jet sizes for suzuki intruder 1400

You search Auto repair manual PDF jet sizes for suzuki intruder 1400, if there are search results will appear below. If search results do not exist, please search by others keyword.



  jet sizes for suzuki intruder 1400 Direct Download speed 5282 Kb/s

  jet sizes for suzuki intruder 1400 Full Version speed 6162 Kb/s



Triumph SU CARBURETORS SERVICING AND TUNING

0

Filed Under (Triumph) by admin on 29-10-2010

download
Jets: These are made in various sizes ranging from.099 inches to.1875 inches, the larger sizes being used only for racing or very high performance engines. The two sizes most commonly found on production cars are the.090 inch and the.100 inch. The size of the jet will be found stamped on the jet head. The figure “nine”wilt indicate that it is the.090 inch and the figure “one”will indicate the.100 inch jet. When tuninga production car the jets size should be checked to make sure that it is of the size recommended by the manufacturers. Centering of Jet: If for any reason, the jet assembly has been removed, it will be ne cessary to recenter the jet. First, remove the clevis pin at the base of the jet which attaches the jet head to the jet operating lever. Withdraw the jet completely and remove the adjusting nut and spring, then replace the adjusting nut, without its spring, and screw it up toits highest position. Slide the Set into position until the jet head is against the base of the adjusting nut. When this has been done, find out if the piston is perfectly free by lifting it up with the finger and allowing it to drop. If the piston is not entirely free, slacken the jet screw and manipulate the lower part of the assembly, including the projecting part of the bottom half of the jet bearing, adjusting nut, and jet head. Make sure that this assembly is now slightly loose. The piston should then rise and fall quite freely as the needle is now able to move the jet into the required central position. The jet screw should now be tightened and a further check made to determine that the piston is still quite free. When complete freedom of the piston is achieved the jet adjusting nut should be removed, together with the jet, and the spring replaced. Experience has shown that a large percentage of carburetors, which have given trouble has been due to the incorrect centering of jets. Jet Needles— These are made in a great variety of sizes, probably now well over two hundred and fifty, and each type of engine hasaneedlethat has been selected, after very careful tests have been carried out, to give the best all-round performance. Most manufacturers actually give three alternative needles for each type and size of engine, these needles clearly being listed by the manufacturer “Standard”, “Rich”or”Weak”and before tuning is started the needle, which is marked on the shank should be checked against the manufacturer’srecommendation to make quite sure that the right needle is fitted; this is most important.

Incoming search terms:

SUZUKI 1400/ 800 INTRUDER TURN SIGNAL RELOCATION INSTALLATION AND CLEANING INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 09-11-2010

download
1. Refer to Figure 1. 2. Remove seat. Safety: disconnect battery prior to all wiring modifications LeatherLyke 510 5/1/2009 3. Disconnect wires to turn signals. 4. Remove turn signals and retain hardware for reinstallation. Observe and mark “left” and “right” for reinstallation. Information: Do not remove license plate bracket . 5. Remove license plate. Turn signal bracket must be oriented with flange (side with only 2 holes) on top. 6. Install turn signal bracket behind license plate bracket and license plate using 6 x 35mm pan phil machine screws for the 800 or 6 x 20mm pan phil machine screws for the 1400, 1/4″ flat washers, and 6mm locknuts. Insert black spacer spool between license plate bracket and turn signal bracket. 7. Mount turn signals directly to turn signal bracket using 6 x 10mm hex cap screws and star lock washer. Information: Observe all color-coding of wires and splice one wire at a time. 8. Cut each turn signal wires three inches from end and splice 10 inches of supplied wire. Secure wires to inner fender clips. 9. Follow route of tail light wires and connect wires into harness. 10. Secure wires together behind license plate bracket with tie wrap. 11. Connect battery and test turn signals for function. 12. Install seat. Information: Not all license plate mounts are grounded. In some cases, it may be necessary to run a ground wire to turn signal bracket. WARNING: States may have minimum width requirements on motorcycle turn- signals, so check your local laws. LeatherLyke 510 5/1/2009 SADDLEBAG INSTALLATION 13. Refer to Figure 2. Information: Cover plates are pressed into strut. 14. Remove round cover plate at end of fender mount strut on right side. 15. Remove nut on right rear and replace with 1.2″ hex adapter. If hex adapter is less than flush with the outside of both fender struts, add a 5/16″ flat washer. 16. Assemble 5 x 30mm flathead screw and 5mm mounting spool with chamfer on spool under head of screw. Insert assembly thru 1 1/4″ fender washer for the 1400 or 1″ for the 800. 17. Install spool assembly into previously installed 1.2” hex adapter. Information: Do not remove washer on shock absorber. Hex adapter will protrude 1/4″ beyond fender strut. 18. Remove round cover plate over right rear shock, remove shock absorber nut and install .75″ hex adapter. 19. Assemble 5 x 30mm flathead screw, mounting spool and cup washer with chamfer on spool under head of screw. 20. Install spool assembly into previously installed hex adapter. 21. Insert 5/8” finishing plug into old turn signal hole on right side. 22. Repeat procedures on opposite side

Incoming search terms:

KTM 250/ 300/ 380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 12-11-2010

download
Repair manual KTM 250 / 300 / 380 Art No 3206004 -E 2-2C main jet jet needle jet needle air control screw idle adjusting screw idle jet throttle valve Idling range A Operation with closed throttle valve. This range is influenced by the position of the air control screw 1 and the idle adjusting screw 2 . Only make adjustments when the engine is hot. To this end, slightly increase the idling speed of the engine by means of the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Create a round and stable engine speed using the air control screw (basic position of the air control screw = open by 1.5 turns). Then adjust to the normal idling speed by means of the idle adjusting screw. Opening up B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer. Full throttle range D Operation with the throttle fully open (flat out). This range is influenced by the main jet and the jet needle. If the porcelain of the new spark plug is found to have a very bright or white coating or if the engine rings, after a short distance of riding flat out, a larger main jet is required. If the porcelain is dark brown or black with soot the main jet must be replaced by a smaller one. mixture too rich: too much fuel in proportion to air mixture too lean: not enough fuel in proportion to air 1 2 OPERATING RANGES OF THE CARBURETOR 2-3C Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB:

Incoming search terms:

Suzuki INTRUDER 1400 SLIP-ON EXHAUST SYSTEM Installation Manual

0

Filed Under (Suzuki) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosenthe mounting bolt and pinch clamp on both left and right hand mufflers. 2. Loosenthe clamp on the crossover tube, located between the two mufflers. 3. Remove the two nuts that mount the front head pipe flange to the cylinder head. 4. Remove the two nuts that mount the rear head pipe flange to the cylinder head. 5. Remove the head pipes using a twisting motion to break the seal at the muffler and to clear the cylinder head. Note : If the exhaust coupler gaskets did not remain in the mufflers, remove them from the head pipes at this time. These coupler gaskets will not be reused in your new exhaust system. 6. Remove the mounting bolt from the left hand muffler. Remove the muffler, again using a twisting motion to seperate the crossover tube and set the muffler aside. (Save the stock mounting hardware for reuse). 7. Repeat step #6 on the the right hand muffler. Set the muffler aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Reinstall the stock head pipes to the engine. Note : Leave the flange nuts loose at this time. 3. Remove the mufflers from their boxes. There are a left and right hand muffler in this system. To define the difference between the left and right mufflers, check the bracket that is welded to the back side of the muffler. Each muffler is stamped with it’s own part number. Part # D500 is the RIGHT muffler and Part # D550 is the LEFTmuffler. 4. Install a three hole mounting bracket to each of the mufflers. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16 flange head bolts (supplied), leave them loose at this time. Note : Each muffler bracket has a number stamped on it, #179 bracket is for the left hand muffler and #180 is for the right hand muffler. When the brackets are mounted correctly, the end of the bracket with the single hole should point to the inlet end (small end) of the muffler. Refer to figure 1.

SUZUKI INTRUDER 1500 LC BOTH WHEELS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 27-02-2011

download
In order to keep the proper balance on the bike lift, I would suggest that the front wheel be removed first, this is comparatively easier than the rear wheel which will be explained later. Front wheel removal : Remove the end caps, remove the front axle “Pinch Bolt” front left fork ( item (2) in manual ) remove caliper bolts both (2) both sides (2003 model year) secure calipers, secure wheel from dropping while removing axle from left side. Remove front axle, caution : there are (2) spacers on this axle, left & right, make sure you mark them, as they are both different in shape & in length, & must be re-assembled in same order to provide proper cetrallity of the front wheel with the forks & the brake calipers.both spacers have large flanges which go towards the bearing, the right spacer has (2) flanges, the largest dia. goes towards the bearing. ( very important) Now comes the tough part, I had the original stock pipes, so if you have different pipes, or your bike is a different year, (2003) your choices may be different from mine. Remove OEM right side saddlebag, slack off muffler coupling brackets # 8 & # 8a which connect muffler crossover tank to top muffler, this is where the power of the allen socket wrench set will come in handy, they’re pretty tight with the heat,remove top exhaust pipe bracket bolt (item 19 in manual) the top exhaust pipe should now swing down clear of the rear axle. You may be forced to provide more room for the exit and/or re-installation of the rear wheel by removing the bolt which secures the underside mufflet tank on the lower left side of the frame, (item # 13 in manual) then the (2) bolts, ( items # 14 in manual) which will allow the rear muffler body ( lower exhaust pipe ) to be pulled over to the right to provide access for easier rear wheel entry or removal

Incoming search terms:

KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

Incoming search terms:

Sanyang JET 50/100 and JET Euro 50/100 Specifications And Service Manual

0

Filed Under (Sym) by admin on 24-11-2010

download
Carbon monoxide If you must run your engine, ensure the place is well ventilated. Never run your engine in a closed area. Run your engine in an open area, if you have to run your engine in a closed area, be sure to use an extractor. Caution Exhaust contains toxic gas which may cause one to lose consciousness and even result in death. Gasoline Gasoline is a low ignition point and explosive material. Work in a well-ventilated place, no flame or spark should be allowed in the work place or where gasoline is being stored. Caution Gasoline is highly flammable, and may explode under some conditions, keep it away from children. Used engine oil Caution Prolonged contact with used engine oil (or transmission oil) may cause skin cancer although it might not be verified. We recommend that you wash your hands with soap and water right after contacting. Keep the used oil beyond reach of children. Hot components Caution Components of the engine and exhaust system can become extremely hot after engine running. They remain very hot even after the engine has been stopped for some time. When performing service work on these parts, wear insulated gloves and wait until cooling off. Battery Caution y Battery emits explosive gases; flame is strictly prohibited. Keep the place well ventilated when charging the battery. y Battery contains sulfuric acid (electrolyte) which can cause serious burns so be careful do not be spray on your eyes or skin. If you get battery acid on your skin, flush it off immediately with water. If you get battery acid in your eyes, flush it off immediately with water and then go to hospital to see an ophthalmologist. y If you swallow it by mistake, drink a lot of water or milk, and take some laxative such as castor oil or vegetable oil and then go to see a doctor. y Keep electrolyte beyond reach of children. Brake shoe Do not use an air hose or a dry brush to clean components of the brake system, use a vacuum cleaner or the equivalent to avoid dust flying. Caution Inhaling dust may cause disorders and cancer of the breathing system. Brake fluid Caution Spilling brake fluid on painted, plastic, or rubber parts may cause damage to the parts. Place a clean towel on the above-mentioned parts for protection when servicing the brake system. Keep the brake fluid beyond reach of children

Yamaha Road Star NEEDLE/ JET KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1. Remove the vacuum slide from the carburetor. 2. Remove the OEM needle, spacer and washers, noting order of assembly. 3. Counting from the top to the bottom, install the new Baron needle clip on groove #4 for 04-07 models and on groove #5 for 99-03 models of the replacement. NOTE: Baron adjustable needle – The top is the blunt end of the needle. 4. Reinstall the OEM spacer and washers as shown in this diagram. 5. Reinstall the vacuum slide along with the diaphragm spring. 6. Reattach the diaphragm cover back and tighten screws. NOTE: Verify that the slide maintains its full range of movement. 7. Drain the fuel from the float bowl and remove the bowl cover. 8. Remove the OEM main jet and replace it with a Barons genuine Mikuni main jet. Install the correct main jet as indicated in JET SELECTION area above on this page. Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or fitment may be required. Page: 2 BA-2420RD NEEDLE/JET KIT – Yamaha Road Star (99-07) 9. Thoroughly clean the inside of the float bowl prior to reinstalling it. 10. Reassemble the carburetor by reversing the order of step #1 through step #10. Use the new cap head allen screws in place of the OEM phillips head screws. 11. Locate the fuel mixture screw – it will either be a screw head or a brass plug. If it is a screw head, skip to step #11c. 11c. If you see a brass plug with a small hole in the center, proceed as follows: With the drill bit, carefully and slowly drill through the fuel mixture plug. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. Insert the self-tapping sheet metal screw into the drilled hole and remove the plug. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 1/2 turns. Refer to step #16 for assistance in fine tuning the setting of the air/fuel adjustment screw. 12. Reinstall the carburetor. We strongly suggest that you attach the throttle cables prior to mounting to intake manifold. 13. Reconnect the fuel line, ensuring the clamp is firmly in place. 14. Reinstall all vent hoses and electrical connectors that were previously removed, checking for any obstructions or blockage. 15. Reinstall the OEM air filter assembly or, if you are installing our Big Air Kit (BAK), follow the instructions that accompany that kit, then continue with next step. NOTES: When the BAK is installed, the vent hose that terminated on the rear of the OEM airbox can be relocated in any safe position that does not kink or pinch it. It is important to verify proper throttle operation before starting the engine.

Incoming search terms:

Suzuki Electronic Jet Kit Installation Instructions

0

Filed Under (Suzuki) by admin on 12-02-2012

download
at anytime during install or tuning please callus for any and all help, we can’thelpifyoudon’tcall ) 1. Before installing the TFI you must first disconnect the negative lead from the battery. 2. Determinea location for the TFI unit. Suggested locations areas follows: Under the seat, behinda side cover or tail section. 3. The TFIcomeswitha harness with injector connectors that match the factory injector connectors. 4. Locate the factory fuel injectors (see owners manual if you are not sure).** **: Some models are equipped with two sets of injectors (primary and secondary); the unit is designed to interface with the primary injectors. If the TFI harness does not match your injectors do not proceed and call tech support at 877-764-3337. 5. Disconnect the factory injector connectors from the fuel injectors and replace with the TFI injector connectors from the TFI unit, basically unhook the factory injector connector and plug the matching TFI connector (female) to the injector and then connect the factory injector connector to the TFI connector that simulates the injector (male). There is no order to hookup the TFI harness to the factory harness just make sure the original factory connector goes toits’original cylinder. It isa good idea to make sure there is a little slack in the harness to prevent engine vibration from damaging/breakingawireon the connectors. 6. Be sure to check the wires are not indirect contact with any sharp edges, exhaust and/or other objects, which could result in long term wear and/or damage. 7. Connect the TFI ground lead to the negative terminal of the battery along with the factory ground lead. 8. With the rubber plug removed from the TFI, turn the motorcycle key switch to the “ON”position. As the bikes electrical system goes through initial startup mode you may see LED’sflashingonthe TFI.

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

Incoming search terms: