k1100lt rear master cylinder

You search Auto repair manual PDF k1100lt rear master cylinder, if there are search results will appear below. If search results do not exist, please search by others keyword.





HARLEY DAVIDSON CHROME MASTER CYLINDER AND CLUTCH BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
MASTER CYLINDER REMOVAL See Figure 1. Master cylinders designed for dual disc (two caliper) operation have an 11/16 inch (17.5 mm) bore, while those that are designed for single disc (one caliper) operation have a 9/16 inch (14.3 mm) bore. The bore size is stamped (1) on the master cylinder assembly inboard of the handlebar clamp bracket. NOTE Do not use an 9/16 inch bore master cylinder assembly on dual disc (two caliper) models or dual disc 11/16 inch bore master cylinder assembly on single disc (one caliper) models. These master cylinder assemblies are not interchangeable. Using the wrong assembly can adversely affect braking efficiency or result in brake failure which could result in death or serious injury. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1 is 01230 1. Bore stamp size location Figure 1. Verify Correct Master Cylinder Bore Size 1. Open bleeder nipple caps on front brake caliper. Install end of a length of clear plastic tubing over caliper bleeder valves, while placing free end in a suitable container. Open bleeder valves about 1/2-turn. Pump brake hand lever to drain brake fluid. Close bleeder valve. Avoid leakage. Be sure gaskets, banjo bolt(s), brake line and master cylinder bore are clean and undamaged before assembly. (00322a) 2. Remove bolt and two steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 3. See Figure 2. Place the cardboard insert between the brake lever and lever bracket

Incoming search terms:

HARLEY DAVIDSON CHROME FRONT BRAKE MASTER CYLINDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. See Figure 2. Drain the brake fluid. a. Open bleeder nipple cap on front brake caliper. b. Install end of a length of clear plastic tubing over caliper bleeder valve, while placing free end in a suitable container. c. Open bleeder valve about 1/2-turn. d. Pump brake hand lever to drain brake fluid. e. Remove cover. f. Close bleeder valve. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 2. Remove bolt and 2 steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 3. 5/32 in. (4 mm) Cardboard Insert 3. See Figure 3. Place the cardboard insert between the brake lever and lever bracket. 4. Using T27 TORX® drive head, remove the 2 screws with flat washers securing the handlebar clamp to the master cylinder housing. Remove the brake lever/master cylinder assembly and clamp from the handlebar. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. Remove retaining ring from pivot pin groove at bottom of master cylinder bracket. 6. Remove pivot pin and brake hand lever from master cylinder assembly. NOTE New master cylinder comes with all internal components preassembled. It is not necessary to remove the components from the bore of the old master cylinder. See Figure 9. Use denatured alcohol to clean clutch system components. Do not use mineral-based solvents (such as gasoline or paint thinner), which will deteriorate rubber parts even after assembly. Deterioration of these components can cause clutch failure, which could result in death or serious injury. (00296a) 7. With denatured alcohol, clean and inspect all parts that will be reused. Replace as necessary and wipe dry with a clean lint free cloth

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

Indian Rocker Arm End Play Rear Cylinder/ Front Cylinder Installation

0

Filed Under (Indian) by admin on 12-11-2010

download
Rear Cylinder 1Rotate the engine so that the rear piston is at Top Dead Center (TDC), compression stroke, so no load is on the valves. 2Using a 3/16″ allen wrench, remove the four screws securing the rear cylinder rocker cover. 3Remove the cover and inspect both O-ring seals. Discard if damaged or worn. 4Push both rocker arms towards the valve end support bracket (A) and using a feeler gauge check the gap between the rocker arms and the pushrod end support bracket (B). NOTE: The Rocker arm end play specification should be between 0.003″ to 0.012″. 5 Compare the measurement to the specification an determine whether adjustment is necessary. If the end play is within specification, adjustment will not be required. Refit the rocker cover (instructions 14 to 15) and carry out the same inspection on the front cylinder . If the measurement is outside the specification, adjustment will be required and shimming will be necessary (follow the remainder of these instructions). Adjustment 6Using a 1/4″ allen wrench remove the 4 screws securing the rocker shaft assembly.Refit the LH support bracket and reposition the complete assembly on the rocker base. Make sure that the three dowels are in place and the slots in the rocker shafts are properly aligned with the mounting screw holes in the RH support bracket. 11Clean the threads of the 4 support bracket screws and apply Blue Loctite to the first 4 threads. 12Fit the 1-3/4″ screws into the LH support bracket (A) and the 2″ screws to the RH bracket (B). Torque all screws in cross pattern to 16-20 foot-pounds. CAUTION: The rear piston must be at TDC, compression stroke, when tightening the support bracket screws. 13Re-check the rocker end play to ensure it is within specifica- tion. 13Lubricate the two O-rings with clean engine oil and refit them in the grooves in the rocker base. 14Refit the rocker cover.

Incoming search terms:

Yamaha WR 250F and WR450F Dual Sport Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-01-2012

download
license Plate Mount Installation: Locate the aluminum license plate mount and license plate light assembly. Remove the rear most nut securing the stock taillight assembly (underneath the fender) (don’t lose the little compression tube and washer). Temporarily install the license plate mount to this location and mark the fender where it needs to be drilled for the rear mounts. Drill the fender in two places with a ¼” drill and reinstall the license plate assembly using the stock taillight mount and the 6 x 20 mm countersunk screws, bezels and nylock nuts Rear Turn Signal Installation: Locate the two rear turn signals in the kit – they’re the ones with the longer wires. Drill a 3/8 hole in each side of the fender as shown in Photo 3 and attach them as shown in Photo 4. It does no matter which signal goes on which side. Run the left turn signal wires forward along with the taillight wires, up through the grommet in the fender to the area just behind the air box cross member and above the fender. Run the right turn signal wires forward along the right frame rail, and through the same hole you made for the license plate wires Brake Light Switch Installation: The WR250/450 uses a hydraulic brake switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the rear brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the rear master cylinder guard. Remove the bolt holding the brake fluid reservoir to provide access to the master cylinder. Loosen the banjo bolt securing the rear brake line to the master cylinder. Typically, this bolt will be very tight and loosening it will bend the support hanger for the master cylinder if not supported. Brace the master cylinder with a wrench or lever. Remove the banjo bolt and replace with the hydraulic switch. Make sure to install the copper crush washer from the stock bolt under the switch. Torque the switch assembly to 25 lb-ft.

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

Yamaha Road Star Forward Control Kit Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Before starting to assemble this forward kit on your motorcycle check the packing list to make sure that the kit you received is the correct one for your model motorcycle and that the foot pegs are the style you ordered (billet or ISO). Next check the contents hardware kit P.N.0109-1000 against the packing list for completeness. Installing The Shift Control Photo 1 Remove wires from horn. Remove the two hex head bolts (Save for later installation) that mount the OEM shift controls to your motorcycle. Unthread stock shift rod at trans shift arm, leaving OEM rod end connected to stock shift arm. Using Original Metric hardware, place a drop of Loctite #242 (blue) to the bolt threads and mount the shift control plate to the motorcycle frame, Photo 2. FORWARD CONTROL KIT PM SHIFT CONTROL ASSEMBLY Note Before torquing the shift control mounting bolts down, tighten them snug and look behind the shift control mounting plate to where it contacts the mounting lug on the frame. Make sure it fits squarely to the lug before proceeding further. Torque the two shift control mounting bolts down to 25 ft-lb. Using a 3/8″ x 1″ hex head bolt with a lock and flat washer put a drop of Loctite #242 (blue) on the threads and insert the bolt through the rear of the control mounting plate and attach the foot-peg pivot to it. Tighten the bolt while holding the footpeg pivot so that its hinge is lined up in a 45˚ rear facing angle. Thread supplied shift rod coupler to stock shift rod end at trans arm. Mount the shift pedal to the other end of the shift ro d using a 5/16″ x 1″ socket head screw and Nylocnut . Adjust the transmission shift linkage so that the shift arm on the forward controls and the shift arm on the transmission are parallel. Secure it with the jam nuts. Apply a drop of Loctite #242 (blue) to the threads under the jam nut before tightening see Photo 3 After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use. A Shim Washer PHOTO 4 A B C D PHOTO 5 A PHOTO 6 PHOTO 7 Note For complete brake system removal instructions and precau – tions refer to the appropriate service manual for your year and model motorcycle

Incoming search terms:

HONDA 2002-2004 GL1800/A Linked Braking System (LBS) Proportional Control Valve (PCV) Leakage

0

Filed Under (Honda) by admin on 25-11-2010

download
1. Pump the rear brake pedal four times. •If the brake pedal feels spongy, bleed the brake system per the Service Manual. After verifying proper brake system operation, proceed to step 2 below. •If the brake pedal does not feel spongy, proceed to step 2 below. 2. Place the motorcycle on its side stand, with the handlebars in the full left position . Lock the handlebars. 3. Place a scissor jack directly under the left front brake caliper as shown in the illustration. To avoid damage to the caliper, place a protective piece of rubber (such as a piece of inner tube) between the caliper and the jack. Wind up the jack until the front wheel is approximately 15 mm off the ground. 4. Measure the distance from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). Record this measurement . • If the measured length is 30.3 mm, replace the PCV per the Service Manual. (This length indicates the unit’s secondary master cylinder is fully stroked, which means there is no hydraulic brake pressure acting on the PCV.) After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. •If the measured length is longer than 30.3 mm , proceed to step 5 below. • INSPECTION/REPAIR PROCEDURE Record this measurement. Pump the rear brake pedal four times.
GL1800/A #16 ©2005 American Honda Motor Co., Inc. – All Rights Reserved 3 of 6 FEBRUARY 2005 5. Wait 30 minutes. Do not disturb the motorcycle in any way during this time. 6. Measure the distance again from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). •If the measurement has decreased more than 1 mm from the measurement you recorded, proceed to step 7 below. •If the measurement is within 1 mm of the measurement you recorded, the PCV is OK. Proceed to the IDENTIFICATION section of this Service Bulletin. 7. Check the PCV for leakage. • If the PCV is leaking , replace the PCV per the Service Manual. After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. • If the PCV is not leaking , you must diagnose the brake system problem before proceeding. After you have diagnosed and repaired the brake system, proceed to the IDENTIFICATION section of this Service Bulletin. NOTE: Any brake system problem not related to the PCV that is found while performing this Service Bulletin is not covered by this Safety Recall. If the motorcycle’s original factory warranty is still in effect or under HPP, file a normal warranty claim. If the unit is outside its factory warranty period or HPP coverage, contact TechLine for goodwill consideration. 8. Verify proper front and rear brake operation by pumping the front brake lever and rear brake pedal before riding the motorcycle

Incoming search terms:

HARLEY DAVIDSON CHROME REAR MASTER CYLINDER COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
1. Clean rear master cylinder cover, then remove two screws that hold cover in place. 2. Remove original cover (with sight glass) and gasket. 3. Put new cover and gasket in position. 4. Install cover screws and tighten screws (1) to 6-8 in-lbs (.7-.9 Nm). Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a

Incoming search terms: