is timing on 1995 cr250 adjustable

You search Auto repair manual PDF is timing on 1995 cr250 adjustable, if there are search results will appear below. If search results do not exist, please search by others keyword.



  is timing on 1995 cr250 adjustable Direct Download speed 5282 Kb/s

  is timing on 1995 cr250 adjustable Full Version speed 6162 Kb/s



ULTIMA IGNITION MODULE AND KIT INSTALLATION MANUAL FOR HARLEY DAVIDSON

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
Disconnect battery. 2. Mark location of timing plate in relation to inside of cam cover. This will give a starting point for timing on new module. Remove old ignition if applicable (see manual) Clymer, Haynes. 3. If your bike is not equipped with timing rotor M/W# 53-528 OEM#32402-83 you must buy one (included in kit). Also a single fire coil is needed (included in kit) M/W# 53-632. Any single fire coil rated 2-4 ohms can be used. NO SOLID CORE PLUG WIRES (copper, silver) they will damage the unit. 4. Install module: helpful hints, early model nose cones, i.e. Shovel Heads, the hole for the wire may need to be drilled out. Align with previously scripted mark for timing. Use lockwashers for stand offs for correct clearance of cover plate. Run wire loom. 5. Connect wires, see wiring diagram. Tape unused wires, green or brown. 12v to tach (brown) will damage module. Set timing. 1996 and later should not be timed 20˚ BTDC as the OEM module, but at 35˚ BTDC. Use this mark when using timing light. If VOESswitch is not used you must ground VOES wire (green) while timing. Refer to manual for correct identification of timing marks. At start up and timing, set spark advance in middle position. FUNCTION SWITCHES LED timing indicator light: When out, shows TDC. When ignition is on, LED will light up. When engine is cranking LED will blink. Electric Start/Kickstart: Set accordingly. VOES/Race mode: VOES switch lets the motor run smoother and improves gas mileage. If you don’t use it or add one tape up green wire and switch to race. VOES switch to use, M/W# 53-652. Spark advance: High compression motors should use race mode and 93 octane or better gas. Changing from VOES to race changes advance curves. Agood rule of thumb is if the engine knocks when throttle is applied in high gear, turn back spark advance curve until it stops engine knock. RPMlimiter: Set at desired RPM to cut engine power. Rear Cylinder: This is for racing and should be set at a dyno. +/-5˚. Rear cylinder timing is achieved through this adjuster. Most should dial to middle setting and leave alone. After all switches are set, install cover with supplied gasket and feel the increased performance of a solid state single fire ignition. Again, we remind you, if you don’t feel confident about installing this unit, let a qualified mechanic do it and be assured you are getting the best performance and gas mileage possible.

Incoming search terms:

Toyota Camry, Celica, Corolla, MR2 (1995), Paseo, Pickup (1995), RAV4 (1996), Supra, Tacoma, Tercel, T100, 4Runner TRANSMISSION REMOVAL & INSTALLATION – M/ T

0

Filed Under (Toyota Manuals) by admin on 22-06-2011

Download
Disconnect negative battery cable. On 2.2L (5S-FE) models,
remove battery and cruise control actuator. On all models, remove air
cleaner case with air intake hose. Remove clutch release cylinder with
hose attached and secure aside.
2) Remove starter. Disconnect necessary ground straps,
electrical connections and control cables from transaxle. Remove upper
transaxle mounting bolts from cylinder block.
3) Raise and support vehicle. Remove front wheels. Remove
lower engine covers. Drain transaxle fluid. Remove axle shafts from
transaxle. See AXLE SHAFTS article in AXLE SHAFTS & TRANSFER CASES
section

Incoming search terms:

YAMAHA XS650H/ SH Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 21-11-2010

download
Ignition timing check 1. Ignition timing is checked with a timing light by observing the position of the rotor pointer and the marks stamped on the timing plate. The timing plate is marked as follows. “ll” Firing range for No. 1 (L.H.) “T” Top Dead Center for No. 1, fL.H.1 cylinder 2. Connect the timing light to the left cylinder spark plug lead wire. 3. Start the engine and keep the engine speed as specified. Use a tachometer to check the engine speed. B. PICK-UP COIL ASSEMBLY The method of mounting the pick-up coil assembly is changed for easier service work. Thus, the followings “Pick-up coil assembly removal” and “Pick-up coil assembly reinstallation” should be changed. Pick-up coil assembly removal Remove the pick-up coil securing screws and remove the pick-up coil assembly. Pick-up coil assembly reinstallation Install the pick-up coil assembly on to the stator assembly. _ L 4. Specified engine speed: 1,200 r/min The rotor pointer should be within the limits of ” fl ” on the timing plate. If it exceeds the limits or does not steady, check the timing plate for tight- ness and/or ignition system for damage. NOTE: Ignition timing is not adjustable. C. FUEL LEVEL The carburetor is furnished with a drain screw to provide easy access to service work. Thus, the following “Fuel level measurement” should be added. Fuel level measurement NOTE: Before checking the fuel level, note the follow- ing: 1. Place the motorcycle on a level surface. 2. Adjust the motorcycle position by placing a suitable stand or a garage jack under the engine so that the carburetor is positioned vertically. 1. 2. Connect the level gauge (special tool) or a vinyl pipe of 6 mm (0.24 in) in inside diameter to the float bowl nozzle left or right side carburetor. Set the gauge as shown and loosen the drain screw 3. Start the engine and stop it after a few minutes of run. This procedure is neces- sary to obtain the correct fuel level. NOTE: Make sure the fuel petcock is “ON” or “RES” oosition. 4. Note the fuel level and bring the gauge to the other end of the carburetor line and repeat step 3 above. Note the fuel level again and compare it with the previous gauge reading. They should be equal. If not, place a suitable size of wooden piece or the. alike under the center stand and adjust. 5. Check the fuel level one by one. The level should be in the specified range.

Incoming search terms:

HARLEY DAVIDSON ADJUSTABLE AIR DEFLECTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. See Figure 1. Models with NO air deflectors installed: Remove and discard the eight hole plugs (1) from the right and left edges of the inner fairing assembly. Models WITH air deflectors currently installed: Remove and discard the eight screws that retain the right and left air deflectors. Remove and discard the deflectors. 2. See Figure 2. Select a right-side (1) or left-side (2) air deflector, and four screws (3) from the kit. Determine the correct side by holding the mounting-hole side of the deflector against the fairing. 3. Place the deflector against the inner fairing, lining up the holes. Insert the screws through the deflector holes and into the fairing air deflector holes. Tighten the screws to 25-30 in-lbs (2.8-3.4 Nm) . 1 1 is04653a Figure 1. Remove Hole Plugs SERVICE PARTS 3 2 1 is04654 Figure 2. Service Parts: Adjustable Air Deflector Kit Table 1. Service Parts Table Part Number Description (Quantity) Item 58128-08A Air deflector, adjustable (right side) – Dark Smoke 1 57655-08A Air deflector, adjustable (right side) – Light Smoke 58129-08A Air deflector, adjustable (left side) – Dark Smoke 2 57657-08A Air deflector, adjustable (left side) – Light Smoke 2563 Screw (8

Incoming search terms:

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

4-STROKE TRIUMPH SINGLE CYLINDER MOTORCYCLES ELECTRONIC IGNITION SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 27-10-2010

download
1. Remove the petrol tank (and seat if necessary) to gain access to the ignition coil, condensor and wiring. 2. For safety, disconnect the battery, if fitted (preferably both terminals). 3. Remove the spark plug. 4. Remove the alternator rotor cover (if fitted). 5. Loosen the auto-advance centre bolt. Rotate the engine to the correct full advance timing position for your machine (see table on page 6), using one of these methods: • Models from 1967 on: use the marks provided for strobe timing on the rotor & chaincase (inside the rotor cover). Unless these marks are known to be accurate it is recommended that they are checked for correct alignment. These marks should line up at the full advance position, check using one of the methods below and, if necessary, re-mark the rotor. • Models from 1969 on: use the timing plug on the left-hand crankcase • Use a degree disc on the crankshaft / camshaft (see table on page 6) • Use a dial guage down the spark plug hole (see table on page 6) 5. Remove kickstart, gear lever and outer timing cover. 6. Remove the contact-breaker plate and lead from the outer timing cover. 7. Taking the ignition trigger assembly, insert a small cable tie into the two holes in front of the connector block on the ignition trigger. This will be used later to secure the two wires to the plate. 8. Fit the ignition trigger plate with the adjustable slots at approx. 6 & 12 o’clock, using the original pillar fixings & washers, positioned in the centre of the slots (to allow for adjustment in either direction). Handle the trigger with care. • RED EARTHING WIRE • CRIMP CONNECTORS & INSULATORS • LARGE & SMALL CABLE TIES • CABLE TIE ADHESIVE MOUNTING BASE 3
9. Remove the centre bolt securing the auto-advance unit. Remove the complete auto-advance unit with an extractor bolt or by tapping it gently sideways. 10. Fit the magnetic rotor in place of the auto-advance unit, with the magnets/ red marks positioned at approx. 3 & 9 o’clock. The magnetic rotor has a male taper which fits into the taper in the end of the camshaft. There is no keyway, allowing it to be fitted in any desired position. 11. Using the ¼” washer and the appropriate bolt (UNF or BSF), pass the bolt through the centre of the magnetic rotor and into the thread in the camshaft. Finger tighten only at this stage. The magnetic rotor centre thread (metric M8) is provided for attaching a puller, if the rotor should need to be removed for engine servicing, etc. 12. Replace the outer timing cover, gear lever & kickstart. 13. Check that the engine is still at the correct full advance position, then adjust the magnetic rotor position so that one of the red marks is centrally behind the static timing hole at 9 o’clock (see fig. 4, page 7). If your machine’s camshaft rotates clockwise, refer to fig. 3. Gently tap the rotor into the taper & tighten the centre bolt, using a 3/16″ allen key. WIRING: 14. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. Avoid coiling up surplus lead.

Incoming search terms:

HARLEY DAVIDSON FXD (Dyna Super Glide) TACHOMETER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
1995 Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1.1995 MODELS, REMOVAL OF ELECTRONIC SPEEDOMETER AND BRACKET 1a. Refer to applicable Service Manual procedure and remove seat. 1b. Refer to applicable Service Manual procedure and remove fuel tank. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 1c. Remove speedometer sensor cable from mounting clips under tank. See Figure 1. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Cut cable tie holding sensor wires to right rear frame tube. 1d. Refer to applicable Service Manual procedure and remove headlamp, for work clearance. 1e Remove handlebar clamp screws securing speedometer bracket. Remove speedometer, bracket, and harness. 2.1995 MODELS, DISCONNECT MAIN WIRING HARNESS 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 2a. Disconnect the battery, negative cable first. Refer to applicable Service Manual procedure and disconnect main wiring harness 8-place connector [21A, B], at the front of the motorcycle. 3.1995 MODELS, REMOVE SPEEDOMETER LEADS FROM 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 3a. See Figure 2 and Service Manual wiring schematic. Pull the following wires and terminals out of connector [21B]. Wire Color Cavity Number Orange/white 5 White/green 1 Black 2 3b. Remove the large female connector from the fuel gauge black wire. 3c. Slide the wires removed in step 2a out of the plastic conduit covering the wires connected to the 8-place connector. 1 WARNING 1 WARNING 1 WARNING Figure 1. Speedometer Sensor Connection [65] 4973 Speedometer sensor connector [65] Figure 2. Tachometer/Speedometer Wire Splices and Terminal Connections [21B, A] i00240-.tif Splices 4.1995 MODELS, REMOVE INDICATOR LAMPS FROM BRACKET 4a. Remove the screws that secure the indicator lamps assembly to the speedometer bracket. Retain screws and indicator lamps assembly for installation on speedometer/tachometer bracket later. 5.1995 MODELS, REMOVE SPEEDOMETER FROM BRACKET 5a. Unscrew boot from speedometer reset switch. Remove cover screws and rear cover. 5b. See Figure 3. Note position of rear speedometer gasket and remove it. Push on rear of speedometer while simultaneously pulling speedometer and front gasket from bracket. Do not remove front gasket from the speedometer. 6.1995 MODELS, INSTALL SPEEDOMETER IN KIT BRACKET 6a. See Figure 5. Place wires from speedometer through front of left opening in double bracket. Lubricate the front and rear gaskets with isopropyl alcohol or glass cleaner to ease installation. 6b. Insert speedometer into the front of the double bracket. Be sure wire guides are aligned with opening at bottom of bracket. 6c. Place rear gasket in position and align gasket tabs. Work gasket into space between speedometer and bracket by pushing speedometer against one side of bracket while pushing gasket into position at the opposite side. 6d. Add amber bulb assembly from kit to speedometer in order for tachometer and speedometer backlighting to match. 6e. Replace cover and boot from reset switch.

Incoming search terms:

2003 Ducati ST4s Timing Belt Adjustment

0

Filed Under (Aprilia) by admin on 31-10-2010

download
This instruction on cam belt adjustment starts after you remove the fairing pieces. Plan on an hour to remove these. Since you are performing your own service, buying Ducati belts may not be that expensive. There may be another belt source, but I have not confirmed this for the 996 engine of the 02-03 ST4s. Fig 1 – ST4s ready for belt adj./ repl. Fig 2 – Crank tool installed. See dwg. 1) Ensure maximum of ½ tank of gas. Fuel will leak into the charcoal canister, then onto the floor if the tank is over half full and the tank is tilted up on its hinge. So put the tank up on its hinge. 2) Remove spark plugs. Cover sparkplug wells with boots or rags. This is a great time to toss out those Champions for a set of NGK DCPR8E’s. 3) Remove the front shield from the horizontal cylinder head. 4) Remove crankshaft cover on Riders LH side and insert crank tool. A crank tool can be made by following the drawing at the end of this document. See Fig 2 above. The flat head screws used are kind of soft so beware on their removal. 5) Remove oil pressure sending unit cable and remove oil sending unit. No oil should pour out. 6) Remove battery and remove bolts fastening battery box to engine/frame. You can let the battery box dangle or partially support it via a bungee cord. Be careful of the cable on the ground of the ECU. By dangling the battery box excess stress could be placed on this cables connector and you don’t want to troubleshoot an intermittent electrical issue. 7) Remove cam belt covers. The two covers over the cams are real easy. The center piece is removed by pulling it down. You may have to move some hoses and cables out Timing belt adj. doc 1
of the way because it is a tight fit. Removing the oil pressure sending unit gave clearance for the removal. Fig 1 shows bike ready to be worked on. On the Rider’s LH is a window on the case cover. Using a flashlight to illuminate the area, marks can be rotated into view using the engine turning tool. There are two marks denoting the TDC of each of the cylinders. When a mark in the window aligns with the pointer, look at the crank driving pulley on the Rider’s RH of the engine. If the driving pulley’s mark is aligned with the pointer on the engine case, you are at TDC horizontal cylinder. If the pulley mark and the pointer on the engine do not align, rotate the engine until the mark in the window on the Rider’s LH side case cover aligns as well as the pulley’s mark and the engine’s pointer. Fig 3 shows the engine pulley and pointer. You can check that the horizontal piston is at TDC by inserting a welding rod into the spark plug well and touch the top of the piston with it to sense its position. Timing marks on cam pulleys are clearly stamped on all four pulleys. When the crank driving pulley aligns with its corresponding pointer on the engine case and the marks on the pulleys align with their corresponding marks on both cylinders, you are in position for belt adjustment and replacement

Incoming search terms:

2003 – 2007 4Runner OIL LEAK FROM FRONT TIMING COVER

0

Filed Under (Toyota Manuals) by admin on 31-10-2011

download
evidence of a small oil leak located where the Bank 1 cylinder head, engine block, and timing cover meet. Use the following repair procedure to address this condition. 2003 – 2007 model year 4Runner vehicles equipped with the 1GR-FE engine and produced BEFORE the Production Change Effective VINs shown below. MODEL PLANT DRIVETRAIN PRODUCTION CHANGE EFFECTIVE VIN 2WD JTEZU17R#68064608 Hino 2WD JTEZU14R#78076191 4Runner Hino 4WD JTEBU14R#78078323 4Runner 4WD JTEBU14R#78090468 Tahara 2WD JTEZU14R#70091230 Tahara 4WD JTEBU14R#70117349 OP CODE DESCRIPTION TIME OFP T1 T2 EG7036 Reseal FrontTiming Cover with FIPG 2WD7.6 113100P0306548 EG7036 Reseal Front Timing Cover with FIPG 4WD8.5 11310-0P030 65 48 Applicable Warranty*: This repair is covered under the Toyota Powertrain Warranty. This warranty is in effect for 60 months or 60,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

2011 Ninja ZX-10R Review And SPECIFICATIONS

0

Filed Under (Kawasaki) by admin on 13-12-2010

download
1. Big Piston Fork (BPF) and Öhlins Steering Damper Throwing out the anchors at track speed demands a fork that remains composed under pressure. The fully adjustable new Big Piston Fork (BPF) does just that by significantly reducing damping pressure while maintaining consistent damping force. The standard Öhlins Steering Damper is likewise adjustable to help you dial in the steering damping level you need. 2. Horizontal Back-Link Rear Suspension New rear suspension positions the shock and its linkage above the swingarm, leaving room beneath the bike for a larger exhaust pre-chamber. The move helps centralize mass for better transitional cornering response, while also improving overall suspension action and road holding. The piggyback-reservoir shock is fully adjustable, including both low- and high-speed compression-damping circuits. 3. Adjustable Footpegs Adapting the ZX-10R for a day at the track or a long street ride is easy, thanks to its new adjustable footpegs. Raise the footpegs to improve your cornering clearance on the track, or lower them for a more relaxed riding position on the street or highway. The total range of adjustment is 15mm. 1. 2. 3. SPECIFICATIONS Engine Four-stroke, liquid-cooled, DOHC, four valves per cylinder, inline-four Displacement 998cc Bore X Stroke 76.0 x 55.0 mm Compression Ratio 13.0:1 Fuel System DFI® with four 47mm Keihin throttle bodies with oval sub-throttles, two injectors per cylinder Ignition TCBI with digital advance and Sport-Kawasaki Traction Control (S-KTRC) Transmission Six-speed Final Drive Chain Rake/Trail 25.0deg / 4.33 in. Front Tire Size 120/70 ZR17 Rear Tire Size 190/55 ZR17 Wheelbase 56.1 in. Front Suspension / Wheel Travel 43mm inverted Big Piston Fork (BPF) with DLC coating, adjustable rebound and compression damping, spring preload adjustability / 4.7 in. Rear Suspension / Wheel Travel Horizontal Back-link with gas-charged shock and top-out spring, stepless, dual-range (low-/high- speed) compression damping, stepless rebound damping, fully adjustable spring preload / 4.9 in. Front Brakes Kawasaki Intelligent anti-lock Braking (KIBS), dual semi-floating 310mm petal discs with dual four-piston radial-mount calipers Rear Brakes KIBS-controlled, single 220mm petal disc with aluminum single-piston caliper Fuel Capacity 4.5 gal. Seat Height 32.0 in. Curb Weight TBD Overall Length 81.7 in. Overall Width 28.2 in. Overall Height 43.9 in. Color Choices Lime Green / Ebony, Ebony / Flat Ebony Warranty 12 Months Good Times™ Protection Plan 12, 24, 36, 48 months PERFORMANCE PARTS Kawasaki offers a full line of performance parts for your new motorcycle. COVER Constructed of water-resistant polyester and a unique shielded vent system that allows built-up moisture to vent. Reinforced grommet at the bottom hem allows the cover to be locked to the bike for added security. Heat resistant panels in the exhaust area. Oversized fit allows for easy installation and removal.

Incoming search terms:

Incoming search terms: