kawasaki mule fuel pump in tank replacement

You search Auto repair manual PDF kawasaki mule fuel pump in tank replacement, if there are search results will appear below. If search results do not exist, please search by others keyword.



  kawasaki mule fuel pump in tank replacement Direct Download speed 5282 Kb/s

  kawasaki mule fuel pump in tank replacement Full Version speed 6162 Kb/s



YAMAHA Road Star Fuel Pump Relocation Kit INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and disconnect battery. Remove fuel tank along with both left and right side battery covers, and remove air box from carburetor (all per Yamaha standard shop manual procedures). 2. Remove chrome plastic cover over fuel pump and disconnect choke cable/knob from lower pump bracket. Remove pump-to-carb fuel line from fuel pump. Disconnect fuel pumps electrical lead connector. 3. Remove two (2) hex-head pump mounting bracket bolts and remove pump assembly from motorcycle. Slide fuel pump up and off bracket mounting posts (Caution: excess fuel may drain from pump and/or fuel lines and fuel filter!). Remove heat shield. Remove remaining fuel line from pump. Pull all fuel lines from filter and remove steel springs and hose clamps from these lines (these will be reused on the kits fuel lines). With a sharp knife or box cutter, trim off the top portion of the fuel pumps rubber isolation/mount system per Photo A. Next cut pumps wiring harness approximately half way between connector and pump. Strip the insulation from the ends of these wires as well as from the supplied Baron harness extension wires. Using the supplied electrical butt connectors, crimp Baron harness extensions red wire to pumps black-w/blue-strip wire, and Baron harness extensions black wire to pumps black wire. Repeat this process on other side of wire harness extension with pumps connector. Now, referring to Photo B, you will need to cut off the square tube that runs along the side of the fuel pump with a hack saw. Cut down toward pump body in a straight cut, then cut tube off by cutting along the body. This will allow you to twist pump in the rubber mount so the curved spigot is facing up (clockwise approx 1/4 turn). 4. Remove pump-to-carb fuel line from carb and separate electrical wires from this line. Remove this fuel line from engine. Re-route choke cable to right side of engine (toward carb) and rotate it up and over rear cylinder head back toward left side of bike. Mount new Baron choke bracket to the choke cable and tighten plastic nut. New choke bracket will mount to rear fuel tank mounting location (Photo C). 5. 99~03 models – Remove electrical relay bracket (found under the right side cover) from the bike and slide each relay off of this bracket. Install fuel pump onto new Baron Fuel Pump Bracket and install bracket in the same location as the stock bracket you just removed, using stock mounting hardware. Refer to Photo F for proper installation. 6. 04~07 models Remove electrical relays from stock bracket and remove relays from rubber holder. Cut rubber holder per Photo E and replace one of the relays into the rubber and install on to new Baron bracket. The second relay will be placed to the right of the tool bag under the seat and secured with the provided two-sided tape pad. Reconnect plugs to the relays. (Photo F)

Incoming search terms:

2003 SUZUKI SV 650 FUEL SYSTEM AND THROTTLE BODY SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FUEL PUMP The electric fuel pump is mounted at the bottom of the fuel tank, which consists of the armature, magnet, impeller, brush, check valve and relief valve . The ECM controls its ON/OFF operation as controlled under the FUEL PUMP CONTROL SYSTEM . When electrical energy is supplied to the fuel pump, the motor in the pump runs and together with the impel- ler . This causes a pressure difference to occur on both sides of the impeller as there are many grooves around it . Then the fuel is drawn through the inlet port, and with its pressure increased, it is discharged through the outlet port . The fuel pump has a check valve to keep some pressure in the fuel feed hose even when the fuel pump is stopped . Also, the relief valve is equipped in the fuel pump, which releases pressurized fuel to the fuel tank when the outlet of the fuel pressure has increased up to 450 -600 kPa (4.5- 6.0 kgf/cm2,64- 85 psi) . Relief valve Brush , ∎ I,’ Check valve Magnet L Armature When the impeller is driven by the motor, pressure differential occurs between the front part and the rear part of the blade groove as viewed in angular direction due to fluid friction . This process continuously takes place causing fuel pressure to be built up . The pressurized fuel is then let out from the pump chamber and discharged through the motor section and the check valve . FUEL SYSTEM AND THROTTLE BODY 5- 3 Inlet port I I Impeller 5-4 FUEL SYSTEM AND THROTTLE BODY FUEL PRESSURE REGULATOR The fuel pressure regulator consists of the spring and valve . It keeps absolute fuel pressure of 300 kPa (3.0 kgf/cm2,43 psi) to be applied to the injector at all times . When the fuel pressure rises more than 300 kPa (3 .0 kgf/cm2, 43 psi), the fuel pushes the valve in the regulator open and excess fuel returns to the fuel tank . 90 Spring 02 Valve FUEL INJECTOR The fuel injector consists of the solenoid coil, plunger, needle valve and filter . It is an electromagnetic type injection nozzle which injects fuel in the throttle body according to the signal from the ECM. When the solenoid coil of the injector is energized by the ECM, it becomes an electromagnet and attracts the plunger. At the same time, the needle valve incorporated with the plunger opens and the injector which is under the fuel pressure injects fuel in conic dispersion . As the lift stroke of the needle valve of the injector is set constant, the volume of the fuel injected at one time is determined by the length of time during which the solenoid coil is energized (injection time)

Incoming search terms:

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

Incoming search terms:

HARLEY DAVIDSON FUEL LEVEL SENDER ADAPTER BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the currently installed fuel tank from the vehicle. Follow the instructions for the correct model vehicle under FUEL TANK: EFI, REMOVAL in the Service Manual. 3. See FUEL PUMP/FUEL GAUGE SENDING UNIT, REMOVAL in the Service Manual for instructions to: a. Unplug the fuel pump module connector. b. Remove and discard the top plate screws. c. Remove the top plate, fuel pump and fuel level sender (fuel gauge sending unit) from the tank. NOTE Take care to avoid bending the fuel level sender float rod. A bent float rod will lead to erroneous gauge readings. 2 6 1 3 4 7 9 8 5 is05284 1. Fuel level sender 2. Electrical grounding tab 3. Fuel level sender lock tab 4. Adapter bracket 5. Slot (2) 6. Terminal strip insert 7. Sender to adapter lock tab 8. Slider 9. Adapter to tank lock tab Figure 1. Fuel Level Sender Assembly to Adapter – 4. See Figure 1. Clean the electrical grounding tab (2) on the back of the fuel level sender if necessary. The tab must make firm contact with the terminal strip insert (6) in the adapter bracket. Slide the original equipment (O.E.) fuel level sender (1) into the slots (5) in the new adapter bracket (4) as shown until the lock tabs (3 and 7) snap into place. Make sure the wire is not pinched between the adapter and sender. 5. See FUEL SUPPLY CHECK VALVE/TUBE in the Service Manual. Remove the check valve/quick-connect fitting assembly from the old fuel tank, and assemble to the new tank, using a new O-ring (purchased separately). 6. Fit the slider (8) on the adapter bracket into the fuel level sender mounting channel inside the tank, and push down until the lock tab (9) snaps into place. Make sure the sender and adapter wires are not pinched between the adapter and the fuel tank tunnel, and remain accessible through the fuel tank top opening. 7. See Figure 2. Obtain the assembly of the top plate (1), regulator (2) and fuel filter (3) removed from the old fuel tank, and the stainless steel screw (8) and nut (9) provided in this kit.

Incoming search terms:

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

HARLEY DAVIDSON CHROME FUEL TANK TRIM PANEL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. Retain all seat mounting hard- ware. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 2. See the Figure 5. Remove the original fuel filler cap (A) from the tank and set it aside. Obtain a small diameter Harley-Davidson fuel filler cap (B) and screw it into the fuel filler opening. For Model XL883C, or other models equipped with Genuine Motor Parts Large Capacity Fuel Tank 3. To ensure surface cleanliness, clean the top of the fuel tank with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. 4. Measure and mark the centerline of the fuel tank, with a wax pencil or water-based marker, at the rear of the tank as shown in Figure 3. Proceed to Step 10. For Model XL1200C 2 1 is 01910 1. Original fuel tank trim panel liner 2. Fishing line (or string) Figure 1. Removing the Existing Trim Panel (XL 1200C) 5. See Figure 1. Insert the fishing line (2) between the rear of the fuel tank and the liner (1) on the underside of the original trim panel. NOTE Raise the ends of the fishing line away from the fuel tank to avoid scuffing the tank finish 6. Using a side-to-side “sawing” motion, work the fishing line toward the front of the fuel tank to break the adhesive bond between the trim panel and the tank. 7. Carefully pull the trim panel and liner off of the tank and discard it. NOTE Be careful not to scratch the paint on the fuel tank when removing the adhesive

Incoming search terms:

YAMAHA YZF-R125 SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
Fuel tank cap To remove the fuel tank cap 1. Open the fuel tank cap lock cover. 2. Insert the key into the lock and turn it 1/4 turn counterclockwise. The lock will be released and the fuel tank cap can be removed. To install the fuel tank cap 1. Push the fuel tank cap into position with the key inserted in the lock. 2. Turn the key clockwise to the original position, and then remove it. 3. Close the lock cover. NOTE: The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. WARNING EWA11140 Make sure that the fuel tank cap is properly installed before riding. EAU13211 Fuel Make sure that there is sufficient fuel in the tank. Fill the fuel tank to the bottom of the filler tube as shown. WARNING EWA10880 Do not overfill the fuel tank, otherwise it may overflow when the fuel warms up and expands. Avoid spilling fuel on the hot en- gine. 1. Fuel tank cap lock cover 2. Unlock. 1. Fuel tank filler tube 2. Fuel level
INSTRUMENT AND CONTROL FUNCTIONS 3-8 3 CAUTION: ECA10070 Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. EAU43420 CAUTION: ECA11400 Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, such as the valves and piston rings, as well as to the exhaust system. Your Yamaha engine has been designed to use premium unleaded gasoline with a research octane number of 95 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand. Use of unleaded fuel will extend spark plug life and reduce maintenance costs. EAU13442 Catalytic converters This vehicle is equipped with catalytic converters in the exhaust system. WARNING EWA10860 The exhaust system is hot after operation. Make sure that the exhaust system has cooled down before doing any maintenance work. CAUTION: ECA10700 The following precautions must be observed to prevent a fire hazard or other damages. Use only unleaded gasoline. The use of leaded gasoline will cause unrepairable damage to the catalytic converter. Never park the vehicle near possible fire hazards such as grass or other materials that easily burn. Do not allow the engine to idle too long.

Ducati Hypermotard Large Fuel Tank Installation Instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
REMOVING THE OEM FUEL TANK GO FOR A RIDE The best way to remove fuel from your original fuel tank is to RIDE your bike. You should already be familiar with how low you can go and the less fuel that’s in your tank before you start means the less mess you make when draining it. HM69 Fuel Tank Installation Instructions This manual is provided for marketing and informational purposes only and is a guide to assist experienced motorcycle technicians with the installation of the HM69 fuel tank. This installation involves gasoline. Improper installation, adjustment, alteration, service or maintenance regarding the HM69 fuel tank can cause property damage, personal injury or death. At-home Do-It-Yourself mechanics should not install the HM69 fuel tank if you are uncertain of your ability to properly install it and refer the installation to an authorized Ducati service department. ! REMOVE THE SEAT Remove the seat bolt at the rear of the seat with a 4mm hex key. To remove the seat, grasp both sides of the seat, lift the rear of the seat slightly, and pull the seat to the rear of the bike. The front of the seat engages onto bolts on either side of the fuel tank and can be stubborn. THIS KIT ALSO CONTAINS: © 2009 California Cycleworks, Inc. Questions? Email orders@ca-cycleworks.com 1
REMOVE THE BODYWORK The tank cover is fi rst. Remove the fuel fi ller cap and then the 4 screws you see: 2 near the front of the cover and the two aside the fi ller neck. Lift up on the forward portion of the cover and move the entire cover rearward so that the back of the cover is away from the retaining contour on the fuel tank. SIDE PANELS Remove the right side panel’s inner cover using a large coin. Both left and right side covers are retained by 3 screws with 4mm hex heads. Remove the 2 screws on the side of the tank (which were revealed with the removal of the seat). While holding the side covers to support them, remove the bottom screw. The left side cover pulls away naturally – take care not to drop the cover as the tool kit is housed inside of it, adding unexpected weight

Incoming search terms:

How to change a fuel filter on 1998 Ducati ST2

0

Filed Under (Ducati) by admin on 26-10-2010

download
1. On a cool bike, parked on center-stand, remove the two button-head bolts securing the key cover on the top of the fuel tank. Set cover aside, and save bolts, they will be used later. 2. Remove the seat 3. Un-hook front clip holding the tank down. 4. Lift tank upward, rotating on rear pin, and place prop-rod in place to secure tank in upright position. (If possible, you may want to find a longer prop to put the tank at a higher angle. This allows the fuel pump to be a bit more accessible. I used a long piece of rod iron, and propped the tank up by its rubber side bumpers.) 5. Pad the area directly under the fuel pump very well with paper shop towels or other very absorbent materials, as gas will likely drip. 6. Disconnect the electrical connector going to the fuel pump.
7. There are two fuel lines going to the fuel pump. One is marked with a white collar that has the letter R on it, the other has a M . Take note of which is which. The R line goes in the middle stem, and the M connects to the stem that is closest to the outside edge of the tank. It is a good idea to take a permanent marker, and write a ” R ” and ” M ” near these connections on the bottom of the fuel filter so as to not forget. 8. One at a time, loosen the hose clamps on the lines, and remove them from their stems. Some fuel will spill. It will stop however; have plenty of paper-towels close on hand. (The hose clamps should be 7mm) Also remove the small gas overflow tube that is attached to the fuel pump. 9. Remove the rear latch that the tank rotates on, and lift the tank off of the bike. 10. Lean the tank forward so as to move the gas forward, and remove the drain plug at the very rear of the tank with a 5mm Hex Key

SUZUKI VZR1800K6 And VZR1800/ ZK7 FUEL DELIVERY PIPE REPLACEMENT

0

Filed Under (Suzuki) by admin on 26-11-2010

download
NOTE: The fuel delivery pipe assembly can be removed from the throttle body without removing the throttle body assembly from the motorcycle. 1) Refer to section 6 of the service manual to remove the fuel tank and the air cleaner box. Place shop rags over the bore of each throttle body to prevent anything from falling into the engine through the throttle bodies. 2) Remove the wire harness clamp, disconnect the fuel injector couplers A and move the harness aside. 3) Remove the four fuel delivery pipe assembly mounting screws and remove the fuel delivery pipe assembly. 4) Replace the o-rings and seals with the new parts supplied in the kit (apply a small amount of engine oil to the o-rings and seals to ease the installation of the injector). To prevent damage to the o-rings or seals, don’t turn the injector when pushing it into the fuel delivery pipe and throttle body respectively. Install the new fuel delivery pipe assembly in the reverse order of removal. 5) Connect the fuel injector couplers A and clamp the injector harness to the fuel delivery pipe. DO NOT overtighten the harness clamp. 6) Connect the fuel tank, remove the shop rags from over the bore of each throttle body, and run the engine, checking for fuel leaks. DO NOT reuse the original fuel hose connector retainer. Confirm that the fuel hose connector has completely seated and locked (clicked) into position before turning on the ignition switch. 7) Refer to section 6 of the service manual to install the air cleaner box and the fuel tank. 8) Test ride the motorcycle to confirm proper operation. FUEL DELIVERY PIPE ASSEMBLY REPLACEMENT PROCEDURE

Incoming search terms: