ironhead swingarm dimension

You search Auto repair manual PDF ironhead swingarm dimension, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ironhead swingarm dimension Direct Download speed 5282 Kb/s

  ironhead swingarm dimension Full Version speed 6162 Kb/s



240 tire V-Rod kit for stock swingarm Installation Instructions

0

Filed Under (Harley Davidson) by admin on 27-11-2010

download
Recommended Parts and Supplies 1. Sawzall or comparable cutting tool. 2. Cut-off tool or jigsaw. 3. Shop or repair manual 4. Shop supplies, (loctite-red and blue, anti-seize, etc.) 5. Assorted hand tools. 6. 4-1/2″ grinder. 7. Drive pulley seal HD part # 11354K (qty.1) 8. Copper cap locking plate HD part # 35451-01K (qty.1) (The seal and locking plate can be re-used if not damaged during removal) Stock component removal To install the 240 kit, it will be necessary to raise the motorcycle off the ground on a suitable lift. WARNING – Be sure to center the motorcycle on the lift so that it does not fall over when you raise it up or when you are working on it. Installation of the 240 kit begins with the disassembly and removal of the rear end of the bike. Start with the simplest and most obvious components. For detailed information on removal of these parts, consult your factory manual. 1. Remove rear wheel assembly and brake. 2. Remove swingarm. 3. Cut brake tab on swingarm (as pictured). 4 4. Clean up casting mark on inside of swingarm in pulley area (as pictured). 5 5. Remove and replace right side swingarm mount with mount included in kit. 6. Install swingarm with new supplied pivot shaft. 7. Install stock spacer on left side of shaft, use supplied stepped spacer between stock spacer and swingarm. (Small step toward bearing). 8. Remove front pulley, and disassemble. 9. Test fit ½” allen bolts in hub before removal. Some models require drilling for bolts to fit. If necessary, use ½” bit and drill before removing, minimal material will be removed. Take caution not to drill too deep and hit case. 6 10. Install supplied adapter on the back to space pulley out. (Use loctite on bolts, and assemble as pictured).

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SWINGARM PIVOT COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. Use rubbing alcohol to clean the swingarm surface, pivot bolt, and nut. 2. Place the larger left-side pivot cover (3) over the pivot nut. Position the set screw (4) at the bottom of the cover. Tighten set screw to 16 in-lbs (1.8 Nm) . 3. Remove adhesive backing from and apply the left-side trimplate to the swingarm. Apply pressure to the trimplate on the swingarm for one minute. 4. Remove adhesive backing from and apply an emblem to the center of the pivot cover. Apply pressure to the emblem for one minute. 5. Repeat Steps 1-4 for the right side of the swingarm. 6. Allow adhesive to cure for 24 hours before operating the vehicle. SERVICE PARTS 4 2 5 3 1 5 6 3 is01811 Figure 1. Service Parts: Swingarm Pivot Cover Kit Table 1. Service Parts: Swingarm Pivot Cover Kit Part Number Description (Quantity) Item Not Sold Separately Right-side trimplate and adhe- sive 1 Not Sold Separately Left-side trimplate and adhesive 2 Not Sold Separately Adhesive emblem (2) 3 Not Sold Separately Left-side pivot cover 4 3231B Set screw (2) 5 Not Sold Separately

YAMAHA SINGLE SIDED SWINGARM REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 27-12-2011

download
1. Disconnect Battery 2. Lift and secure bike 3. Remove brake-side floorboard 4. Remove exhaust. 5. Remove rear fender 6. Remove front pulley cover 7. Remove wheel, pulley, and brake assembly simultaneously. Now remove front pulley from transmission. (Keep up with the stock nut and lock washer; these will be used during assembly) 8. Remove Passenger pegs; now remove the plastic covers in the frame that cover the pivot tube bolts. 9. Remove the stock shock bolts ( keep for re-assembly) 10. Remove the pivot tube bolts. 11. Remove the stock swingarmb12. Install “new” belt at this time. 13. Install supplied pivot tube, and bearings in RC swingarm. 14. Install shock bolt with red loctite in RC swingarm. (Do not tighten bolt at this time) 15. Insert supplied pivot bolts with red loctite through frame and supplied bushings into the RC swingarm. (Right side bushing has flats) 16. Torque shock and pivot bolts to factory specs. 17. Install belt adjustment bolts and single side keys into swingarm.

HARLEY DAVIDSON DYNA CHROME SWINGARM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
This kit fits all 2006 and later Dyna model motorcycles. INSTALLATION NOTE Refer to the appropriate Service Manual for detailed information on the following generalized steps. 1. Remove the rear fork. 2. Remove the bearing, spacer and retaining ring from left side pivot bore of the stock swingarm. 3. Install the bearing, spacer and retaining ring removed in the previous step, into the left side pivot bore of the chrome swingarm. 4. Install the dust shield and bushing, from the kit, into right side pivot bore of the chrome swingarm. 5. Install the chrome swingarm kit. SERVICE PARTS

HARLEY DAVIDSON REAR SWINGARM AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE XL Sportster 883 and XL1200R models may require loosening or removal of the rear muffler in order to install the right side rear axle cover. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. 1. Support the vehicle, and loosen or remove the rear muffler if necessary. XL Sportster 883 and XL1200R models: Remove the right-side lower shock absorber mounting bolt. Save for re-installation. All other models: Remove and discard the right-side lower shock absorber mounting bolt. 2. Swing the bottom of the shock absorber out of the way. Position the right-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 3. Reposition the shock absorber. XL Sportster 883 and XL1200R models: Install the shock absorber mounting bolt removed in Step 1. All other models: Install the shoulder bolt (3) from the kit. All models: Tighten the bolt to 45-50 ft-lbs (61-68 Nm) . NOTE When torquing the bolt, align two of the bolt-head flats parallel to the ground. This will allow proper orientation of the bar and shield logo on the bolt cover. 4. Position the bolt cover (4) over the bolt head (3) with the Bar-and-Shield logo oriented upright, and lock in place with the set screw (5). Tighten securely. Reposition and tighten the muffler per the Service Manual instructions. 5. Remove and discard the left-side lower shock absorber mounting bolt. Move the bottom of the shock absorber out of the way. Position the left-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 6. Reposition the shock absorber and install the shoulder bolt from the kit. Tighten to 45-50 ft-lbs (61-68 Nm) , aligning two of the bolt head flats parallel to the ground. 7. Position the bolt cover over the bolt head with the Bar-and- Shield logo oriented upright, and lock in place with the set screw. Tighten securely

Suzuki 240 Hayabusa Swingarm Installation Instructions

0

Filed Under (Suzuki) by admin on 12-02-2012

download
installation Instructions 1.) Stock Component Removal To begin installing this kit it is necessary to raise the rear end of the bike using a suitable hoist. Be sure to keep the bike centered on the front wheel to keep the bike from tipping over. Once you have the bike lifted and properly secured, begin with the removal of the following stock components ( For detailed information on the removal of these parts, please consult your factory manual) : 1.) Muffler or mufflers 2.) Left side and lower body panels 3.) Voltage regulator (08 model only) 4.) Front sprocket cover 5.) Front sprocket 6.) Chain 7.) Rear Axel, wheel and brake assembly 8.) Pivot tube and swingarm
2.) New Swingarm Installation A. Most of the pieces needed are installed on the swing-arm. You’ll need to install the shock mount block with the 4 supplied flat head 5/16″bolts, use red loctite and torque to 25 ft lbs. B. Insert the 2 supplied pivot bushings in the pivot tube. Move your new swingarm into position. Once you have the swingarm in position reinsert the pivot tube to hold it in place. C. On some bikes (07′ and earlier Busa’s) it is necessary to grind approximately 1/8″ off the frame for chain clearance. Not all bikes will require this, but it is best to mock up and test fit before final assembly.

Incoming search terms:

INSTRUCTIONS ON HOW TO R & R YOUR Swingarm

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
• Upgrade Your Pre- 2002 FL Or FXR Rear Fork & Get Rid Of The Crappy & Dangerous (Cleve Blocks) & Replace Them With A Stable System. • R & R your Swing Arm, Belt Drive, Swing Arm Pivot Shaft, and Rear Wheel. The paragraphs below are a photo journey into the replacement of a FL or FXR swing arm. To upgrade the pre 2002 FL, here is a How-To on cheaply replacing the poor parts Harley stuck you with. Now – Let’s Get Er’ Done • Pre- 2002 had weak swing arms and are known to fail. The cleve blocks are the cause of “Rear Steer” or “Rear Fork Deflection”. Harley came up with a patch in 2002, using bearings. Because the pre 2002 transmissions have a 5/8″ mounting hole for the 5/8″ swing arm pivot shaft, a conversion unit has been made. No transmission removal for boring is necessary. Under no circumstances, do I recommend drilling out the transmission case with a hand drill. The drill will “wander” (drift)! • Solution: Go to either a trike shop/manufacturer, e-Bay, or shop and buy a new style swingarm. Harley made an additional upgrade in 2007, try and buy this type 2007 & above). If upgrading to a 2008, Harley use 25mm (smaller than 1″) axles & wheel bearings, you will have to use 25mm bearings. With that said, let’s get on with it. • In the case of a 2007 swingarm; buy and do not pay over $40 for the swing arm and axle. You must use the corresponding axle as a ¾” axle set-up is different (along with wheel bearings & spacers). You positively can not use a pre -2002 HD stock wheel because the wheel bearing spacer will fit into the wheel. Buy 2002 & above style wheels as they (9 spoke) are cheep. • You are going to have to either bore out your stock rear caliper bracket or better still, upgrade your whole rear brake to the new model & sell yours on e-Bay. • I recommend doing the following before hand and have it ready for installation; Remove bearings et al. from the 2002 & later swing arm via press. Bike Work: • Jack up your bike using a center jack. Secure the bike so it will not fall over. You can also use a motorcycle jack. I use a motorcycle dolly

HARLEY DAVIDSON STAINLESS STEEL SPLASHGUARD INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

1. Refer to the appropriate Service Manual and remove the Maxi® fuse. 2. Refer to the applicable Service Manual and remove the rear wheel. 3. See Figure 1. Remove one screw (1) and stock splash- guard (2) from swingarm (3). 4. Remove the protective film from the new splashguard. 5. See Figure 4. Using two screws (4) and nuts (2), loosely install the H-clips to the back of the splash guard vertically as shown. 2 1 3 is04881 1. P-clamp 2. Splashguard 3. Raised bar of swingarm Figure 2. Install Splashguard -J04271 1 of 2 1 3 2 4 5 is04892 1. H-clip 2. Swingarm 3. Splashguard 4. Screw 5. Nut Figure 3. H-Clips Installed on Swingarm 6. See Figure 2. Slide two P-clamps (1) around the upper bar of the rear fork. The straight side of the clamp will face rearward, as shown in Figure 4. 7. See Figure 4. Orient the splashguard with the polished side facing the rear wheel. Align the upper two holes with the P-clamp holes. Secure splashguard to the P-clips with two screws (4) and locknuts (2). Do not tighten at this time. 8. See Figure 3. Turn H-clips (1) horizontal on the splash- guard. Press splashguard (3) into place. When the splashguard is in place, rotate the H-clips down over the raise bar of the swingarm (2). Tighten the screw (4) and nut (5) to secure the H-clips. NOTE If adequate clearance does not exist between the splashguard and rear brake line and drive belt, adjust fender extension by loosening hardware and centering the splashguard. 9. See Figure 4. Ensure the splashguard does not touch the drive belt on the left side and the rear brake line on the right side, then tighten P-clip mounting screws (4) and nuts (2) securely. 10. Refer to the applicable Service Manual and install the rear wheel. 11. Refer to the appropriate Service Manual and install the Maxi fuse

240 Sport Bike Swingarm Installation Instructions

0

Filed Under (Tips and Review) by admin on 02-12-2010

download
Motorcycles can be dangerous if not properly maintained and ridden safely. RC Components has no control over the usage of any of its parts. RC Components expects its customers to exercise good judgment as to the proper selection, installation, use, and maintenance of any parts. RC Components assumes no responsibility for damage or injury of any kind because of the misuse or improper application of any parts in any way by any person. RC Components expects the end user to exercise good judgment. • Before installing this kit, read through these directions completely. This will familiarize you with the way in which the parts fit together and the tools needed to complete the job. • Before performing any installation steps, disconnect the motorcycle’s battery to eliminate any possibility of electrical damage or personal injury due to a short circuit. Part Number: NSTSB240 Page 2 of 12 Materials Needed: • Hardware Kit. Kit includes (See picture below): 04-05 GSXR750-600 & 03-04 GSXR1000 Kit Inboard Brake Kit Part Number: INSTSB240 Page 3 of 12 04-05 GSXR750-600 & 03-04 GSXR1000 Kit for Stock Caliper 08 Busa Kit for Inboard Brake Part Number: INSTSB240 Page 4 of 12 05-06 GSXR 1000 Kit for Inboard Brake
Part Number: INSTSB240 Page 5 of 12 05-06 GSXR1000 Kit for Stock Caliper 99-07 Busa Kit for Inboard Brake
Part Number: INSTSB240 Page 6 of 12 99-07 Busa Kit for Stock Caliper Tools Needed: • Bike Specific Service Manual (Refer to manual for all torque specs and tools that are not specified by RC Components.) • Assorted hand tools, metric and standard sockets and wrenches. • Hoist or other means to lift bike. • Torque wrench • Loctite, and anti-seize • Chain breaker • Bike specific sockets are required for some bikes. (Refer to factory service manual). • Die grinder (for chain to frame clearance on some models) Installation Instructions 1.) Stock Component Removal To begin installing this kit it is necessary to raise the rear end of the bike using a suitable hoist. Be sure to keep the bike centered on the front wheel to keep the bike from tipping over. Once you have the bike lifted and properly secured, begin with the removal of the following stock components ( For detailed information on the removal of these parts, please consult your factory manual) : 1.) Muffler or mufflers 2.) Left side and lower body panels 3.) Voltage regulator (08 model only) 4.) Front sprocket cover 5.) Front sprocket 6.) Chain

KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 23-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove right side frame cover. 2. If motorcycle is oxygen sensor equipped, remove passenger seat. Remove two bolts securing operator seat and set seat aside. Locate and unplug oxygen sensor connector from wiring harness (Figure 1).(Note wire routing for reassembly). 3. Remove right side floorboard assembly held in place by two bolts (Figure 2). 4. Remove exhaust port flange nuts. 5. Remove flange bolts securing rear muffler to exhaust system mounting bracket. 6. Remove complete exhaust system. Start by removing front head pipe from exhaust port (assistance may be required). Page 1of 4 K400IN Rev. 1.1 KAWASAKI VULCAN 2000 POWERSHOTS EXHAUST SYSTEM Part #18311 Tools required for installations 6mm Allen wrench 8mm 12mm 14mm sockets 3/8″ Ratchet & Extensions 19mm Wrench 9/16 Wrench Brake bleeder & fluid
7. Check condition of stock exhaust gaskets. Replace if damaged or worn. 8. Remove plastic hose clamp securing rear brake hose to swingarm.Save for re-use. 9. Remove brake hose banjo bolt from rear caliper. 10. Slide hose out of loops in swingarm. 11. Remove three bolts holding stock exhaust mounting bracket and slide bracket off end of brake hose. 12. Slide brake hose through loop on new bracket (stamped 357-P) and install to the original mounting bracket location, using three 8mm x 16mm Allen bolts (supplied) (Figure 3). 13. Check condition of sealing washers on banjo bolt and replace if damaged or worn. 14. Slide brake hose through loops on swingarm and reconnect brake hose to caliper. 15. Reinstall plastic clip onto swingarm. 16. Brake system must be bled or brake will not operate correctly.

Incoming search terms:

Incoming search terms: