors should lock together with an audible click. 2. Position the seat on the frame. Make sure the electrical harness and connector are not pinched between the seat and frame. 3. Install the seat following the instructions in the service manual.

Harley-Davidson FLOATING BRAKE ROTOR (DISC) KITS Removal and Disassembly

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Removal and Disassembly 2. Refer to FRONT WHEEL: REMOVAL or REAR WHEEL: REMOVAL in the Service Manual, and follow the instructions to remove the wheel from the motorcycle. Use a TORX® drive head to remove the screws retaining the currently installed brake disc to the wheel. The brake disc and screws can be discarded. 3. Inspect the wheel bearings per the PRELIMINARY INSPECTION instructions in the appropriate WHEEL section. Follow the DISASSEMBLY and CLEANING AND INSPECTION instructions as necessary to properly service the wheel. Reassembly and Installation Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 4. Refer to WHEEL: ASSEMBLY in the Service Manual, and follow the instructions to install the new brake disc to the wheel, using the new TORX screws from the kit. Complete the ASSEMBLY instructions as necessary to service the wheel. 5. Refer to WHEEL: INSTALLATION in the Service Manual, and follow the instructions to re-install the wheel to the motorcycle. Return to Service 6. Verify that the Ignition/Light Key Switch is turned to the OFF position. 7. Models WITH maxi-fuse: Refer to the Service Manual and follow the instructions given to re-install the maxi-fuse

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

Steering Stem Nut Installation Instructions & Owners Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
Sport Bike Damper Kit Installation Instructions DISCLAIMER: All GPR Sport Bike damper kits are manufactured to be used ONLY w/ the stock top triple clamp and frame. If either is modded, aftermarket or crash damaged, the kit will not install properly and GPR will not be held responsible for the consequences of improper installation due to this or any other improper mounting or modifying. The provided instructions must be followed precisely, as failure to do so can result in the GPR damper kit being installed incorrectly. An improper installation may lead to a variety of undesirable steering problems. Please take your time and carefully follow the installation instructions. As always, give us a call if you have any questions, we’re more than happy to assist you in getting the damper kit mounted on your bike properly 1. Remove the stock Steering Stem Nut (SSN) and washer from the stock top triple clamp steering stem. Carefully set the stock nut aside, as you may be using it later. Bikes requiring a specific GPR SSN to replace the stock SSN are listed at the end of this installation sheet. If your bike is on the chart, throw you stock SSN in the toolbox along w/ the washer, as you may need it at a later date if for any reason you need to remove the GPR kit from your bike. Stock SSN’s that are either ‘domed’ at the top or ‘flanged’ at the bottom will definitely NOT work, may lead to problems and should NOT be reinstalled during the baseplate installation. See #2 below for further instructions about both SSN/Steering stem and arm clearance issues 2. With the stock SSN and washer removed, place the GPR Baseplate over the steering stem on the top triple clamp and reinstall either the stock SSN or the GPR SSN provided. Torque SSN down to the recommended specs as per the owner’s manual for your particular bikes make and model. NEVER reinstall the stock washer that came on the bike! The baseplate is now your new washer. If you do accidentally use the stock washer, the arm on the stabilizer will most likely ‘rub’ on the nut. It will be too high, potentially locking the steering and handlebars, thus making your bike un steerable and unridable. DO NOT ride your bike until all installation steps have been completed and you can visually verify that there is clearance between the arm of the stabilizer and the steering stem and/or SSN. Once the installation is complete, at the #1 setting you

Incoming search terms:

Incoming search terms: