katana sputters at low rpm

You search Auto repair manual PDF katana sputters at low rpm, if there are search results will appear below. If search results do not exist, please search by others keyword.



  katana sputters at low rpm Direct Download speed 5282 Kb/s

  katana sputters at low rpm Full Version speed 6162 Kb/s



Edelbrock Nitrous Systems Digital RPM Window Switch USER MANUAL

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Programming the RPM The engine application and rpm activation points are easily selected through push buttons on the LED panel. This Switch can be programmed for a variety of engine and ignitions as shown below. 1-Cylinder This program is used for individual coil per cylinder systems (such as GM LS-1 engines, or ’99-Up Mustangs) 2-Cylinder This is for ignitions with coil packs that fire two cylinders at the same time (waste spark systems) 2-Cyl. Odd Use on coil pack ignitions that are on odd-fire engines such as a Viper V-10 or Harley-Davidson motorcycle. 4-Cylinder Typical 4-cylinder engines with a distributor. 6-Cylinder Typical 6-cylinder engines with a distributor. 6-Cyl. Odd Typical 6-cylinder odd-fire engines with a distributor. 8-Cylinder Typical 8-cylinder engines with a distributor. 1.2 Push Button LED Panel The rpm activation points and cylinder select are programmed through the push buttons on the LED panel (Figure 1) . Press the Mode button, and notice that the indicator point above the On RPM lights. When that point is on, you can scroll the rpm value up or down with the arrows on the left of the panel. Once your On rpm is set, push the Mode button until the Off RPM point lights, then set the off rpm point. Note that if the rpm point is not changed within 2-seconds, the screen returns to the current rpm reading (zero when the engine is not running). After setting the On and Off points, press the Mode button to program the Cylinder Select Valve (default is for 8-cyl.

Vespa GTS Super Specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Gts super 300 ie Gts super 125 ie s 125cc s 50cc Gts 250 ie Gts 125cc LX 125cc LX 50cc 2 stroke Engine Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder LEADER 4 stroke with electronic injection Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder, catalised, LEADER 4 stroke, 4 valve Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Capacity 278cc 124cc 124cc 50cc 249cc 124cc 124cc 49cc Power 16.4 kW / 7500 rpm 10.5 Kw / 9500 rpm 7.65 Kw / 8250 rpm 3.2 Kw / 7500 rpm 15.7 Kw / 8500 rpm 7.65 Kw / 8250 rpm 7.65 Kw / 8250 rpm 2.5 Kw / 8500 rpm Max Torque 22Nm / 6500 rpm 12 Nm / 8000rpm 9.6 Nm / 7250 rpm 4.4 Nm / 6500 rpm 20.1 Nm / 6500 rpm 9.6 Nm / 7250 rpm 9.6 Nm / 7250 rpm 3.3 Nm / 6500 rpm Cooling Liquid Liquid Forced Air Forced Air Liquid Liquid Forced Air Forced Air Starter Electric Electric Electric and kick starter Electric and kick starter Electric Electric Electric and kick starter Electric and kick starter Transmission Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Front Suspension Single arm, dual chamber hydraulic shock absorber with coaxial spring Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Rear Suspension Two dual effect shock absorbers with adjustable preload Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Twin hydraulic shock absorbers with preload adjuster Twin hydraulic shock absorbers with preload adjuster Hydraulic shock absorbers with preload adjuster Hydraulic shock absorber Front Brake ø 220mm disc brake 220mm disc brake ø 200mm disc brake ø 200mm disc brake ø 220mm disc brake ø 220mm disc brake ø 200mm disc brake ø 200mm disc brake Rear Brake ø 220mm disc brake 220mm disc brake ø 110mm drum brake ø 110mm drum brake ø 220mm disc brake ø 220mm disc brake ø 110mm drum brake ø 110mm drum brake Front Tyre Tubeless 120/70-12″ Tubeless 120/70 – 12″ Tubeless 110/70 – 11″ Tubeless 110/70 – 11″ Tubeless 120/70-12″ Tubeless 120/70-12″ Tubeless 110/70 – 11″ Tubeless 110/70-11″ Rear Tyre Tubeless 130/70-12″ Tubeless 130/70 – 12″ Tubeless 120/70 – 10″ Tubeless 120/70 – 10″ Tubeless 130/70-12″ Tubeless 130/70-12″ Tubeless 120/70 – 10″ Tubeless 120/70-10″ Running weight 158kg 158kg 114kg 96kg 151kg 145kg 114kg 96kg Length/Width/Height 2230mm / 755mm / 1170mm 1930mm / 755mm / 1930mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm 1930mm / 755mm / 1170 mm 1940mm / 755mm / 1180 mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm Fuel Tank Capacity 9 litres 9 litres 8.5 litres 8.5 litres 9.2 litres 10 litres 8.5 litres 8.5 litres Emmissions Euro 3 Euro 3 Euro 3 Euro 2 Euro 3 Euro 3 Euro 3 Euro 2 Colours Rosso Dragon Nero Lucido Montebianco Rosso Dragon Nero Lucido Montebianco Taormina Nero Lucido Montebianco Taormina Nero Lucido Montebianco Marrone Terra Di Toscana Bronzo Perseo Nero Vulcano Blu Midnight

Incoming search terms:

2007 Harley-Davidson Softail Family Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
frame Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Mild steel tubular frame; rectangular section backbone; stamped, cast and forged junctions; forged fender supports; MIG welded Swingarm Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Mild steel, round tube sections, forged junctions, MIG welded Front Fork 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers 41.3 mm telescopic, “beer can” covers Rear Shocks Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Hidden, horizontal-mounted, coil-over Caliper Type 4-piston front and rear 4-piston front and rear 4-piston front and rear Rotor Type: (diameter x width) Patented, uniform expansion rotors Patented, uniform expansion rotors Patented, uniform expansion rotors Front 292 mm x 5.08 mm 292 mm x 5.08 mm 292 mm x 5.08 mm Rear 292 mm x 5.84 mm 292 mm x 5.84 mm 292 mm x 5.84 mm Front (mm) 130 130 130 Rear (mm) 109 109 109 Engine Torque (EU standard EC95/1)5 86 ft. lb / 117 Nm @ 3200 rpm 89 ft. lb / 120 Nm @ 3300 rpm 89 ft. lb / 120 Nm @ 3300 rpm Right 29° 30° 28° Left 26° 28° 26° Battery Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating) Sealed, maintenance-free, 12V, 19-amp/hour, 270 cca (per Battery Council International Rating ) Charging Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Three-Phase, 38-amp system (439W @ 13V, 2000 rpm, 489W max power @ 13V) Starting 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement 1.2 kW electric with solenoid shift starter motor engagement Headlamp Headlamp Headlamp Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Quartz Halogen, 55-watt low beam, 60-watt high beam Tail/Stop Lights Tail/Stop Lights Tail/Stop Lights 8W/28W (5W/21W) 8W/28W (5W/21W) 8W/28W (5W/21W) Turn Signal Lights Turn Signal Lights Turn Signal Lights 28W (21W) self-canceling 28W (21W) self-canceling 28W (21W) self-canceling Indicator Lamps Indicator Lamps Indicator Lamps High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6- speed (overdrive), low fuel warnings High beam, neutral, low oil pressure, turn signals, engine diagnostics, security system6, 6-speed (overdrive), low fuel warnings Passing Lamps Chrome Vivid Black Vivid Black Vivid Black Black Cherry Pearl Black Cherry Pearl Black Cherry Pearl Deep Cobalt Pearl Black Pearl Black Pearl Pewter Pearl Fire Red Pearl Deep Cobalt Pearl White Gold Pearl Deep Cobalt Pearl Olive Pearl & Vivid Black Suede Blue Pearl & Vivid Black Suede Blue Pearl White Gold Pearl & Vivid Black Black Cherry Pearl & Pewter Pearl Olive Pearl White Gold Pearl & Deep Cobalt Pearl Fire Red Pearl & Black Pearl Pacific Blue Pearl Deep Cobalt Pearl & Pewter Pearl Pewter Pearl Yellow Pearl White Gold Pearl

Incoming search terms:

2008 – 2009 APRILIA DORSODURO 750 SLIP-ON STREEL LEGAL EXHAUST SYSTEM

0

Filed Under (Aprilia) by admin on 06-11-2010

download
Our sporty and lightweight SLIP-ON systems offer a great balance between price and performance and represent the first step in the exhaust system tuning process. The change will be also visual as our HEXAGONAL mufflers perfectly fit the exterior line of the sporty Dorsoduro and add a clean racing image. The muffler outer sleeve is made of titanium, which gives a special hi-tech touch to our SLIP-ON system. We offer street legal version with removable muffler in- serts. PERFORMANCE Measurements of the Akrapovic SLIP-ON system on the APRILIA DORSODURO 750 (without muffler insert): Power & Torque: the exhaust system modification results in a major boost in performance, delivering a solid 84.8 HP at 9540 rpm on back wheel. But the increased power isn’t available just at the top of the range; the system shows its quality already from 3500 rpm up through entire rpm range. Max. increased power between the Akrapovic and the stock system is 1.8 HP at 9300 rpm. Besides this, the torque is substantially higher in a lower rpm area from 2500 rpm to 6500, and also in middle and high rpm area. Technical specifications of Akrapovic exhaust systems and related products subject to change without notice. 20 30 40 50 60 70 80 47,5 50,0 52,5 55,0 57,5 60,0 62,5 65,0 67,5 3000 4000 5000 6000 7000 8000 9000 10000 WhlPwr EngT rq EngSpd RPM STOCK EXHAUST AKRAPOVIC SLIP-ON EXHAUST PERFORMANCE stock AKRAPOVIC max. increased power max. rear wheel power HP / rpm (measured on Dynojet ATV) 83.13 / 9560 84.8 / 9540 1.8 / 9300 ADDITIONAL DATA weight comparison (kg) stock AKRAPOVIC difference 11.13 SS link pipe TITANIUM link pipe stock – S.S. stock – TITANIUM 4.35 – 6.78 – noise measurements (dB / rpm) stock AKRAPOVIC 96 / 4375 96 / 4375

Incoming search terms:

2009 APRILIA RSV4 SLIP-ON STREET LEGAL EXHAUST SYSTEM

0

Filed Under (Aprilia) by admin on 06-11-2010

download
Our sporty and lightweight SLIP-ON systems offer a great balance between price and performance and represent the first step in the exhaust system tuning process. The change will also be visual as our HEXAGONAL muffler perfectly fit the exterior line of the RSV4 and add a clean racing image. The muffler outer sleeve is made of titanium or carbon-fiber, which gives a special hi-tech touch to our SLIP-ON system. We offer the street legal version with high flow catalytic converter and open system for race track use only. PERFORMANCE Measurements of the Akrapovic SLIP-ON STREET LEGAL/OPEN system on the APRILIA RSV4 (without muffler insert): Power & Torque: the exhaust system modification with the SLIP-ON system results in a major boost in performance, delivering a massive 167.9 HP at 12450 rpm on the back wheel. But the increased power isn’t available just at the top of the range; the system shows its quality from 4000 rpm already up through the entire rpm range. Max. increased power between the Akrapovic and the stock system is 5.2 HP at 7000 rpm. Besides this, the torque is substantially higher in a lower rpm area at 4500 rpm and from middle to high rpm area. Technical specifications of Akrapovic exhaust systems and related products subject to change without notice. 50 75 100 125 150 75 80 85 90 95 100 105 110 4000 5000 6000 7000 8000 9000 10000 11000 12000 13000 WhlPwr EngT rq EngSpd RPM STOCK EXHAUST AKRAPOVIC SLIP-ON EXHAUST PERFORMANCE stock AKRAPOVIC max. increased power max. rear wheel power HP / rpm (measured on Dynojet ATV) 165 / 12400 167.9 / 12450 5.2 / 7000 noise measurements (dB / rpm) stock AKRAPOVIC 102 / 6200 102 / 6200 legal for street use NO / YES (Street legal exhaust

Incoming search terms:

Harley Davidson Big Twin EVO Engines Edelbrock Performer-Plus Camshaft , Performer RPM Camshaft , & Performer RPM Camshaft INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-03-2012

download
Disconnect the battery. Secure the motorcycle on a suitable stand with the rear wheel off the ground. Remove components necessary for easy access to rocker covers, pushrod covers, and gear case cover, i.e., exhaust system, gas tank, air cleaner, foot rest, etc. Remove spark plugs. 2. Remove top and middle sections of rocker boxes, then rotate engine so both valves are closed on the cylinder head being worked on (put transmission in high gear and move rear wheel to slowly rotate engine). Remove the two 5/16″ bolts nearest the rocker arm shafts (keep all shafts, rocker arms, and pushrods in order so they can be installed in their original position). Remove the pushrod covers and pushrods. NOTE: The use of adjustable time-saver pushrods will simplify installation. Follow the manufacturer’s recommendations for installation of those parts. 3. It is not necessary to remove the tappet guides if you use a cam installation tool such as Crane #9-0020 to hold the tappets in place during cam installation. If you remove the tappet guides, you must use a tappet block alignment tool such as Crane #9- 0021 to re-install the tappet guides. Tappets can be held up in place during removal of guides by using U-shaped piece of safety wire or paper clip hooked to the tappets. 4. Remove ignition covers on gearcase cover by drilling out rivets to gain access to sensor plate. Remove the inner cover, sensor plate and rotor. NOTE: For re-installation, use new rivets H-D #8699 or drill and tap for 10-32 screws. 5. Remove the gearcase cover screws and remove cover while holding end of cam inward. Now remove the camshaft, spacing washer and thrust plate

Incoming search terms:

Triumph T595 Daytona and T509 Speed Triple Specifications

0

Filed Under (Triumph) by admin on 06-11-2010

download
1. Tachometer 8. Turn Indicator light 2. Tachometer ‘Red Zone’ 9. Low Oil Pressure Warning Light 3. Speedometer 10. High Beam Indicator Light 4. Odometer 11. Neutral Indicator Light 5. Trip Meter 12. Low Fuel Level Indicator Light 6. Trip Meter Reset Knob 13. Engine Management Malfunction 7. Coolant Temperature Gauge Indicator Light SPEEDOMETER The speedometer indicates the road speed of the motorcycle. In the speedometer face are the odometer and trip meter. The odometer shows the total distance that the motorcycle has travelled. The trip meter shows the distance travelled since the meter was last reset to zero. The trip meter can be reset to zero by rotating the reset knob situated on the left hand side of the speedometer. TACHOMETER The tachometer shows the engine speed in revolutions per minute – rpm (r/min). On the right side of the tachometer face is the ‘red zone’. Engine rpm (r/min) in the red zone is above maximum recommended engine speed and is also above the range for best performance. / f&it. ::;:%M,to %:th:’z zone as severe engme damage may NOTE The ‘Red Zone’ position for Daytona is different to that on the Speed Triple. Page 16
General Information COOLANT TEMPERATURE GAUGE The coolant temperature gauge indicates the temperature of the engine coolant. On the right -hand side of the gauge face is the ‘red zone. If the temperature gauge needle moves into the ‘red zone’ this indicates that the engine is overheating. needle enters the ‘red zone’ as severe WARNING LIGHTS I a0 INDICATORS When the indicator switch is turned to left or right, the corresponding direction indicator light flashes on and off. cl ~ LOW OIL PRESSURE: The low oil pressure warning light becomes illuminated whenever the oil pressure is dangerously low (or the ignition switch is in the ‘ON’ position with the engine not running). When the engine is running, the light will remain off when sufficient oil pressure is present. When starting the motorcycle, check that the light comes on when the ignition is in the ‘ON’ position, but goes out as soon as the engine starts A! CAUTION: Stop the engine immediately if the low oil pressure warning light comes on during normal operation. Do not restart the engine until the fault has been rectified. Severe engine damage will result from running the engine when the oil warning light is illuminated. HIGH BEAM: When the headlights are switched on and the headlight dip switch is set to ‘high beam’, the high beam warning light will illuminate. IElI NEUTRAL: The neutral warning light indicates when the transmission is in neutral (no gear selected). The warning light will illuminate when the transmission is in neutral with ignition switch in the ‘ON’ position. ml LOW FUEL: The low fuel indicator will illuminate when there are approximately 3.7 litres of fuel remaining in the tank. Et3 ENGINE MANAGEMENT SYSTEM MALFUNCTION INDICATOR LIGHT: The malfunction indicator light for the engine management system illuminates when the ignition is switched on, remains illuminated during starting, and goes out shortly after the engine starts. If the malfunction indicator light becomes illuminated during riding, a fault has occurred in the engine management system. In this case the system will switch to ‘limp-home’ mode so that riding may continue. Contact an authorised Triumph dealer as soon as possible to have the fault checked out and rectified

Incoming search terms:

HONDA GL1500 Headlamp Adjustments Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
Headlamp Adjusting Procedure Tools needed • Long, slender #1 Phillips screwdriver (for adjusters behind the rubber plugs) • #2 Phillips screwdriver (for the other adjuster screw) • 12-inch square of cardboard • Flat wall or garage door • Paper, tape, marker NOTE: All adjustments are very fine. You have to turn the screws A LOT to see changes in adjustment. This procedure is best done after dark, because you will need to do some test rides. Preparation 1. Set the bike on its center stand, 10 feet away from an unobstructed wall or garage door, and square to the wall or door. 2. Remove the front fairing cover and lower vent grille to gain access to the headlamp adjusters. 3. Idle the engine or connect a battery charger to the battery, to prevent battery drain. Headlamp assembly viewed from the front, showing positions of mirrors and adjusters (pretend the lens has been removed) . Low Beam Vertical Alignment 1. With the lights on low beam, cover the right half of the lamp assembly with the cardboard square, so only the left bulb is shining on the wall. 2. Using a marker, mark the top of the left low beam on the wall (use paper taped to the wall if you don’t want to mark the wall itself) . 3. Move the cardboard so it blocks the left bulb, so only the right bulb is shining on the wall. 4. The top of the right low beam should be even with the mark you made for the left low beam. If it’s not, adjust by turning the screw behind the rubber plug at the top of the lamp assembly, using a long, slender #1 Phillips screwdriver. 5. Move the cardboard back and forth between the bulbs to verify that the low beams are at the same height. On high beam, the two hotspots should line up vertically. High Beam Vertical Adjustment 1. With the lights on high beam, note the position of the beams’ hot spots on the wall in relation to the mark you made in step 5 above. 2. Most owners complain about their low beams being too low on the roadway. To correct this, lower the high beams by turning the screw behind the rubber plug at the bottom of the headlamp assembly, using a long, slender #1 Phillips screwdriver. You can watch the high beam hot spot being lowered on the wall in relation to the mark you made. 3. Take a test ride. Get out on a dark street, and adjust the high beams using the dash knob until you like what you can see. Then switch to low beam and see how that looks. 4. Repeat these steps until you get the low beam pattern you want. Left/Right Adjustment 1. Back to the wall. Set the bike on its center stand at a distance of 25 feet from the wall and square to the wall. Center the front wheel. 2. Shine the high beams on the wall. 3. Step to the back of the bike, and level your eye with the center of the passenger backrest. Use the center of the backrest and the center of the windshield like a gunsight. The center of the hotspot of the high beam should hit the wall in this line. 4. Adjust by turning the uncovered screw at the bottom of the headlamp assembly, using a #2 Phillips screwdriver.

Incoming search terms:

EDELBROCK NITROUS SYSTEM UNIVERSAL MOTORCYCLE NITROUS SYSTEM

0

Filed Under (Suzuki) by admin on 26-11-2010

download
Wiring Diagram #1 Wiring Diagram #2 Red Red Red Red Black Black Black Black Black Black Factory Harness to Horn Factory Harness to Horn Horn Horn Nitrous Solenoid Nitrous Solenoid Switch Switch Bottom View Bottom View +12V with Key On From Horn Button (Ground when button is pressed) From Horn Button (Ground when button is pressed) To Nitrous Bottle To Nitrous Bottle To Nitrous Nozzle To Nitrous Nozzle Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details. Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details ©2007 Edelbrock Corporation Brochure #63-71940 Catalog #71940 Rev. 2/07 – DC/mc Page 4of 4 To Nitrous Bottle To Nitrous Nozzle Nitrous Solenoid To Starter Solenoid Switch Bottom View Ground Starter Button +12V when Pushed Install Relay for OPTIONAL RPM Activated Switch Here. See Section 7.0 for More Details. Wiring Diagram #3 Starter Button Activation for Suzuki Hayabusa 7.0 – WIRING MSD 8950 RPM SWITCH NOTE – This is a suggested wiring application. There are many ways that the RPMswitch may be installed. The installer needs to set RPMswitch to proper RPM and test operation. Use diagrams on page 3 for relay terminal #30 connection. Nitrous Solenoid To Nitrous Bottle To Nitrous Nozzle RPM ACTIVATED SWITCH 10,000 Desired RPM Chip Here Connect as Outlined in Wiring Diagrams White to 4-Coil Tach Adapter #T-101-MSD Black Battery Ground Yellow – N/C Gray – OFF When Set RPMis Exceeded Connect as Outlined in Wiring Diagrams NOTE – RPM Chips are Ordered Separately Red to Switched +12 Volt Tailight Power or any Other +12 Volt Source with the Key On Note – This Method Will Turn the Nitrous Off When Set RPM has Been Exceeded. 85 87A 30 86 87 A Test Light Can Be Used Here to Check Operation 8.0 – OPTIONAL PRODUCTS FOR EFI MOTORCYCLES A Progressive Timing Retard Controller is available from Schnitz Racing for fuel injected motorcycles. The EFIR Series Timing Retard Controllers can be used with or without a Power Commander installed.

Incoming search terms:

2008 harley- davidson sportster specifications

0

Filed Under (Harley Davidson) by admin on 01-11-2010

download
diMensions Length 89.10 in. (2263.14 mm) Overall Width 35.20 in. (894.08 mm) Overall Height 46.80 in. (1188.72 mm) Seat Height: *•*Laden2 26.30 in. (668.02 mm) *•*Unladen* 28 in. (711.20 mm) Ground Clearance 4.40 in. (111.76 mm) Rake (steering head) 29.6° Fork Angle 29.6° Trail 4.70 in. (119.38 mm) Wheelbase 59.70 in. (1516.38 mm) Tires (Dunlop® Harley-Davidson® Series, blackwall) : *•*Front*-*D401F* 100/90-19 57h *•*Rear*-*D401* 150/80B16 71h Fuel Capacity (warning light at approximately 1 gal.) 4.5 gal. (17.03 L) Oil Capacity (w/filter) 3.60 qts. (3.41 L) Transmission Capacity 1 qts. (0.95 L) Weight: *•*As*Shipped** 557 lbs. (252.65 kg) *•*In*Running*Order* 581 lbs. (263.54 kg) *•*Gross*Vehicle*Weight*Rating* 1000 lbs. (453.59 kg) Gross Axle Weight Rating: *•*Front** 335 lbs. (151.95 kg) *•*Rear* 665 lbs. (301.64 kg) enGine Engine3 Air-cooled, Evolution® Valves* Pushrod-operated,*overhead*valves*with*hydraulic, ** self-adjusting*lifters;*two*valves*per*cylinder Bore x Stroke 3.50 in. (88.90 mm) x 3.81 in. (96.77 mm) Displacement3 73.20 cu. in. (1200 cu. cm) Compression Ratio 9.7:1 Fuel System4* Electronic*Sequential*Port*Fuel*Injection* (ESPFI) Air*Cleaner* Paper*cartridge*type Lubrication*System* Dry-sump drivetrain Primary*Drive** Chain,*57/38*ratio Final*Drive* Belt,*68/29*ratio Clutch** 9-plate,*wet Transmission 5-speed Gear Ratios (overall) : U.s.** HDI* JPN 1st 9.315 9.004 9.004 2nd 6.653 6.432 6.432 3rd 4.948 4.783 4.783 4th 4.102 3.965 3.965 5th 3.517 3.400 3.400 chassis Frame Mild steel, tubular frame; circular sections; cast junctions wing*Arm*Mild*steel,*rectangular*tube*sections,*stamped*junctions;*MIG*welded* Front Forks 39 mm Rear Shocks Coil-over; preload dual-adjustable Wheels5 (Chrome, Laced Steel option) : Black, 13-Spoke Cast Aluminum 105th Anniversary Wheels5 (Chrome, Laced Steel option) Gloss*Black*Painted*Cast*Aluminum *•*Front* 19 in. x 2.15 in. (482.60 mm x 54.61 mm) *•*Rear** 16 in. x 3 in. (406.40 mm x 76.20 mm) Brakes: *•*Caliper*Type* Dual-piston*front,*single-piston*rear* *•*Rotor*Type* (diameter x width) :** Patented,*uniform*expansion*rotors** *•*Front* 11.50 in. x .20 in. (292.10 mm x 5.08 mm) *•*Rear** 11.50 in. x .23 in. (292.10 mm x 5.84 mm) Suspension Travel: *•*Front*Wheel* 4.12 in. (104.65 mm) *•*Rear*Wheel* 2.12 in. (53.85 mm) perforMance Engine Torque6 (per SAE J1349) : *•*North*America* 79 ft. lbs. @ 4000 rpm* (107.12*NM*@*4000*rpm) *•*World** 75 ft. lbs. @ 3500 rpm* (101.70*NM*@*3500*rpm) *•*Japan* 66 ft. lbs. @ 3500 rpm* (89.50*NM*@*3500*rpm) Lean Angle (per SAE J1168) : Right: 31° Left: 30° Fuel Economy7 (EPA urban/highway test) : 42/57 mpg (5.60/4.13*L*/100*km) electric Battery** Sealed,*maintenance-free,*12V,*12-amp/hour,*200*cca (per Battery Council International Rating) Charging Single-phase, 30-amp system (357W*@*13.5V,*2000*rpm,*405W*max*power*@*13.5V) Starting* 1.2*kW*electric*with*solenoid*shift*starter*motor*engagement Lights (as per country regulation) : *•*Headlamp* (quartz halogen) * 55-watt*low*beam,*60-watt*high*beam* **•*Tail/Stop*Lights* 8W/28W* (5W/21W)* *•*Turn*Signal*Lights** 28W (21W) self-canceling *•*Indicator*Lamps* High*beam,*neutral,*low*oil*pressure,*turn*signals,** **